Commit graph

34347 commits

Author SHA1 Message Date
Tudor Laurentiu
8d3eaa9709 powerpc/mpc85xx: use correct dma compatible for several SoCs
Newer qoriq socs have an updated dma ip block with a
different compatible. Let's make sure we use the proper
string so that the dmas get their liodn.
In order to have the means to specify the compatible
string, the liodn setting macros were updated to receive
a new parameter for it.
The following SoCs were changed to use the new compatible:
 T1023/4, T1040, T2080/1, T4240, B4860.

Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:16 -08:00
Shengzhou Liu
10227aaa24 board/t1024qds: add retimer support on t1024qds
Initialize retimer for XFI on t1024qds.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:16 -08:00
Shengzhou Liu
5818643bf4 t1024qds: increase IO drive strength
Increase IO drive strength to fix FCS error on RGMII ports
on T1024QDS.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:16 -08:00
Shengzhou Liu
c18fc2c960 net/phy: enable serdes auto-negotiation for vsc8514 phy
VSC8514 QSGMII PHY requires enabling auto-negotiation,
otherwise it wouldn't work.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:15 -08:00
Shengzhou Liu
355b385847 board/t1024qds: update pin multiplexing
Add multiplexing support among SPI flash, TDM riser card and SDXC.
it routes SPI pins to SPI flash by default.
Route SPI pins to SD slot if "adaptor=sdxc" is set in hwconfig.
Route SPI pins to TDM riser card and do fixup for dts if "pin_mux=tdm"
is set in hwconfig.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:15 -08:00
Shengzhou Liu
cc19c25e27 net/fman: update 10GEC to fit new SoC
fm_standard_init() initializes each 10G port by FM_TGEC_INFO_INITIALIZER.
but it needs different implementation of FM_TGEC_INFO_INITIALIZER on different SoCs.
on SoCs earlier(e.g. T4240, T2080), the notation between 10GEC and MAC as below:
	10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2
on SoCs later(e.g. T1024, etc), the notation between 10GEC and MAC as below:
	10GEC1->MAC1, 10GEC2->MAC2

so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to fit the new SoCs on
which 10GEC enumeration is consistent with MAC enumeration.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:15 -08:00
Shengzhou Liu
48c6f328f0 powerpc/t1024rdb: Add T1024 RDB board support
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.

T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
  - Two 10M/100M/1G RGMII ports on-board
  - one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two  Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
	   Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:15 -08:00
Shengzhou Liu
aba8004818 powerpc/t1024qds: Add T1024 QDS board support
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.

T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
  - Two 10M/100M/1G RGMII ports on-board
  - Three 1G/2.5Gbps SGMII ports
  - Four 1Gbps QSGMII ports
  - one 10Gbps XFI or 10Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
  - Chrontel CH7201 for HDMI connection.
  - TI DS90C387R for direct LCD connection.
  - Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
  - 32-bit RISC controller for flexible support of the communications peripherals
  - Serial DMA channel for receive and transmit on all serial channels
  - Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
	   Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:15 -08:00
Shengzhou Liu
f605079041 powerpc/mpc85xx: Add T1024/T1023 SoC support
Add support for Freescale T1024/T1023 SoC.

The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
  - Three PCI Express 2.0 controllers
- Additional peripheral interfaces
  - One SATA 2.0 controller
  - Two USB 2.0 controllers with integrated PHY
  - Enhanced secure digital host controller (SD/eSDHC/eMMC)
  - Enhanced serial peripheral interface (eSPI)
  - Four I2C controllers
  - Four 2-pin UARTs or two 4-pin UARTs
  - Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0

Differences between T1024 and T1023:
  Feature         T1024  T1023
  QUICC Engine:   yes    no
  DIU:            yes    no
  Deep Sleep:     yes    no
  I2C controller: 4      3
  DDR:            64-bit 32-bit
  IFC:            32-bit 28-bit

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:14 -08:00
York Sun
789b3447c0 driver/ddr/fsl: Add workaround for faulty SPD
Some UDIMMs have faulty SPD with wrong mapping for DQ[36-39].
Using raw card spec in case this error is detected.

Signed-off-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:14 -08:00
Priyanka Jain
2892ec5f43 powerpc/mpc85xx: Update LIODN entries for T1040
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:14 -08:00
Shengzhou Liu
06b3acf184 powerpc/t2080: updating rcw for silicon v1.1
T2080 v1.1 requires different MEM_PLL_RAT from previous v1.0,
and also update core frequency to 1.8GHz for v1.1.
We reserve the support for T2080 v1.0 and enable v1.1 by default.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:14 -08:00
Suresh Gupta
e2544e7a54 B4860QDS: Enable enet port as per fsl_b4860_serdes2 string in hwconfig
In B4860QDS board SerDes2 lanes EFGH either go to SFP or AMC riser card
slot2 so either DTSEC3/DTSEC4 or TGEC1/TGEC2 should be accessible. This
Patch enables DTSEC3/DTSEC4 or TGEC1/TGEC2 on bases of user specified
string fsl_b4860_serdes2:sfp_amc=amc or fsl_b4860_serdes2:sfp_amc=sfp
respectively in hwconfig.

Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:14 -08:00
Shaohui Xie
b24f6d401c powerpc/b4860qds: add workaround for XFI
XFI does not work stable on current board, it's due to heat sink issue,
to make it work stable the board needs additional heat sink, enable two
XFI lanes only. Right now we do not have such an erratum for the issue,
so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it.
The workaround will only be used in XFI protocols and only if the
hwconfig indicates that XFI is prefered.

A new VSC3308 config function is used instead of re-use the original
function, to avoid making the function complex and ugly.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:13 -08:00
Suresh Gupta
cd79e5f414 B4860QDS: Enable SFP or AMC on basis of hwconfig string
SerDes2 lanes EFGH either go to SFP or AMC riser card slot2.
By default AMC will be configured even if no hwconfig is specified.

To enable XFI via SFP use the below hwconfig:
	fsl_b4860_serdes2:sfp_amc=sfp

Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@ffeescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:13 -08:00
Shaohui Xie
90e80dc6b6 powerpc/b4860qds: dtb fixup for xfi
Since xfi has no phy, we delete the property "phy-handle" and use
a "fixed-link" property for a xfi port.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:13 -08:00
Shaohui Xie
89b94d851d powerpc/b4860qds: add xfi support
We need following changes to make xfi work on B4:
1. set cross-point switch VSC3308 to use sfp config when running xfi;
2. add 10G interface check for xfi;
3. set phy address for xfi so the 10G ports can be registered by mdio;

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:13 -08:00
Shaveta Leekha
8c328c21b7 B4860: Add alternate LC VCO serdes protocols support in board file
Add the support of newly added LC VCO SerDes protocols
for configuration of IDT and VSC crossbar

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:12 -08:00
Shaveta Leekha
f1d8074c08 B4860QDS: SGMII related updates
- Enable SGMII support for 0x8d Serdes 2 protocol.
    - Correct Phy address for DTSECx for 0x8d/0xb2 Serdes 2 protocol.
    - Updated debug statement
    - Add Alternate LC VCO protocols(0x8d-->0x8c, 0xb2-->0xb1)
    - Rename onboard PHY address defines for more readability
    - Add these new Defines in B4860QDS.h file

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:12 -08:00
Shaveta Leekha
ffc1a87b91 85xx/b4860: Add alternate serdes protocols for B4860/B4420
Addded Alternate options with LC VCO for following protocols:
0x02 --> 0x01
0x08 --> 0x07
0x18 --> 0x17
0x1E --> 0x1D
0x49 --> 0x48
0x6F --> 0x6E
0x9A --> 0x99
0x9E --> 0x9D

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:12 -08:00
Shaveta Leekha
f7c28aa7ce powerpc/b4860: Enable law creation of MAPLE
B4860, B4440, B4420 and B4220 have MAPLE, so enable law creation
for them only. Remove static LAW creation for MAPLE.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:12 -08:00
vijay rai
2aea661810 powerpc/t104x: Convert to use generic board code
Convert T1040QDS and T1040RDB to use generic board code.

Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:12 -08:00
Shengzhou Liu
9b18e5199e net/phy: Add support for CS4315/CS4340 PHY
Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
  to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
  we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:11 -08:00
York Sun
84baed2a2b driver/ddr/fsl: Adjust timing_cfg_0 to better support two DDR slots
Increase write-to-write and read-to-read turnaround time for two-slot DDR
configurations. Previously only quad-rank and two dual-rank configurations
have this additional turnaround time. A recent test on two single-rank
DIMMs shows the shorter additional turnaround time is also needed.

Signed-off-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:11 -08:00
Chunhe Lan
9a7eeb9c9f powerpc/c29xpcie: Enable configs to use generic board code
Add configs:
  o CONFIG_SYS_GENERIC_BOARD
  o CONFIG_DISPLAY_BOARDINFO
in C29XPCIE config header file to use U-boot generic
board code.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:11 -08:00
Chunhe Lan
fb73572369 powerpc/p1023rdb: Enable configs to use generic board code
Add configs:
  o CONFIG_SYS_GENERIC_BOARD
  o CONFIG_DISPLAY_BOARDINFO
in P1023RDB config header file to use U-boot generic
board code.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:11 -08:00
Tang Yuantian
840a5182a5 mpc85xx/p1022ds: convert to generic board
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:10 -08:00
Heiko Schocher
7c1c581f9c powerpc, muas3001: remove CONFIG_SYS_RAMBOOT
cppcheck reports:

[board/muas3001/muas3001.c:270]: (error) Uninitialized variable: psize

remove the CONFIG_SYS_RAMBOOT define to prevent this error report.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:10 -08:00
Holger Brunck
ab23b9a024 km/km82xx: remove CONFIG_SYS_RAMBOOT
This define is never set in our setup, so we can remove it safely. The
former code causes cppcheck to complain about:
[board/keymile/km82xx/km82xx.c:311]: (error) Uninitialized variable:
psize

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:10 -08:00
Ying Zhang
653c28f377 board/freescale: use generic board architecture for p1010rdb
Use generic board architecture for p1010rdb, tested with NOR
boot on p1010rdb-pb.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:10 -08:00
Shaohui Xie
1ccd94fb97 powerpc/P5040DS: enable SATA support
The define CONFIG_FSL_SATA_V2 is missing, so SATA is not available
in U-boot.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:10 -08:00
Ying Zhang
e838b0c752 board/freescale: use generic board architecture for p1025-twr
Use generic board architecture for p1025-twr, tested with NOR
boot and NAND boot on p1025-twr.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:09 -08:00
Ying Zhang
3ad2737ee3 powerpc/t208xqds: VID support
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:09 -08:00
Zhao Qiang
e7f533cd59 powerpc/mpc85xx: modify erratum A007186
T2080 v1.0 has this errata while v1.1 has fixed
this errata by hardware, add a new function has_errata_a007186
to check the SVR_SOC_VER, SVR_MAJ and SVR_MIN first,
if the sil has errata a007186, then run the errata code,
if not, doesn't run the code.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:09 -08:00
Prabhakar Kushwaha
31530e0b8a board/t104xrdb: Conditional workaround of errata A-008044
Workaround of Errata A-008044 was implemented without errata number and it is
enabled by default. Errata A-008044 is only valid for T1040 Rev 1.0.

So put errata number and make it conditional.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:09 -08:00
Prabhakar Kushwaha
9f074e67f5 powerpc/mpc85xx:Put errata number for T104x NAND boot issue
When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.

Workaround is already in-place.
Put the errata number to adhere errata handling framework.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:08 -08:00
York Sun
1b2af9b4e2 powerpc/t1040qds: Update DDR option
Enable interactive debugging by default. Remove DDR controller interleaving
because this SoC only has one controller. Use auto chip-select interleaving
to detect number of ranks.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Poonam Aggrwal <poonam.aggrwal@freescale.com>
2014-12-05 08:06:08 -08:00
York Sun
14109c7a6a mpc85xx/t2080: Fix parsing DDR ratio for new revision
T2080 rev 1.1 changes MEM_RAT in RCW, which requires new parsing for ratio,
the same way as T4240 rev 2.0.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2014-12-05 08:06:08 -08:00
York Sun
ed9e4e4272 mpc85xx/t208xqds: Adjust DDR timing parameters
Adjust timing for dual-rank UDIMM, verified on M3CQ-8GHS3C0E for speed of
1066, 1333, 1600, 1866MT/s. The 1866 timing is copied to 2133 timing in
case such DIMM comes available.

Also update single-rank 1866 timing. Enable interactive debugging as well.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2014-12-05 08:06:08 -08:00
Shengzhou Liu
2519cb344e powerpc/t2080: add serdes2 protocol 0x2e
Add serdes2 protocol 0x2e.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:07 -08:00
Joakim Tjernlund
bcb60cb9c4 Freescale t104x: Do not exclude SGMII
fman_port_enet_if() tests if FM1_DTSEC2 or FM1_DTSEC4 uses
RGMII or MII and if not returns PHY_INTERFACE_MODE_NONE.
This excludes testing for SGMII further down.

Remove the unconditional "else return PHY_INTERFACE_MODE_NONE"
so SGMII can be tested too.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:07 -08:00
Alison Wang
ed39218238 common: spl: Add interactive DDR debugger support for SPL image
To support interactive DDR debugger, cli_simple.o, cli.o, cli_readline.o,
command.o, s_record.o, xyzModem.o and cmd_disk.o are all needed for
drivers/ddr/fsl/interactive.c.

In current common/Makefile, the above .o files are only produced when
CONFIG_SPL_BUILD is disabled.

For LS102xA, interactive DDR debugger is needed in SD/NAND boot too, and
I enabled CONFIG_FSL_DDR_INTERACTIVE. But according to the current
common/Makfile, all the above .o files are not produced in SPL part
because CONFIG_SPL_BUILD is enabled in SPL part, the following error
will be shown,

drivers/ddr/fsl/built-in.o: In function `fsl_ddr_interactive':
/home/wangh/layerscape/u-boot/drivers/ddr/fsl/interactive.c:1871:
undefined reference to `cli_readline_into_buffer'
/home/wangh/layerscape/u-boot/drivers/ddr/fsl/interactive.c:1873:
undefined reference to `cli_simple_parse_line'
make[1]: *** [spl/u-boot-spl] Error 1
make: *** [spl/u-boot-spl] Error 2

So this patch fixed this issue and the above .o files will be produced
no matter CONFIG_SPL_BUILD is enabled or disabled.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:05:52 -08:00
Gregoire Gentil
956a8bae53 ns16550.c: Fix for ns16550 driver hanging on OMAP4
The same problem that is seen on some OMAP3 is also seen on some OMAP4
so include them in the test in order to prevent some hangs during SPL.

[trini: Re-word commit message, make apply cleanly]
Signed-off-by: Tom Rini <trini@ti.com>
2014-12-04 21:28:32 -05:00
Heiko Schocher
0c331ebcc6 arm, am335x: siemens boards add FIT support
add FIT support and set "boardid" from factoryset records
"DEV/id" and "COMP/ver". "boardid" is used for selecting
which fit configuration gets booted on the board.

Signed-off-by: Heiko Schocher <hs@denx.de>
2014-12-04 21:28:32 -05:00
Heiko Schocher
4ac32b9c4d arm, am335x, siemens: read COMP/ver from factoryset
Signed-off-by: Heiko Schocher <hs@denx.de>
2014-12-04 21:28:32 -05:00
Heiko Schocher
7dc60d81a1 arm, am335x, siemens: fix factoryset interpretation
a record could contain other records, so after an ">" (begin mark)
there not always come an end mark "<", instead a ">" is possible.
Take care of this.

Signed-off-by: Heiko Schocher <hs@denx.de>
2014-12-04 21:28:32 -05:00
Stefan Roese
fb384c4720 mtd: nand: omap_gpmc: Always use ready/busy pin
The functions to detect the state of the ready / busy signal is already
available but only used in the SPL case. Lets use it always, also for the
main U-Boot. As all boards should have this HW connection.

Testing on Siemens Draco (am335x) showed a small perfomance gain by using
this ready pin to detect the NAND chip state. Here the values tested on
Draco with Hynix 4GBit NAND:

Without NAND ready pin:

U-Boot# time nand read 80400000 0 400000

NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK

time: 2.947 seconds, 2947 ticks

With NAND ready pin:

U-Boot# time nand read 80400000 0 400000

NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK

time: 2.795 seconds, 2795 ticks

So an increase of approx. 5%.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
2014-12-04 21:28:31 -05:00
Stefan Roese
e49631afa0 arm: am33xx: Handle NAND+I2C boot-device the same way as NAND
Re-map NAND&I2C boot-device to the "normal" NAND boot-device.
Otherwise the SPL boot IF can't handle this device correctly.
Somehow booting with Hynix 4GBit NAND H27U4G8 on Siemens
Draco leads to this boot-device passed to SPL from the BootROM.

With this change, Draco boots just fine into main U-Boot.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
2014-12-04 21:28:31 -05:00
Lubomir Popov
ae525189f0 ARM: OMAP5: DRA7xx: Fix misleading comments in mux_data.h
The comments on the QSPI pad assignments erronously swapped
the qspi1_d0 and qspi1_d1 functionality and could cause
confusion. QSPI1_D[0] is in fact muxed on pad U1 (gpmc_a16),
and QSPI1_D[1] - on pad P3 (gpmc_a17). Fixing comments.

Signed-off-by: Lubomir Popov <l-popov@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-12-04 21:28:31 -05:00
Lubomir Popov
8065a4e83d ARM: OMAP5: DRA7xx: Enable 8-bit eMMC access on the dra7xx_evm
Tested on a Vayu EVM Rev.E2 with DRA752 ES1.1

Signed-off-by: Lubomir Popov <l-popov@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-12-04 21:28:31 -05:00