The IRAM on PX30 (or Int_MEM in datasheet) starts at 0xff0e0000 and not
0xff020000 as rightfully stated in the FIXME comment.
Let's fix it so that BROM_BOOTSOURCE_ID_ADDR points to the correct
address for PX30.
Fixes: 46281a76be ("rockchip: add core px30 headers")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
The grf and cru are only used when no UART base is provided by the user
(defaults to UART2) or for UART1, UART3 and UART5 to be used for the
debug UART. Therefore, let's surround those variable definitions with
the proper checks.
This wasn't an issue before support for UART0 was added, because all
cases were using cru and grf. UART0 only uses pmucru so there's a need
to not define those variables anymore.
Fixes: d0af506625 ("rockchip: px30: support debug uart on UART0")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pinephone Pro is another device by PINE64. It's closely related
to the Pinebook Pro of which this initial support is derived from.
Specification:
- A variant of the Rockchip RK3399
- A 6 inch 720*1440 DSI display
- Front and rear cameras
- Type-C interface with alt mode display (DP 1.2) and PD charging
- 4GB LPDDR4 RAM
- 128GB eMMC
- mSD card slot
- An AP6255 module for 802.11ac WiFi and Bluetooth 5
- Quectel EG25-G 4G/LTE modem
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Initial support for the PinePhone Pro has now landed upstream in
Linux 6.1 RC1 so sync the dts from 6.2-rc1 for initial support.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Neural Compute Module 2(Neu2) IO board is an industrial form factor
IO board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Add u-boot,dm-spl and u-boot,dm-pre-reloc related properties
for Rockchip RV1126 SoC.
Both eMMC and SD boot are tested in Edgeble Neu2 SoM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 2(Neu2) IO board is an industrial form factor
evaluation board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Neural Compute Module 2(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RV1126 from Edgeble AI.
General features:
- Rockchip RV1126
- 2/4GB LPDDR4
- 8/16/32GB eMMC
- 2x MIPI CSI2 FPC connector
- Fn-link 8223A-SR WiFi/BT
Industrial grade (-40 °C to +85 °C) version of the same class of module
called Neu2k powered with Rockchip RV1126K.
Neu2 needs to mount on top of Edgeble IO boards for creating complete
platform solutions.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Add support for rv1126 package header in mkimage tool.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Unsecure the dram area so that MMC, USB, and SFC controllers
can able to read data from dram.
Signed-off-by: Jason Zhu <jason.zhu@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip RV1126 is a high-performance vision processor SoC
for IPC/CVR, especially for AI related application.
Add arch core support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change-Id: I22fde40ec375e3c6aba39808abf252edc45d4b04
RV1126 is a high-performance vision processor SoC for IPC/CVR,
especially for AI related application.
It is based on quad-core ARM Cortex-A7 32-bit core which integrates
NEON and FPU. There is a 32KB I-cache and 32KB D-cache for each core
and 512KB unified L2 cache. It has build-in NPU supports INT8/INT16
hybrid operation and computing power is up to 2.0TOPs.
This patch add basic core dtsi support.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Add power-domain header for RV1126 SoC from description in TRM.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add clock driver support for Rockchip RV1126 SoC.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the dt-bindings header for the Rockchip RV1126, that gets shared
between the clock controller and the clock references in the dts.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some pins in rockchip are routed via Top GRF and PMU GRF
instead of direct regmap.
Add support to handle all these routing paths so that the
SoC pinctrl drivers will use them accordingly.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Control the ddr init print messages via RAM_ROCKCHIP_DEBUG
instead of printing by default.
This gives an option to configs to enable these prints or
not.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add full ddr pctl registers and bit masks for px30.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
DDR chip capacity is computed based on GRF split in some
Rockchip SoC's like PX30 and RV1126.
Add split argument in ddr print info so-that the respective
ddr driver will pass the grf split.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We have common ddr types in rockchip or in general. So use
the common ddr type names instead of per Rockchip SoC to
avoid confusion.
The respective ddr type names will use on the associated
ddr SoC driver as these drivers are built per SoC at a time.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ram-uclass is building irrespective of whether TPL_DM
or SPL_DM is enabled. So control the ram uclass build
based on TPL/SPL_DM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable efuse support which allows reading of the cpuid#, serial#
and also generates a unique mac address from the board's serial.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is read-only data, so mark it as such.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Key data is never written so the parameter can be const, which allows
putting fixed keys in .rodata.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This synchronizes the Device Trees related to Puma RK3399 SoM with Linux
kernel next-20221114 to include two important changes pertaining to
eMMC and SD card instability.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the PCLK_WDT_NS clock to px30_clk_enable so that the watchdog driver
can probe since it wants to enable this clock.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
By default, the PX30 is configured for watchdog and tsadc to trigger a
second global reset which is a more permissive reset than first global
reset.
From TRM part 1 "2.3 System Reset Solution":
glb_srstn_1 will reset the all logic, and
glb_srstn_2 will reset the all logic except GRF, SGRF and all GPIOs.
This enforces that the watchdog and tsadc trigger glb_srstn_1 as
similarly done for RK3399 in U-Boot (in SDRAM driver for some reason?),
TF-A and Coreboot.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Pullup is used by the usb framework in order to do software-controlled
usb_gadget_connect() and usb_gadget_disconnect().
Implement pullup() for dwc2 using the SOFT_DISCONNECT bit in the dctl
register:
* when pullup is on, clear SOFT_DISCONNECT
* when pullup is off, set SOFT_DISCONNECT
This is especially useful when a gadget disconnection is initiated but
no board_usb_cleanup() is called.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The patch fixes the following error when updating a BSH SMM S2 board:
3:72>Start Cmd:FB[-t 8000]: ucmd nand write ${loadaddr} nanddtb ${filesize}
3:72>Okay (0.023s)
3:72>Start Cmd:FB: reboot
3:72>Fail Bulk(R):LIBUSB_ERROR_IO(0s)
The "fastboot reboot" command detaches the USB when it still needs to be
used. So let's detach the USB just before the reset.
CC: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Fixes: 5f7e01e9d5 ("usb: gadget: fastboot: detach usb on reboot commands")
Suggested-by: Michael Trimarchi <michael@amarulasolutions.com>
Co-developed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add a new CONFIG_USB_HUB_DEBOUNCE_TIMEOUT to increase the
HUB_DEBOUNCE_TIMEOUT value, for example to 2s because some usb device
needs around 1.5s or more to make the hub port status to be
connected steadily after being powered off and powered on.
This 2s value is aligned with Linux driver and avoids to configure
"usb_pgood_delay" as a workaround for connection timeout on
some USB device; normally the env variable "usb_pgood_delay" is used
to delay the first query after power ON and thus the device answer,
but this variable not used to increase the connection timeout delay.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This enables MMC support, which is available
on Condor board, by default.
Signed-off-by: Andrey Dolnikov <andrey.dolnikov@cogentembedded.com>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
The eMMC card has two supplies, VCC and VCCQ. The VCC supplies the NAND
array and the VCCQ supplies the bus. On Condor, the VCC is connected to
3.3V rail, while the VCCQ is connected to 1.8V rail. Adjust the pinmux
to match the bus, which is always operating in 1.8V mode.
Based on Linux commit 69efe4bbeda50745 ("arm64: dts: renesas: condor:
Switch eMMC bus to 1V8") from Wolfram Sang
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
This board requires SPI NOR fast-read, otherwise the SPI NOR
access returns corrupted data. Enable the fast-read explicitly
in DT as it has been disabled in the MTD subsystem by commit
d008190920 ("mtd: spi-nor: Mask out fast read if not requested in DT")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Since R-Car Gen3 already enables position independent build, also set
CONFIG_TEXT_BASE=0x0 to finalize the switch. This is possible since
534f0fbd65 ("arm64: Fix relocation of env_addr if POSITION_INDEPENDENT=y")
fixed current env_get_char() crash with CONFIG_TEXT_BASE=0x0 .
This change permits us to start U-Boot from any location in DRAM instead
of specific TEXT_BASE.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Since R-Car Gen3 already enables position independent build, also set
CONFIG_TEXT_BASE=0x0 to finalize the switch. This is possible since
534f0fbd65 ("arm64: Fix relocation of env_addr if POSITION_INDEPENDENT=y")
fixed current env_get_char() crash with CONFIG_TEXT_BASE=0x0 .
This change permits us to start U-Boot from any location in DRAM instead
of specific TEXT_BASE.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 30 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 29 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 34 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 32 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 32 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
