In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.
Signed-off-by: Simon Glass <sjg@chromium.org>
Correct the ALIGN macro usage in mmu_set_region_dcache_behaviour
call: the address must use ALIGN_DOWN and size can use ALIGN macro.
With STM32_SYSRAM_BASE=0x2FFC0000 and MMU_SECTION_SIZE=0x100000 for
STM32MP15x the computed address was 30000000 instead of 2ff00000.
Fixes: 43fe9d2fda ("stm32mp1: mmu_set_region_dcache_behaviour")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
In pre-reloc stage, U-Boot marks cacheable the DDR limited by
the new config CONFIG_DDR_CACHEABLE_SIZE.
This patch allows to avoid any speculative access to DDR protected by
firewall and used by OP-TEE; the "no-map" reserved memory
node in DT are assumed after this limit:
STM32_DDR_BASE + DDR_CACHEABLE_SIZE.
Without security, in basic boot, the value is equal to STM32_DDR_SIZE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove the unnecessary inversion on the eth_env_set_enetaddr() result which
only make complex the code of setup_mac_address() and display an invalid
value in the associated pr_err.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Since commit d877f8fd0f ("arm: provide a function for boards init
code to modify MMU virtual-physical map") the parameter of
mmu_set_region_dcache_behaviour need to be MMU_SECTION_SIZE
aligned.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As the dbgmcu_init use the function bsec_dbgswenable which is based
on the DM and DT, its call can't be done before the spl is initialized
(driver model, DT and malloc) in board_init_f::spl_early_init().
This function call is moved later in spl_board_init().
Fixes: bd3f60d29c ("arm: stm32mp: protect DBGMCU_IDC access with BSEC")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As debugger must be totally closed on Sec closed chip,
the DBGMCU_IDC register is no more accessible (self
hosted debug is disabled with OTP).
This patch adds a function bsec_dbgswenable() to check
if the DBGMCU registers are available before to access them:
BSEC_DENABLE.DBGSWENABLE = self hosted debug status.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Activate the data cache in SPL and in U-Boot before relocation.
In arch_cpu_init(), the function early_enable_caches() sets the early
TLB, early_tlb[] located .init section, and set cacheable:
- for SPL, all the SYSRAM
- for U-Boot, all the DDR
After relocation, the function enable_caches() (called by board_r)
reconfigures the MMU with new TLB location (reserved in
board_f.c::reserve_mmu) and re-enable the data cache.
This patch allows to reduce the execution time, particularly
- for the device tree parsing in U-Boot pre-reloc stage
(dm_extended_scan_fd =>dm_scan_fdt)
- in I2C timing computation in SPL (stm32_i2c_choose_solution())
For example, the result on STM32MP157C-DK2 board is:
1,6s gain for trusted boot chain with TF-A
2,2s gain for basic boot chain with SPL
For information, as TLB is added in .data section, the binary size
increased and the SPL load time by ROM code increased (30ms on DK2).
But early malloc can't be used for TLB because arch_cpu_init()
is executed before the early poll initialization done in spl_common_init()
called by spl_early_init() So it too late for this use case.
And if I initialize the MMU and the cache after this function it is
too late, as dm_init_and_scan and fdt parsing is also called in
spl_common_init().
And .BSS can be used in board_init_f(): only stack and global can use
before BSS init done in board_init_r().
So .data is the better solution without hardcoded location but if you
have size issue for SPL you can deactivate cache for SPL only
(with CONFIG_SPL_SYS_DCACHE_OFF).
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a function get_cpu_dev to get the DEV_ID present
in DBGMCU_IDC register.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Manage BOOT_FLASH_SPINAND, with boot_device="spi-nand"
and treat this value in bootcmd_stm32mp.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The STM32MP1 series is available in 3 different lines which are pin-to-pin
compatible:
- STM32MP157: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz,
3D GPU, DSI display interface and CAN FD
- STM32MP153: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz
and CAN FD
- STM32MP151: Single Cortex-A7 core, Cortex-M4 core @ 209 MHz
Each line comes with a security option (cryptography & secure boot)
& a Cortex-A frequency option :
- A : Cortex-A7 @ 650 MHz
- C : Secure Boot + HW Crypto + Cortex-A7 @ 650 MHz
- D : Cortex-A7 @ 800 MHz
- F : Secure Boot + HW Crypto + Cortex-A7 @ 800 MHz
This patch adds the support of STM32MP15xD and STM32MP15xF in U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add a function get_soc_name to get a string with the full name
of the SOC "STM32MP15xxx Rev.x"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add BSEC lock access (read / write) at 0xC0000000 offset of misc driver.
The write access only available for Trusted boot mode, based on new
SMC STM32_SMC_WRLOCK_OTP.
With the fuse command, the permanent lock status is accessed with
0x10000000 offset (0xC0000000 - 0x8000000 for OTP sense/program
divided by u32 size), for example:
Read lock status of fuse 57 (0x39)
STM32MP> fuse sense 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
Set permanent lock of fuse 57 (0x39)
STM32MP> fuse prog 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
WARNING: the OTP lock is updated only after reboot
WARING: Programming lock or fuses is an irreversible operation!
This may brick your system.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add support for Rev.Z of STM32MP15x cpu.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Let board code override setup_mac_address(), which is useful e.g. if the
board derives the MAC address from another source, like an I2C EEPROM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Reset ResourceTableAddress and CoprocessorState at cold boot, preserve
these values at standby wakeup.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch solves the following warnings:
arch/arm/mach-stm32mp/cpu.c:378:16: warning: comparison between signed
and unsigned integer expressions [-Wsign-compare]
if (instance > ARRAY_SIZE(serial_addr))
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Without newline, the error message appears for non prgrammed OTP boards
looks messsy. Hence add it to look more clean.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- export the function get_bootmode() and reused it in spl code
- manage uart instance by alias (prepare v4.19 binding)
- solve issue on nand instance
- restore console for uart boot
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32
The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power
The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
At present these functions return 0 on success. For some devices we want
to know how many bytes were transferred. It seems useful to adjust the API
to be more like the POSIX read() and write() functions.
Update these two methods, a test and all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Use OTP57 and 58 for MAC address
- OTP57 = MAC address bits [31:0]
- OTP58 = MAC address bit [47:32] stored in OTP LSB's
Use manufacture information in OTP13 to OTP15 to build unique
chip id saved in env variable "serial#"
(used for USB device enumeration)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add the needed information to enable the debug uart
to have printf before the serial driver probe
(so before probe for clock, pincontrol and reset drivers)
To enable the debug on uart 4 (default console):
+ CONFIG_DEBUG_UART=y
+ CONFIG_DEBUG_UART_STM32=y
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support of sysreset with generic driver "syscon-reboot"
provided by RCC, for U-boot and for SPL.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
SPL copy BootRom boot mode information
in TAMP register 21.
This TAMP register information is used
after relocation to set 2 env variables
- boot_device
- boot_instance
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader
- using driver model for all the drivers, even in SPL
- all security feature are deactivated (ETZC and TZC)
- reused STM32 MCU drivers when it is possible
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
