This adds a udevice parameter to get_best_delay and msdc_set_mclk so they
can call dev_err properly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Call mmc_of_parse at probe time to fetch all the host properties
from the DT.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The second clock of the IP block (the generic clock), must be explicitly
enabled.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Peng Fan <pengfan@nxp.com>
clk_set_rate will return rate in case of success and zero in case of
error, however it can also return -ev, but it's an ulong function.
To avoid any issues, disregard the return value of this call.
In case this call actually fails, nothing much we can do anyway, but we
can at least try with the previous values (or DT assigned-clocks)
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add new compatibility string for matching sama7g5 product.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The existing driver is not compatible with the Driver Model.
This patch makes the necessary changes while also removing obsolescent
calls/properties as follows:
- fdtdec_* calls replaced with dev_read_* equivalents;
- 'clock-freq-min-max' property replaced by querying the frequency of
the source clock 'base_clk';
- The card detect erratum workaround is applied during probe rather than
overriding get_cd.
The card detect workaround (Microchip ref. DS80000736E, erratum #15) is
not always needed and can be disabled using a vendor specific DT
property.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
Currently, after config the clock rate, delay 10ms, this is quite a rough
method. Check the clock stable status in the present status register is
enough.
Tested-by: Ji Luo <ji.luo@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Use mmc_of_parse() to set the common host properties. That includes
"bus-width", so parsing it can be removed from the driver.
But more importantly, "non-removable" is now respected, which fixes
the usage of eMMC.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Marek Behún <marek.behun@nic.cz>
Since the introduction of 'get_cd' callback in sdhci core,
dragonboard410c's MMC interface is broken. It turns out that 'get_cd'
callback checks for the host_caps for validating the chip select. And
since the msm_sdhci driver is not parsing the host_caps from DT, not
all of the cababilities are parsed properly. This results in the MMC
interfaces to be broken.
Hence, fix this by adding a call to 'mmc_of_parse' during driver probe.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Aníbal Limón <anibal.limon@linaro.org>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- The SDIO signal voltage and max base clock frequency
setting are missing in driver, which causes SDIO
not working.
- The patch adds SDIO signal voltage switch support,
which is based on regulator-gpio of vqmmc-supply, and
sets the max base clock frequency.
- Fix the zero clock value in call to sdhci_setup_cfg()
function.
Change-Id: I79c8860c65b8db166f4f70db56ede4097f71f1fa
Signed-off-by: Evan Wang <xswang@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/53589
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: Hua Jing <jinghua@marvell.com>
[pali: Amended fixup patch]
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
Adds support for MMC controllers found on OcteonTX or
OcteonTX2 SoC platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Peng Fan <peng.fan@nxp.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To help this tedious work, this commit converts devfdt_get_addr_ptr()
to dev_read_addr_ptr() by coccinelle. I also removed redundant casts
because dev_read_addr_ptr() returns an opaque pointer.
To generate this commit, I ran the following semantic patch
excluding include/dm/.
<smpl>
@@
type T;
expression dev;
@@
-(T *)devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
@@
expression dev;
@@
-devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of recasting and shifting use macros which are designed for taking
upper/lower 32bit value from 64bit variable.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The capabilities register has a field to indicate whether the host
supports high speed mode or not. Add high speed host_caps based on
this bit instead of enabling it by default.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilnx.com>
Tested-by: Michal Simek <michal.simek@xilnx.com>
(zcu104 with sdhci-caps-mask = <0 0x200000>;)
DT binding is saying that default value is 0 not -1 that's why fix it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
s/xlnx,mio_bank/xlnx,mio-bank/g
DT binding is describing mio-bank not mio_bank that's why fix all DTSes and
also driver itself.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The hardcoded array size leads to array overflows with changes in
speed modes enum in mmc core. Use MMC_MODES_END for otap_del_sel
array declaration to fix this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
4hKj5yxRg3cvb/pBAmbQ
=TyRs
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
After enabling OF_PLATDATA support to both MMC and GPIO drivers add the
support for card detection.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to reduce the footprint of SPL by removing dtb and library
overhead, add OF_PLATDATA support to fsl_esdhc_imx. This initial
approach does not support card detection, which will be enabled after
adding OF_PLATDATA support to GPIO.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As discussed in commit <addf358bac1d2bd0> rename fsl_esdhc_imx
driver to allow the OF_PLATDATA support.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Refactor to allow any arch to create SPI-flash images
New button uclass
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8g33sRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaeEgf/QhmJjd6lEE3ABncRa3texyqq7j9eu+9P
2JMCahrIzps83LLOkzNSGs1+m1hRuTcdnYNV8FxdmkAjDTYwV5RHOfwtpAr2nkH2
HBbJRA2qMPleqT8wcymouhaCIRTTCGfUkFgZ+OowwSlHnQ4d2oGU/59Z+AkbpfX0
3svA1Mlr5rUTZ3qTvdsepuZckuYOTGYZ5jgjbgr+G8F4iW4Ov+OkBxqDz9zFCveF
md5CHKP1SV+bq67Q9uqUEwatLzYpy1p24j1Qe4G08U1+XCi6r+95VEc7TWxggboj
eV/5d/sZbGESAtJiJ4TmqpGVcOLzBLI0FOunky0JNFwdcyRS/6KcCg==
=Xjil
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-28jul20' of git://git.denx.de/u-boot-dm
Use binman instead of one of the Rockchip build scripts
Refactor to allow any arch to create SPI-flash images
New button uclass
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- driver changed to DM.
- pinctrl-driver/dt is used now instead of configuring the mmc I/O-pins
in the mmc-driver.
- nexell_dwmmc_ofdata_to_platdata() reworked, i.e. valid default values
are used now (where possible) and the appropriate if-blocks have
been removed.
- new dt-property "mmcboost" is used now instead of "CONFIG_BOOST_MMC"
which was not defined anywhere.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
After latest improvements on OF_PLATDATA struct names are generated
based on driver name instead of compatible strings. With this in mind,
using aliases in drivers are not longer needed.
This patch removes code that tried to handle these kind of aliases to
improve readability.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
The eSDHC adapter card identification and multiplexing configuration
through FPGA had been implemented in both common mmc driver and
fsl_esdhc driver. However it is proper to move these code to board
files and do it during board initialization. The FPGA registers are
also board specific.
This patch is to move eSDHC adapter card identification and
multiplexing configuration from mmc driver to specific board files.
And the option CONFIG_FSL_ESDHC_ADAPTER_IDENT is no longer needed.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Rebased, Removed T1040QDS change as board does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The sdhc_adapter of global data has not been used, and we
do not have to use it as global data even we may need it
in the future.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The r8a774a1 is compatible with the generic rcar-gen3-sdhi controller.
This patch adds the compatibilty flag, to support the SDHI controller.
Signed-off-by: Adam Ford <aford173@gmail.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Write required information into the SSDT to describe the SD card
card-detect pin. Since the required GPIO properties are not present in
the device-tree binding, set them manually for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
As per the SD physical layer specification version 7.10, erase
command (CMD38) and stop transmission command (CMD12) will generate
R1b response.
R1b = R1 + busy signal
A non-zero value after the R1 response indicates card is ready for
next command.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Erase block start address (CMD32) and erase block end address (CMD33)
command will generate R1 response for mmc SPI mode.
R1 response is 1 byte long for mmc SPI, so assign 1 byte as a response
for this commands.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Send status command (CMD13) will send R1 response under SD mode
but R2 response under SPI mode.
R2 response is 2 bytes long, so read 2 bytes for mmc SPI mode
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
The content of ssr is useful only for erase operations.
This saves erase time.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
R1 response is 1 byte long for mmc SPI commands as per the updated
physical layer specification version 7.10.
So correct the resp and resp_size for existing commands
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
When variable i will become 0, while(i--) loop breaks but variable i will
again decrement to -1 because of i-- and that's why below condition
"if (!i && (r != resp_match_value)" will never execute, So doing "i--"
inside of while() loop solves this problem.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
In commit commit d2c05f50e1 ("mmc: omap_hsmmc: Set 3.3V for IO voltage")
was changed 3.0V IO voltage to 3.3V but it was not done on all places in
omap_hsmmc driver. That commit broke eMMC support on Nokia N900.
This patch fixes that problematic commit and changes 3.0V to 3.3V on all
remaining places in omap_hsmmc driver.
Fixes: d2c05f50e1 ("mmc: omap_hsmmc: Set 3.3V for IO voltage")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Faiz Abbas <faiz_abbas@ti.com>
patman support for Python3 on Ubuntu 14.04
new checkpatch check to avoid #ifdefs
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8InaQRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreazvAgAgqyvPY2o+BNHscrx9/6sEOHSAVty/D5t
SdaphzRezlJOWy9MC/ZyqyevZjogN7fgGNQVgh/I4BklIc/N5Omn68/+JWylSFVP
taJKiJD1IVSThTXGOMTxlDiTxY7NfVDUDjtFIpCDswBrnSJlX+2v/RsehUwVIrYn
NJwiRXd33IdS1vh1mqqNgwbZNBo+zGWn5LApq71vLSVkiQlmcpMG9FmYYRcg/AhG
3Xd2HB2ANcvb13fMMcwd3s4WPNYoiJvwjSHScNDUPEip7XeZNDiNeq4gC6d2Uw+J
zC3/vOCP3eRtAnr6syJ5QcGN/eeKwLtnTE+fOuOm6s5Y98po4iMykA==
=3fC5
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10jul20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
of-platdata: better phandle and compatible-string support
patman support for Python3 on Ubuntu 14.04
new checkpatch check to avoid #ifdefs
On build with 32 bit, there is a warning for int-to-pointer-cast.
Fix the int to pointer cast by using uintptr_t.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
In the current implementation, when dtoc parses a dtb to generate a struct
platdata it converts the information related to linked nodes as pointers
to struct platdata of destination nodes. By doing this, it makes
difficult to get pointer to udevices created based on these
information.
This patch extends dtoc to use struct driver_info when populating
information about linked nodes, which makes it easier to later get
the devices created. In this context, reimplement functions like
clk_get_by_index_platdata() which made use of the previous approach.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently when using OF_PLATDATA the binding between devices and drivers
is done trying to match the compatible string in the node with a driver
name. However, usually a single driver supports multiple compatible strings
which causes that only devices which its compatible string matches a
driver name get bound.
To overcome this issue, this patch adds the U_BOOT_DRIVER_ALIAS macro,
which generates no code at all, but allows an easy way to declare driver
name aliases. Thanks to this, dtoc could be improve to look for the driver
name based on its alias when it populates the U_BOOT_DEVICE entry.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using OF_PLATDATA, the bind process between devices and drivers
is performed trying to match compatible string with driver names.
However driver names are not strictly defined, and also there are different
names used when declaring a driver with U_BOOT_DRIVER, the name of the
symbol used in the linker list and the used in the struct driver_info.
In order to make things a bit more clear, rename the drivers names. This
will also help for further OF_PLATDATA improvements, such as checking
for valid driver names.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fix for sandbox of-platdata to avoid using an invalid ANSI colour:
Signed-off-by: Simon Glass <sjg@chromium.org>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAl76U4wACgkQKPlOlyTy
XBhKeg/6Au6lPC5QLnjEO5gpuhI/eF555jRoABXUNoM8FUjkcqA207Sgd3iTH9lS
imOGHkzwipYno5pY1UoiXr7RKJgAkJfKYWRrZ46qgITrEkgQ8Xyp46xIqhoHvpuH
Qs1YeDllHeRViBt2ZP6UJsYfUIA9xnU/o9tLh4lx2SiCPWbNDns7cB0Ajazh47Cx
8UT2ZwbATaaFfN9m4Lg65O6Fe1G/cHAw5H/xsDajpVOpskHk0RZxRxzob6XLQete
sVkZdjYmH7zG+7THLkPriu2y/qlc5t2re3OeAr/5YwYJODnj3aN7iI20Sl9xMwDP
eDcSt19HMs+Ng60+yqwHxoU+AQ2BjswYHssb2vdY8OQhlRpoFke6nT+oQtCQCYhZ
At/b2O8kh9IM9alsc8xltMABLgrOhREfxC6VQg7bsCH01+qcojGX8dhVQrYsWkKQ
GrCs6SAl8zR78j8s3OGSsvTczMkTrBTglYWIYrlvA5fFhVg5Yz38S+ioTqPc4QDc
ZJ9bDDO00CY4hJC8sx4TQcsn0OmSJeN394dy6CUoxL6fEXBdRmNRLBUnmuTmPmYT
suLB9qaG+Q6cEttXjfNN1VotSG+61COUZ0uoed47cGUo8AxLMTEe62twUc0aDPNS
NMUoMwHqVbivaGUBfG16mu8bnVfaCqFyR/LLGa6J3yQSQ8qeu30=
=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
Add missing space before a comment delimiter.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
SDHCI HISPD bits need to be configured based on desired mmc
timings mode and some HISPD quirks.
So, handle the HISPD bit based on the mmc computed selected
mode(timing parameter) rather than fixed mmc card clock
frequency.
Linux handle the HISPD similar like this in below commit but no
SDHCI_QUIRK_BROKEN_HISPD_MODE,
commit <501639bf2173> ("mmc: sdhci: fix SDHCI_QUIRK_NO_HISPD_BIT handling")
This eventually fixed the mmc write issue observed in
rk3399 sdhci controller.
Bug log for refernece,
=> gpt write mmc 0 $partitions
Writing GPT: mmc write failed
** Can't write to device 0 **
** Can't write to device 0 **
error!
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Peng Fan <peng.fan@nxp.com>
Peng Fan: added back "ctrl &= ~SDHCI_CTRL_HISPD;" per Jaehoon's suggestion
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> # roc-rk3399-pc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
According to eMMC specification v5.1 section 6.4.3, we should issue
CMD1 repeatedly in the idle state until the eMMC is ready even if
mmc_send_op_cond() send CMD1 with argument = 0. Otherwise some eMMC
devices seems to enter the inactive mode after mmc_complete_op_cond()
issued CMD0 when the eMMC device is busy.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In current code, we add 1ms dealy after each tuning command for standard
tuning method. Adding this 1ms dealy is because USDHC default check the
CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning
IC logic do not wait for the tuning data sending out by the card, trigger
the buffer read ready interrupt immediately, and step to next cycle. So
when next time the new tuning command send out by USDHC, card may still
not send out the tuning data of the upper command，then some eMMC cards
may stuck, can't response to any command, block the whole tuning procedure.
If do not check the CMD CRC for tuning, then do not has this issue. USDHC
will wait for the tuning data of each tuning command and check them. If the
tuning data pass the check, it also means the CMD line also okay for tuning.
So this patch disable the CMD CRC check for tuning, save some time for the
whole tuning procedure.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
We only call the function omap_hsmmc_get_cfg in the case of OMAP34XX or
when we have to iodelay recalibration. Add guards for these checks as
clang will otherwise warn.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Unsupported voltage on voltage switch is not an error, do not
print error message in such a case. This happens e.g. if the
eMMC is already in 1V8 mode or when testing 1V2 mode operation
on systems which only do 3V3/1V8 switching.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The 3V3/1V8 switching could never have worked on any of the iMXes
ever since 51313b49f2 ("mmc: fsl_esdhc: support SDR104 and HS200"),
because that commit uses priv->vqmmc_dev when switching voltages on
mode switch, while local vqmmc_dev in probe to store the regulator
pointer. Those are two different variables with the same name. So
the priv->vqmmc_dev was always NULL and thus voltage switch between
modes never really suceeded.
Fix this by assigning priv->vqmmc_dev with value of the vqmmc_dev
in probe.
Fixes: 51313b49f2 ("mmc: fsl_esdhc: support SDR104 and HS200")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- Rename DT compatible name
- Remove uneccessary if-statement to support 8-bit buswidth
- Remove redundant error msg
- Use symbolic constants in switch statement
Signed-off-by: Arthur Li <arthur.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Tom Rini <trini@konsulko.com>
When eSDHC operates at 3.3v, damage can accumulate in an internal
level shifter at a higher than expected rate. The faster the interface
runs, the more damage accumulates. This issue now is found on LX2160A
eSDHC1 for only SD card.
The hardware workaround is recommended to use an on-board level shifter
that is 1.8v on SoC side and 3.3v on SD card side.
For boards without hardware workaround, this option could be enabled,
ensuring 1.8v IO voltage and disabling eSDHC if no card.
This option assumes no hotplug, and u-boot has to make all the way to
to linux to use 1.8v UHS-I speed mode if has card.
If you do not want the workaround for better user experience, of course
you can choose to not select it running eSDHC in unsafe mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Cleanup this driver to use dt in U-boot and static platdata in SPL.
This requires the following steps:
1. Move all platdata assignment from probe() to ofdata_to_platdata().
This function is only called in U-boot.
2. Replicate all the platdata assignment being done in
ofdata_to_platdata() in the omapl138 board file. This data is used in
the SPL case where SPL_OF_CONTROL is not enabled.
3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl69FWMACgkQ4rK92eCq
k3Vy9wgAmFLZ+u2C87A9Cs8i73QX/hs9TsjTJJPxsQWy3bOILgw8ZqBtzqD0qPvc
Mpqq7UEIZ17OW/lZCi3hqC0nGj7bT3N9rDpUQfu5Voq3GoO80yZqvCQU04AXGGpW
Aj0fjI5a6JRxQfR7XVoNw7UXPDUrDlchvBDR1GMK4cj4Sw/B+pXNDjkoJ1UWbxG6
INDgQQKhOCdMzbIsMLiUe4zkT6E8ADI0eJzgti3kWBzrdkwXZg40iEJu/MbMPRKE
Y22QZ6EkEMFTVYeCPXLU8keo4UbBIKDXWmVDbDeDbNa0QrKZ2IZ0TijajWeMWxZV
Q9J7JgpSchWcVB14vYNx+HXPUHANTA==
=bhlu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200514' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- stm32mp1: migrate MTD and DFU configuration in Kconfig
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
Change the mmc displayed name in U-Boot for stm32_sdmmc2 driver to
“STM32 SD/MMC”.
This stm32_sdmmc2 driver is for version 2 of the ST HW IP SDMMC but the
displayed name "STM32 SDMMC2" is confusing for user, between the
instance of SDMMC and the device identifier of MMC.
For example on EV1 board, we have:
STM32MP1> mmc list
STM32 SDMMC2: 0 (SD)
STM32 SDMMC2: 1 (eMMC)
Changed to more clear:
STM32MP1> mmc list
STM32 SD/MMC: 0 (SD)
STM32 SD/MMC: 1 (eMMC)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
If CONFIG_MMC_SDHCI_SDMA is enabled but the HW could not support it,
we no longer error out. Instead we do not enable it in the host.
Change the output from printf to debug as this isn't an error but only
additional information now.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
If Host controller doesn't support SDMA, it doesn't need to return
error. Because it can be worked with PIO mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Use phys2bus macro when dma address is accessed.
Some targets need to use pyhs2bus macro. (e.g, RPI4)
After applied it, SDMA mode can be used.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Currently, the entry "bus-width = <8>" in the ZynqMP's sdhci nodes
is not evaluated. This results in the bus width staying at its default
value (4 bit in HS200 mode).
Fix this by calling mmc_of_parse. This function also checks for the
"no-1-8-v" and "max-frequency" entries. Remove the handling of those
nodes from this driver.
Signed-off-by: Benedikt Grassl <Benedikt.Grassl@rohde-schwarz.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This function does not modify the device to change it to use const *, so
that callers with a const udevice * can call it without a cast.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
RPMB support is used by the 'mmc rpmb' command and by the OP-TEE support.
We do not need it in SPL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implement get_b_max() for the Renesas R-Car SDHI controller driver, limit
the b_max per hardware capabilities such that select Gen2 controllers have
16bit block transfer limit, the rest has 32bit block transfer limit and on
Gen3, the block transfer limit on addresses above the 32bit boundary is set
to 1/4 of the malloc area.
Originally, on Gen3, the block transfers above the 32bit area were limited
to PIO only, which resulted in (R8A7795 Salvator-X , HS200 eMMC):
=> time mmc read 0x0000000700000000 0 0x10000
time: 0.151 seconds
=> time mmc read 0x0000000700000000 0 0x100000
time: 11.090 seconds
with bounce buffer in place and b_max adjustment in place:
=> time mmc read 0x0000000700000000 0 0x10000
time: 0.156 seconds
=> time mmc read 0x0000000700000000 0 0x100000
time: 2.349 seconds
Note that the bounce buffer does mallocate and free the bounce buffer
for every transfer. Experiment which removes this results in further
increase of read speed, from 2.349s to 2.156s per 512 MiB of data,
which is not such a significant improvement anymore. It might however
be interesting to have bounce buffer directly in the MMC core or even
block core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Add getter function which permits adjusting the maximum number of
blocks that could be read in a single sustained read transfer based
on the location of the source/target buffer and length, before such
transfer starts.
This is mainly useful on systems which have various DMA restrictions
for different memory locations, e.g. DMA limited to 32bit addresses,
and where a bounce buffer is used to work around such restrictions.
Since the U-Boot bounce buffer is mallocated, it's size is limited
by the malloc area size, and the read transfer to such a buffer must
also be limited. However, as not all areas are limited equally, the
b_max should be adjusted accordinly as needed to avoid degrading
performance unnecessarily.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The R-Car SDHI DMA controller has various restrictions. To work around
those restrictions without falling back to PIO, implement bounce buffer
with custom alignment check function which tests for those limitations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
set_ios_post return type changed from void to int, correcting
the same to fix compilation warning.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Provide command 'mmc wp' to power on write protect boot areas on eMMC
devices.
The B_PWR_WP_EN bit in the extended CSD register BOOT_WP is set. The boot
area are write protected until the next power cycle occurs.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In R-Car Gen 3, there is a DMA controller restriction of SDHI.
When the transfer exceeding the 4 kByte boundary is performed while
the DRAM address is not 128 byte aligned, the bus is occupied.
This patch avoids this.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Until now, the mmc clock was left in a good enough state by the ROM
code to be used by the controller. However on some SoC, if the ROM
code finds a bootloader on USB or SPI, it might leave the MMC clock
in state the controller cannot work with.
Enable the input clocks provided to the mmc controller. While the
u-boot mmc controller driver is not doing fancy settings like the Linux,
it at least needs to make these clocks are running.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
According to the HW team, for some reason the normal clock select code
picks what appears to be a perfectly valid 375KHz SD card clock, based
on the CAR clock source and SDMMC1 controller register settings (CAR =
408MHz PLLP0 divided by 68 for 6MHz, then a SD Clock Control register
divisor of 16 = 375KHz). But the resulting SD card clock, as measured by
the HW team, is 700KHz, which is out-of-spec. So the WAR is to use the
values given in the TRM PLLP table to generate a 400KHz SD-clock (CAR
clock of 24.7MHz, SD Clock Control divisor of 62) only for SDMMC1 on
T210 when the requested clock is <= 400KHz. Note that as far as I can
tell, the other requests for clocks in the Tegra MMC driver result in
valid SD clocks.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
As per the T210 TRM, when running at 3.3v, the SDMMC1 tap/trim and
autocal values need to be set to condition the signals correctly before
talking to the SD-card. This is the same as what's being done in CBoot,
but it gets reset when the SDMMC1 HW is soft-reset during SD driver
init, so needs to be repeated here. Also set autocal and tap/trim for
SDMMC3, although no T210 boards use it for SD-card at this time.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The 4 bit MMC controllers have an internal debounce for the SDCD line
with a debounce delay of 1 second. Therefore, after clocks to the IP are
enabled, software has to wait for this time before it can power on the
controller.
Add a deferred_probe() callback which polls on sdcd for a maximum of 2 seconds
before switching on power to the controller or (in the case of no card)
returning a ENOMEDIUM. This pushes the 1 second wait time to when the
card is actually needed rather than at every probe() making sure that
users who don't insert an SD card in the slot don't have to wait such a
long time.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
With the latest RIOT, there is a different otap delay value for each
speed mode. Add a new binding with every supported speed mode. Also
disable a given speed mode in the host caps if its corresponding
otap-del-sel is not present.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
MMC_LEGACY & SD_LEGACY are not differentiated timings in the spec and
don't have any meaningful differences. Therefore, get rid of all
references to SD_LEGACY and use MMC_LEGACY to mean both of them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add the sdhci_deferred_probe() function to register as the
deferred_probe() callback to the mmc core. It will in turn call the
deferred_probe() callback of the platform drivers as declared in the
sdhci_ops.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add a deferred_probe() API for platforms that want to do some
configurations just before starting to enumerate the device.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Initial DesignWare based DM support for Cortina Access CAxxxx SoCs.
Signed-off-by: Arthur Li <arthur.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
This driver currently performs cache operation before the DMA start,
but does nothing after the DMA completion.
When reading data by DMA, the cache invalidation is needed also after
finishing the DMA transfer. Otherwise, the CPU might read data from
the cache instead of from the main memory when speculative memory read
or memory prefetch occurs.
Instead of calling the cache operation directly, this commit adds
dma_unmap_single(), which performs cache invalidation internally,
but drivers do not need which operation is being run.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, sdhci_prepare_dma() calls flush_cache() regardless of the
DMA direction.
Actually, cache invalidation is enough when reading data from the device.
This is correctly handled by dma_map_single(), which mimics the DMA-API
in Linux kernel. Drivers can be agnostic which cache operation occurs
behind the scene.
This commit also sanitizes the difference between the virtual address
and the dma address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
host->mmc is already (struct mmc *).
memalign() returns an opaque pointer, so there is no need for casting.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use {lower,upper}_32_bits() instead of the combination of cast
and shift.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The same code is run for both SDHCI_QUIRK_32BIT_DMA_ADDR and
define(CONFIG_FIXED_SDHCI_ALIGNED_BUFFER).
Unify the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Using the global variable does not look nice.
Add a new field sthci::align_buffer to point to the bounce buffer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.
Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.
If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.
Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The reference manuals for MPC8308 and MPC8309 both say that the
esdhcctl aka DMA Control Register "is implemented as SDHCCR" in the
System configuration registers. Unfortunately, that doesn't mean that
the registers are just mirrors of each other - any write to esdhcctl
is simply ignored. So to actually enable cache snooping, we
unfortunately have to add a little ifdeffery.
There is, naturally, no description of the bit fields of esdhcctl in
the MPC8309 manual, but comparing the description of esdhcctl from the
LS1021A reference manual to the description of the sdhccr in MPC8309,
one also finds that the fields are bit-reversed, so the bit to set is
0x02000000 rather than 0x00000040 - this is also what board_mmc_init()
uses in the two gdsys/mpc8308/ boards.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
These functions are defined before the callers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since commit 01298da31d ("mmc: Change mode when switching to a boot
partition"), errors in mmc_select_mode_and_width() are ignored.
The return value should be checked.
Fixes: 01298da31d ("mmc: Change mode when switching to a boot partition")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cadence sent out an errata report to their customers of this IP.
This errata is not so severe, but the tune request should be sent
twice to avoid the potential issue.
Quote from the report:
Problem Summary
---------------
The IP6116 SD/eMMC PHY design has a timing issue on receive data path.
This issue may lead to an incorrect values of read/write pointers of
the synchronization FIFO. Such a situation can happen at the SDR104
and HS200 tuning procedure when the PHY is requested to change a phase
of sampling clock when moving to the next tuning iteration.
Workarounds
-----------
The following are valid workarounds to resolve the issue:
1. In eMMC mode, software sends tune request twice instead of once at
each iteration. This means that the clock phase is not changed on
the second request so there is no potential for clock instability.
2. In SD mode, software must not use the hardware tuning and instead
perform an almost identical procedure to eMMC, using the HRS34 Tune
Force register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
erase_grp_size is used, when MMC_WRITE is enabled.
- error: ‘struct mmc’ has no member named ‘erase_grp_size’
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
If the host has Broken R1B, use only R1 response type.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Drop local dma_map_single() and dma_unmap_single() and use arch specific
common implementation
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Read generic MMC properties from device-tree. This allows to specify for
example cd-inverted property and let MMC core to properly handle such
case.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
Add Support for writing to PHY registers for J721e. There are number of
differences between the J721e 8 bit PHY, J721e 4 bit PHY and AM654 PHY.
Create a driver_data structure with an ops and flags field and use the
flags field to indicate these differences. The differences are as
follows:
1. The J721e 4 bit instance PHY does not have a DLL. Introduce a
DLL_PRESENT flag to make sure that DLL related registers are accessed
only where they are present. Also add a separate set_ios_post()
callback.
2. The J721e 8 bit instance is not muxed with anything else inside the
SoC and hence the IOMUX_ENABLE filed does not exist. Add a flag which is
used to indicate the presence of this field.
3. The register field used to select DLL frequency is 3 bit wide in
J721e as compared to 2 bits in AM65x. Add another flag that
distinguishes these fields.
4. The strobe select field is 8 bit wide as compared to 4 bit wide for
AM65x. Add yet another flag to indicate this difference. Strobe select
is used only for HS400 speed mode, support for which has not been added
in AM65x.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Get clk_xin by name instead of by index to avoid having to put clocks in
the same order in all devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch add mmc and sd support for Mediatek MT7622 SoCs
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
For CMD21 tuning data, the 128/64 bytes data may coming in very
short time, before msdc_start_data(), the read data has already
come, in this case, clear MSDC_INT will cause the interrupt disappear
and lead to the thread hang.
the solution is just clear all interrupts before command was sent.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
This patch adds mmc support for MediaTek MT8512/MT8110 SoCs.
MT8512/MT8110 SoCs puts the tune register at top layer, so
need add new code to support it.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
It was observed (on ClearFog Base) that sending MMC APP_CMD returned
an error on the first attempt. The issue appears to be timing related
since even inserting a puts() short debug entry before the execution
added sufficient delay to receive success on first attempt.
Follow the existing quirks pattern to retry if initial issuance
failed so as to not introduce any delay unless needed.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
The eSDHC reference clocks should be provided by speed.c in arch/.
And we do not need CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK option to
select which clock to use. Because we can make the driver to select
the periperhal clock which is better (provides higher frequency)
automatically if its value is provided by speed.c.
This patch is to drop this option and make driver to select clock
automatically. Also fix peripheral clock calculation issue in
fsl_lsch2_speed.c/fsl_lsch3_speed.c.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The fdt fixup for properties "peripheral-frequency" and "adapter-type"
was once for a Freescale SDK release. The properties haven't been existed
in linux mainline. Drop these useless code.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Add compatible "fsl,imxrt-usdhc" to make mmc working on i.MXRT platforms
with CONFIG_DM_MMC=y.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Not all architectures(i.e. i.MXRT) support mxc_get_clock() and use DM_CLK
instead. So building could result in failure due to missing
mxc_get_clock().
Make if(CONFIG_IS_ENABLED(CLK)) an #if statement.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
When no GPIO is used to read the card detect status the following
error is seen:
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... MMC: no card present
*** Warning - No block device, using default environment
Fix it by handling the "broken-cd" property in the same way
that drivers/mmc/sdhci.c does, which considers that the SD card
is present when the "broken-cd" property is passed.
Tested on a imx6ul-evk board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Convert clock manager for Gen5, Arria 10 and Stratix 10 from struct
to defines.
Change to get clock manager base address from DT node instead of using
#define.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert system manager for Gen5, Arria 10 and Stratix 10 from struct
to defines.
Change to get system manager base address from DT node instead of
using #define.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
Adam Ford reports that this change breaks booting on da850-evm and
Bartosz Golaszewski agrees that with the impending release we should
revert the change for now. With that noted:
This reverts commit 21a4d80a71.
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The MMC boot is currently broken on omapl138-lcdk after enabling the
driver model in SPL. The main problem is the driver's bind callback not
being called after probe in SPL (even with the DM_FLAG_PRE_RELOC flag
specified).
While a proper fix is still being worked on, this hacky changeset at
least fixes the MMC boot on this platform by calling mmc_bind()
manually from probe().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
struct mmc_config & struct mmc don't need to be exported over platform
data, but can instead be private in the driver.
Remove struct davinci_mmc_plat.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The DM family of DaVinci SoCs is no longer supported. Drop the
irrelevant code from the driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using single fixed value for the calibration offset,
add tables which dynamically adjust this per calibration code
from the SCC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Some of the tuning taps produce suboptimal results. Add code
which skips those "bad" taps.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Check SCC for errors after check command if applicable and
optionally adjust the bus skew settings accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Disable the auto-retuning in HS400 mode in favor of manual calibration.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Adjust the TMPPORT3 offsets according to the latest information
from the chip vendor.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Adjust the DT2FF offsets in HS400 according to latest information
from the chip vendor.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The M3W up to ES1.2 uses 4 tuning taps for HS400, make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Retain the SMPCMP value from last calibration in private data.
This will be later used for skipping bad taps.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Retain the tap number from last calibration in private data. This
will be later used for SCC error checking after each command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch is to get clock directly from global data.
- Remove uclass clk api method. This was what i.MX platforms were
using, while QorIQ platforms weren't.
- Get clock only from global data, dropping mxc_get_clock().
QorIQ eSDHC controllers on one silicon use same reference clock.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Rockchips dwmmc controllers can't do dma to non-ddr addresses,
like for example the soc-internal sram but during boot parts of
TrustedFirmware need to be placed there from the read FIT image.
So add handling for a u-boot,spl-fifo-mode to not put the mmc
controllers into fifo mode for all time.
The regular fifo-mode property still takes precedent and only
if not set do we check for the spl-specific property.
Suggested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To enable HS400(ES) and UHS for imx8m platforms, update the driver data
to share with imx8qm esdhc_soc_data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
During mmc initialization, there are several calls to mmc_set_clock
and mmc_set_ios. When mmc_power_off, the mmc->clock will be set,
but the imx driver will use 400KHz. So the following calls
to mmc_set_ios will set the clock several times which is redundant
in fsl_esdhc_imx driver. So let's simplify to remove redundant
clock settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The QorIQ eSDHC on all platforms supports checking write protect
state through register bit. So check it always.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The fsl_esdhc_init() was actually to get configuration of mmc_config.
So rename it to fsl_esdhc_get_cfg_common() and make it common for both
DM_MMC and non-DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to clean up bus width setting code.
- For DM_MMC, remove getting "bus-width" from device tree.
This has been done in mmc_of_parse().
- For non-DM_MMC, move bus width configuration from fsl_esdhc_init()
to fsl_esdhc_initialize() which is non-DM_MMC specific.
And fix up bus width configuration to support only 1-bit, 4-bit,
or 8-bit. Keep using 8-bit if it's not set because many platforms
use driver without providing max bus width.
- Remove bus_width member from fsl_esdhc_priv structure.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Voltage validation should be done by CMD8. Current comparison between
mmc_cfg voltages and host voltage capabilities is meaningless.
So drop current comparison and let voltage validation is through CMD8.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Controller initialization is not needed in fsl_esdhc_init().
It will be done in esdhc_init() for non-DM_MMC, and in
esdhc_init_common() in probe for DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
A previous patch below adding DDR mode support was actually for i.MX
platforms. Now i.MX eSDHC driver is fsl_esdhc_imx.c. For QorIQ eSDHC,
it uses different process for DDR mode, and hasn't been supported.
Let's drop DDR support code for i.MX in fsl_esdhc driver.
0e1bf61 mmc: fsl_esdhc: Add support for DDR mode
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
U-boot prefers DM_MMC + BLK for MMC. Now eSDHC driver has already
support it, so let's force to use it.
- Drop non-BLK support for DM_MMC introduced by below patch.
66fa035 mmc: fsl_esdhc: fix probe issue without CONFIG_BLK enabled
- Support only DM_MMC + BLK (assuming BLK is always enabled for DM_MMC).
- Use DM_MMC instead of BLK for conditional compile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch adds a dts property cd-active-high for builtin-cd mode to make
it configurable instead of using hardcoded active-low.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
- Add sdhci driver for Broadcom iProc platform
- Add a driver callback for power-cycle for mmc
- Implement host_power_cycle callback for stm32_sdmmc2
- spl: dm_mmc: Initialize only the required mmc device
Power-domain is enabled by default in device_probe. am654 mmc driver
is enabling power-domain again in probe. As the second call is
redundant, drop power_domain_on from probe.
Tested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
For the correct power cycle sequence with stm32_sdmmc2, the write of the
power cycle value in PWRCTL field of SDMMC_POWER register is now done in
stm32_sdmmc2_host_power_cycle() and no more in stm32_sdmmc2_pwrcycle().
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Some MMC peripherals require specific power cycle sequence, where some
registers need to be written between the regulator is turned off and then
back on. This is the case for the MMC IP embedded in STM32MP1 SoC.
In STM32MP157 reference manual [1], the power cycle sequence is:
1. Reset the SDMMC with the RCC.SDMMCxRST register bit. This will reset
the SDMMC to the reset state and the CPSM and DPSM to the Idle state.
2. Disable the Vcc power to the card.
3. Set the SDMMC in power-cycle state. This will make that the
SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are driven low, to prevent the card
from being supplied through the signal lines.
4. After minimum 1ms enable the Vcc power to the card.
5. After the power ramp period set the SDMMC to the power-off state for
minimum 1ms. The SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are set to
drive “1”.
6. After the 1ms delay set the SDMMC to power-on state in which the
SDMMC_CK clock will be enabled.
7. After 74 SDMMC_CK cycles the first command can be sent to the card.
The step 3. cannot be handled by the current framework implementation.
A new callback (host_power_cycle) is created, and called in
mmc_power_cycle(), after mmc_power_off().
The incorrect power cycle sequence has shown some boot failures on
STM32MP1 with some SD-cards, especially on cold boots when the input
frequency is low (<= 25MHz).
Those failures are no more seen with this correct power cycle sequence.
[1] https://www.st.com/resource/en/reference_manual/DM00327659.pdf
Signed-off-by: Yann Gautier <yann.gautier@st.com>
In SPL, all the available mmc devices gets initialized during boot.
This might not work in cases where clocks are not available for
certain mmc devices(other than boot device) and the support for
enabling device might not be ready.
Texas Instruments' K3 J721E device having a central system controller
(dmsc) is one such example falling in this category. Below is the
sequence for the failing scenario:
- ROM comes up in SD mode and loads SPL by just initialing SD card.
- SPL loads dmsc firmware from SD Card.
Since ROM has enabled SD, SPL need not enable the SD, just need
to re initialize the card. But SPL is trying to initialize other MMC
instances which are in disabled state. Since dmsc firmware is not yet
available, devices cannot be enabled. So in SPL, initialize only the
mmc device that is needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
- Rename existing FSP code to fsp1
- Add fsp2 directory in preparation to support FSP 2.0
- Various x86 platform codes update
- Various bug fixes and updates in dm core, sandbox and spl
This change replaces printf() with debug() for the notification about
commands timeouts.
This is done on purpose (also other drivers use such approach - dw_mmc.c,
mvebu_mmc.c), as the mmc core code (mmc.c) uses timeouts to assess if one
is using sd card or eMMC device.
In such situation timeout is a some kind of a "normal" behavior and there
shall not be any output to the console.
There is no impact on boot time for boards using this driver (even in SPL)
when two extra timeouts are returned (no SD card present, only eMMC
available).
Boot time tested with grabserial:
sudo grabserial -b 115200 -d /dev/ttyUSB1 -e 30 -t -m "^U-Boot SPL*"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch converts the mxsmmc driver to support DM/DTS.
Moreover, it is also possible to use it in early SPL with
SPL_OF_PLATDATA enabled.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The zynq_sdhci drivers depends on DM_MMC in Kconfig so no need to check for
DM_MMC in the driver so this patch removes it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present there is only one control for this and it is used for both SPL
and TPL. But SPL might have a lot more space than TPL so the extra cost of
a full printf() might be acceptable.
Split the option into two, providing separate SPL and TPL controls. The
TPL setting defaults to the same as SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present running sandbox with valgrind produces some warnings due to the
MMC emulator not filling in all the expected fields. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: use sizeof() instead of hardcoded 16]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add eMMC hs200 mode for ls1028a, ls1012a, lx2160a.
This increases eMMC performance.
Tuning procedure is currently not supported.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
NXP fsl_esdhc controller supports two reference clocks:
platform clock and peripheral clock
Peripheral clock can provide higher clock frequency
which is required to be used for tuning of SD UHS mode
and eMMC HS200/HS400 modes.
Peripheral clock is enabled by default by defining config
option FSL_ESDHC_USE_PERIPHERAL_CLK if eMMC HS200/HS400 modes
are supported.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
-----BEGIN PGP SIGNATURE-----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=hWTf
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2019.10' of https://github.com/mbgg/u-boot
- fix mailbox status register used for polling
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
The bcm2711 has two emmc controllers. The difference is the clocks
they use. Add support for the second emmc controller.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Andrei Gherzan <andrei@balena.io>
Function bcm_2835_wait_transfer_complete() is not waiting long enough.
The previous code was claiming to wait for ~1 seconds, but as it depends
on register reads it's time actually varies.
Some cards require wait times of up to ~56 ms to perform
the command 'saveenv' on an EXT4 partition.
Re-implement the loop exit condition to use get_timer() which allows
to specify the wait time in more reliable manner. Set the maximum wait
time to the originally intended 1 second.
Signed-off by: Raul Benet <raul.benet_at_kaptivo.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The sdhci capabilities registers can be incorrect. The
sdhci-caps-mask and sdhci-caps dt properties specify which bits of
the registers are incorrect and what their values should be. This
patch makes the sdhci driver use those properties to correct the caps.
Also use "dev_read_u64_default" instead of "dev_read_u32_array" for
caps mask.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The mmc_spi driver's priv is not available in its bind phase(). Use
platdata instead.
Fixes: 05e35d4297 ("mmc: mmc_spi: Re-write driver using DM framework")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There are two cases not been considered:
- use uint for timeout, it will overflow when size bigger than 512KB for
it *8*1000 at the beginning, but we may use size up to 32MB; The
'timeout' will overflow if size bigger than 51.2MB after this fix, which
should be enough for U-Boot;
- The timeout is using clock speed for data rate, but the device may not
have such high speed, eg. clock is 52MHz while the device write speed may
be less than 10MB/s, and we may use up to 150MHz clock.
Fix them in this patch, the max timeout is about 6500 when size is 32MB
after fix.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
It's quite hard to figure out time units for various function that have
timeout parameters. This leads to possible errors when one forgets to
convert ms to us, for example. Let's rename those parameters
correspondingly to 'timeout_us' and 'timeout_ms' to prevent such issues
further.
While at it, add time units info as comments to struct mmc fields.
This commit doesn't change the behavior, only renames parameters names.
Buildman should report no changes at all.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
mmc_wait_dat0() expects timeout argument to be in usec units. But some
overlying functions operate on timeout in msec units. Convert timeout
from msec to usec when passing it to mmc_wait_dat0().
This fixes 'avb' commands on BeagleBoard X15, because next chain was
failing:
get_partition() -> mmc_switch_part() -> __mmc_switch() ->
mmc_wait_dat0()
when passing incorrect timeout from __mmc_switch() to mmc_wait_dat0().
Fixes: bb98b8c5c0 ("mmc: During a switch, poll on dat0 if available and check the final status")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
When look through the code, I found this bare metal
drives is not used, so remove it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
eMMC device has multiple hw partitions both address from zero. However the
mmc driver lacks block cache invalidation for switch hwpart. This causes a
problem that data of current hw partition is cached before switching to
another hw partition. And the following read operation of the latter hw
partition will get wrong data when reading from the addresses that have
been cached previously.
To solve this problem, invalidate block cache after a successful
mmc_switch_part() operation.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tested-by: Felix Brack <fb@ltec.ch>
This patch solves a watchdog reset issue during mmc erase command.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
host->mmc, host->mmc->dev and host->mmc->priv must be set
before calling sdhci_setup_cfg() to avoid hang during mmc
initialization.
Thanks to commit 3d296365e4
("mmc: sdhci: Add support for sdhci-caps-mask") which put
this issue into evidence.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Increase SDMMC_BUSYD0END_TIMEOUT_US from 1s to 2s to
avoid timeout error during blocks erase on some sdcard
Issue seen on Kingston 16GB :
Device: STM32 SDMMC2
Manufacturer ID: 27
OEM: 5048
Name: SD16G
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
card capabilities: widths [4, 1] modes [SD Legacy, SD High Speed (50MHz)]
host capabilities: widths [4, 1] modes [MMC legacy, SD Legacy, MMC High Speed (26MHz), SD High Speed (50MHz), MMC High Speed (52MHz)]
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 14.5 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
Issue reproduced with following command:
STM32MP> mmc erase 0 100000
MMC erase: dev # 0, block # 0, count 1048576 ... mmc erase failed
16384 blocks erased: ERROR
By setting SDMMC_BUSYD0END_TIMEOUT_US at 2 seconds and by adding
time measurement in stm32_sdmmc2_end_cmd() as shown below:
+start = get_timer(0);
/* Polling status register */
ret = readl_poll_timeout(priv->base + SDMMC_STA,
status, status & mask,
SDMMC_BUSYD0END_TIMEOUT_US);
+printf("time = %ld ms\n", get_timer(start));
We get the following trace:
STM32MP> mmc erase 0 100000
MMC erase: dev # 0, block # 0, count 1048576 ...
time = 17 ms
time = 1 ms
time = 1025 ms
time = 54 ms
time = 56 ms
time = 1021 ms
time = 57 ms
time = 56 ms
time = 1020 ms
time = 53 ms
time = 57 ms
time = 1021 ms
time = 53 ms
time = 57 ms
time = 1313 ms
time = 54 ms
time = 56 ms
time = 1026 ms
time = 54 ms
time = 56 ms
time = 1036 ms
time = 54 ms
time = 56 ms
time = 1028 ms
time = 53 ms
time = 56 ms
time = 1027 ms
time = 54 ms
time = 56 ms
time = 1024 ms
time = 54 ms
time = 56 ms
time = 1020 ms
time = 54 ms
time = 57 ms
time = 1023 ms
time = 54 ms
time = 56 ms
time = 1033 ms
time = 53 ms
time = 57 ms
....
time = 53 ms
time = 57 ms
time = 1021 ms
time = 56 ms
time = 56 ms
time = 1026 ms
time = 54 ms
time = 56 ms
1048576 blocks erased: OK
We see that 1 second timeout is not enough, we also see one measurement
up to 1313 ms. Set the timeout to 2 second to keep a security margin.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This converts the following to Kconfig:
CONFIG_FSL_USDHC
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list]
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit adds MMC driver support for HI3660 SoC reusing hi6220_dw_mmc
driver. Since HI3660 operates at different clock rate and uses fifo
mode now, let's introduce the platform data and utilize it for different
SoCs supported by this driver.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This is a configuration option specific to the tegra controller.
Doing it this way makes it show up directly under the tegra controller
option, indented one level, as "Disable external clock loopback".
The way it is now, it shows up at the end of the controller list, not
indented, as if it's some kind of generic MMC configuration option.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Add rk3399 boards Khadas Edge/-V/-Captain
- Add fully souce code support for rk3328 including TPL/DRAM init
- Enable boot from eMMC for rk3399 rock960/ficus boards
- turn on the IO supply for dw_mmc
Commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Since commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field. Move the mmc field initialization before sdhci_setup_cfg()
call to avoid crash on mmc pointer dereference.
[this patch is based on commit 41a9fab8da ("mmc: mv_sdhci: fix
uninitialized pointer deref on probe") by Baruch Siach]
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu102/zc706)
Select SPL_HS200_SUPPORT if SPL_HS400_SUPPORT is selected as is being
done for the U-boot case.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The comment about init op being NULL used to be next to the NULL check
code. Commit 8ca51e51c1 ("dm: mmc: Add a way to use driver model for
MMC operations") separated the comment from the code. Put them back
together.
Fixes: 8ca51e51c1 ("dm: mmc: Add a way to use driver model for MMC operations")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When reading large data in once (reading 512MiB is tested on MT7623), a
watchdog timeout is triggered due to watchdog not being fed.
This patch adds WATCHDOG_RESET() to msdc_start_data() so the watchdog will
be fed every 1024 blocks are read/written.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The standard property name for chip-detect gpio is "cd-gpios". All
in-tree DT files use only this name.
Fixes: 451931ea70 ("mmc: sdhci: Read cd-gpio from devicetree")
Cc: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field. Move the mmc field initialization before sdhci_setup_cfg()
call to avoid crash on mmc pointer dereference.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Fixes the microSD slot on the ASUS C201.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com<mailto:peng.fan@nxp.com>>
The j721e 4 bit instances don't have a hard DLL and therefore don't need
any DLL related configurations. Split the compatibles into an 8 bit and a
4 bit one. Add a private flags field which can be used to check if the
DLL is present and don't register the set_ios_post callback for the 4 bit
compatible instances.
Also update the compatibles in k3-j721e-main.dtsi to avoid breaking boot
with the new compatibles.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch fix mmc driver abort caused by below patch:
3d296365e4 mmc: sdhci: Add support for sdhci-caps-mask
After the patch sdhci_setup_cfg() access to host->mmc->dev,
so we have to do init before make the call to the function()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Most DM based SPI host controller drivers use SPI_XFER_BEGIN and
SPI_XFER_END flags to enable/disable slave chip select.
This patch extends MMC SPI driver to pass SPI_XFER_BEGIN flag when
MMC command is send at start and pass SPI_XFER_END flag using a
dummy transfer (of bitlen = 0) at the end of MMC command.
Suggested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
We would like to use the driver even without power domains being
specified for cases such as during early boot when the required power
domains have already gotten enabled by the SoC's boot ROM and such
explicit initialization is not needed and possible.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a platform specific set_control_reg() callback to help switch to
UHS speed modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The HOST_CONTROL2 register is a part of SDHC v3.00 and not just specific
to arasan/zynq controllers. Add the same to sdhci.h.
Also create a common API to set UHS timings in HOST_CONTROL2.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support in the driver for handling phy specific registers.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The am654_sdhci driver needs to switch the clock off
before disabling its phy dll and needs to re-enable
the clock before enabling the phy again.
Therefore, make the sdhci_set_clock() function accessible
in the am654_sdhci driver.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add Support for masking some bits in the capabilities
register of a host controller.
Also remove the redundant readl() into caps1.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The host controller works perfectly well without having to add any
quirks. Remove them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync the sdhci0 node from kernel. This changes the compatible that is
required to be there in the driver. Change the same for the SD card node
which is not yet supported in kernel. This also syncs the main_pmx0 node
as a side effect.
Also change the name of the driver to match the compatible in kernel.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- mmc spi driver model support
- drop mmc_spi command
- enhanced Strobe mmc HS400 support
- minor mmc bug/fixes and optimization
- omap hsmmc and mvbeu update
- sdhci card detect support
Flash system partition with fastboot will earse the partition firstly
The 600ms timeout will fail on some SD Card. Enlarge it to 5s to make
it works for most of sdcard
Cc: guoyin.chen <guoyin.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement set_enhanced_strobe hook for fsl_esdhc_imx,
,in esdhc_set_timing and esdhc_change_pinstate, also handle HS400_ES.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
