Move tapdelay function calls to zynq_sdhci.c and make them static
inline. zynqmp_tap_delay.h has function prototypes for the functions
defined in tap_delays.c, which will not be needed anymore.
Remove tap_delays.c and zynqmp_tap_delay.h files.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Currently xilinx sdhci driver is using zynqmp_mmio_write() to set
tapdelay values and DLL resets. Continue to use this for SPL and mini
U-Boot where U-Boot will be executed at EL3 level.
Use firmware call xilinx_pm_request() using appropriate arguments to
set input/output tapdelays and also for DLL resets in regular flow(EL2).
Host driver should explicitly request DLL reset before ITAP (assert DLL)
and after OTAP (release DLL) to avoid issues in some cases. Also handle
error return where possible.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The main reason for this to be implemented is capsule update.
Two memories are supported and tested which is MMC FAT based and QSPI
based.
For creating capsule these commands are used:
./tools/mkeficapsule --raw spl/boot.bin --index 1 capsule1.bin
./tools/mkeficapsule --raw u-boot.itb --index 2 capsule2.bin
Then transfer to SD card where these commands run:
load mmc 0 10000000 capsule1.bin
efidebug capsule update -v 10000000
load mmc 0 10000000 capsule2.bin
efidebug capsule update -v 10000000
Depends on the boot device used are binaries loaded to qspi or mmc fat
partition.
Also multiboot register is handled to make sure that the same location(id)
is used as image which is upgraded.
Two locations are used by purpose for SPL flow. If only boot.bin is used
create only one capsule.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When U-Boot runs in EL2 there is no access to csu_base registers that's why
this has to be done via firmware interface to find out multi boot register
value. Till now this function is called only from SPL in EL3.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change multi_boot() to return multiboot value and move print out of this
function and let this function to be used by other functions without
duplicating message.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When env_set() is called there is no need to allocate memory for variable
which is already saved that's why free it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The SPL can also be compiled with sysreset drivers just fine, so
update the condition to cater for that option.
The same change was done by commit efa1a62ad2 ("ARM: imx8m: Do not define
do_reset() if sysreset is enabled").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The system refuses to boot without any environment, so return ENVL_NOWHERE when
there's nowhere to store the environment instead of ENVL_UNKNOWN.
This fixes that the board won't boot from eMMC when CONFIG_ENV_IS_IN_FAT is not
defined, for example. Similar for other combinations.
Fixes: 1025bd098a "xilinx: zynqmp: Add support for saving variables"
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Split arasan_zynqmp_set_tapdelay() to handle input and output tapdelays
separately. This is required to handle zero values for ITAP and OTAP
values. If we dont split, we will have to remove the if() in the
function, which makes ITAP values to be overwritten when OTAP values are
called to set and vice-versa.
Restrict tap_delay value calculated to max allowed 8 bits for ITAP and 6
bits for OTAP for ZynqMP.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add zynqmp 67dr silicon to zynqmp device id table.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
TF-A and SecureOS can allocate the part of DDR for self but U-Boot is not
handling this configuration that the part of memory is reserved and
shouldn't be used by U-Boot. That's why read all reserved memory locations
and don't use it.
The code was taken from commit 4a1b975dac ("board: stm32mp1: reserve
memory for OP-TEE in device tree") and commit 1419e5b516 ("stm32mp:
update MMU config before the relocation") which is used by stm32 and does
the job properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
K26 has EMMC and SD and default 0 is not working when system is booting out
of SD which is controller 1. Add controller autodetection via
mmc_get_env_dev(). The same code is used for distro_boot selection done in
board_late_init(). bootseq variable can't be reused because this is called
so late.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SVDs are using different name which can't be handled via zynqmp_devices
structure. That's why introduce zynqmp_detect_svd_name() which checks ID
code for these devices and show proper name for them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].
[1] https://github.com/Xilinx/embeddedsw
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In usb boot mode distro boot should select usb device as primary boot
device instead of usb host. So make usb dfu as primary boot device. But do
not list it in boot_targets as fallback option because it is not classic
mode for booting. Using 60s timeout by default should be enough time for
dfu-utils to start transaction. In case none needs this please change
timeout value in the command or disable CONFIG_DFU_TIMEOUT.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYDUezQAKCRDKSWXLKUoM
IbtgAJ9jZ+BOtwFaHR19TENC2DsHTINnnwCfSDn3fU0OFJRI0HD7pRxXr4xrb3M=
=Kr8x
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.04-rc3
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
Folder names corresponds to DT name. These boards have been renamed from
zc1275 to zcu1275 by commit shown below and this should be the part of that
commit.
Fixes: 420d446781 ("arm64: zynqmp: Rename zc1275 to zcu1275")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no need to clear reset reason register because it is protected by
PMUFW already which is reported when verbose log is enabled as:
pm_core.c@733 APU> No write permission to 0xFF5E0220
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Both Zynq and ZynqMP can show silicon versions in SPL boot flow. It is
useful to be aware.
The patch is also fixing possition of these bits on ZynqMP.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
For systems which has both sdhci controllers enable it is worth to export
bootseq number for variables. Then the variable can be used in custom
scripts to tune logic for OS.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
-----BEGIN PGP SIGNATURE-----
iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
=4FnY
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.04
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
All Xilinx SoCs have repository location filled already but boards are
covered by different fragment which is missing this link.
The patch is extending description with adding proper link to the same
repository.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove setting tapdelays for different speeds separately. Instead use
the ITAP and OTAP delay values which are read from the device tree.
If the DT does not contain tap delay values, the predefined values
will be used for the same.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Define timing macro's for all the available speeds of mmc. This is
done similar to linux. Replace speed macro's used with these new timing
macro's wherever applicable.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
U-Boot SPL on ZynqMP is using CONFIG_SPL_USE_TINY_PRINTF which doesn't
return any return value and all the time returns 0. That's why
even correct snprintf was returning in SPL chip ID as "unknown".
Change checking condition and allow snprintf to return 0 which is according
manual patch successful return.
"If an output error is encountered, a negative value is returned."
Fixes: 43a138956f7e ("arm64: zynqmp: Get rid of simple_itoa and replace it by snprintf")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix hex format from 0x%0X to 0x%0x to show correct numbers.
Fixes: fa793165da ("xilinx: zynqmp: refactor silicon name function")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for fru commands "fru capture" and "fru display".
The fru capture parses the FRU table present at an address and stores in a
structure for later use. The fru display prints the content of captured
structured in a readable format.
As of now, it supports only common header and board area of FRU. Also, it
supports only English language code and ASCII8/BINARY formats.
fru_data variable is placed to data section because fru parser can be
called very early before bss is initialized. And also information needs to
be shared that's why it is exported via header.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no need to reference files in common folder back. Simply adding
Makefile to this folder does the job because this "common" location is
already wired in main Makefile.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Starts to use new way how eeproms should be referenced.
Reference is done via nvmem alias nodes. When this new way is specified
code itself read the eeprom and decode xilinx legacy format and fill struct
xilinx_board_description. Then based on information present there board_*
variables are setup.
If variables are saved and content can't be changed information is just
shown on console.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
By default 48B sha3 hash value is written to srcaddr which is not the best
solution in case of that you want to use data for other operations. That's
why add key_addr optional parameters which enables to write 48B sha3 hash
value to specified address.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
This patch adds support for SHA3 command. It takes data blob
as input and generates 48 bytes sha3 hash value.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for RSA command, performs RSA encrypt &
RSA decrypt on data blob of key size.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for encryption and decryption on a given data
blob using different key sources such as userkey(KUP), device key and
PUF key. Inorder to support this a new zynqmp command(zynqmp aes) has
been introduced.
Command:
zynqmp aes srcaddr ivaddr len aesop keysrc dstaddr [keyaddr]\n"
Encrypts or decrypts blob of data at src address and puts it\n"
back to dstaddr using key and iv at keyaddr and ivaddr\n"
respectively. keysrc values specifies from which source key\n"
has to be used, it can be User/Device/PUF key. A value of 0\n"
for KUP(user key),1 for DeviceKey and 2 for PUF key. The\n"
aesop value would specify the operationwhich can be 0 for\n"
decrypt and 1 for encrypt(1) operation\n";
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
simple_itoa() is implemented only for !CONFIG_USE_TINY_PRINTF. Tiny printf
is normally used by SPL that's code which uses simple_itoa() has missing
reference. That's why refactor code by using on snprintf() instead of
strncpy()/strncat() combination. This change also descrease code size by
saving 24B based on buildman.
aarch64: (for 1/1 boards) all -22.0 rodata +2.0 text -24.0
xilinx_zynqmp_virt: all -22 rodata +2 text -24
u-boot: add: 0/0, grow: 0/-1 bytes: 0/-24 (-24)
function old new delta
board_init 520 496 -24
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
9cg version was supported before code refactoring. The patch is adding it
back.
Fixes: fa793165da ("xilinx: zynqmp: refactor silicon name function")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enabling saving variables to MMC(FAT), NAND, SPI based on primary bootmode.
Maybe that logic can be tuned for more complicated use cases and better
tested for different bootmodes.
Tested on zcu104 to SD(FAT) and JTAG(NOWHERE).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to have name variable saved in BSS section when it
doesn't need to be really used. That's why remove static from variable
definition and use strdup() to duplicate string with exact size from malloc
area instead.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current algorithm used to get the silicon name is bit complicated and
hard to follow. Updated to use more straightforward mechanism based on
the Device ID code table (Table 1-2). The full IDCODE register is used
(except device revision bits [31:28]) to get the device name and IDCODE2
value is used for identifying the variant.
Additionally to make the algorithm bit more clear it also save some space
as the devices table is slightly bit smaller.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Since commit 86cf1c8285 ("configs: Migrate CONFIG_NR_DRAM_BANKS") &
commit 999a772d9f ("Kconfig: Migrate CONFIG_NR_DRAM_BANKS"),
CONFIG_NR_DRAM_BANKS is always defined with a value (4 is default).
It makes no sense to still carry code that is guarded with
"#ifndef CONFIG_NR_DRAM_BANKS" (and similar). This patch removes
all these unreferenced code paths.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Start to use ENV_VARS_UBOOT_RUNTIME_CONFIG to enable/disable updating
variables with run time information.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove chip_id function and integrate the firmware call in the
zynqmp_get_silicon_idcode_name function. The change avoids querying the
firmware twice and makes the code bit more clear.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify the board init function to allow getting the chip ID when U-Boot
proper is executed at EL3.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current implementation for getting chip ID uses either raw access on EL3
or a SMC call to get the silicon information. Following change
simplifies the code using always the firmware driver.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Origin function was calling strsep which replaced delimiter ',' by a null
byte ('\0'). Operation was done directly on FDT which ends up with the
following behavior:
ZynqMP> printenv fdtfile
fdtfile=xilinx/zynqmp.dtb
ZynqMP> fdt addr $fdtcontroladdr
ZynqMP> fdt print / compatible
compatible = "xlnx", "zynqmp"
As is visible fdtfile was correctly composed but a null byte caused that
xlnx was separated from zynqmp.
This hasn't been spotted because in all Xilinx DTs there are at least 3
compatible string and only the first one was affected by this issue.
But for systems which only had one compatible string "xlnx,zynqmp" it was
causing an issue when U-Boot's DT was used by Linux kernel.
The patch removes strsep calling and strchr is called instead which just
locate the first char after deliminator ',' (variable called "name").
And using this pointer in fdtfile composing.
Fixes: 91d7e0c47f ("arm64: zynqmp: Create fdtfile from compatible string")
Reported-by: Igor Lantsman <igor.lantsman@opsys-tech.com>
Signed-off-by: Igor Lantsman <igor.lantsman@opsys-tech.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
PMU FW has functionality to accept and reload configuration object at run
time. The patch is adding support for doing it via u-boot prompt.
For example:
tftpboot 100000 pmu_obj.bin
zynqmp pmufw 100000 $filesize
The most of pmufw configurations don't allow config reloading.
Also official Xilinx PMUFW doens't support this feature properly but the
patch should open a way to call PMUFW with this request.
Here is example of PMUFW config fragment which enables config reloading.
/* SET CONFIG SECTION */
PM_CONFIG_SET_CONFIG_SECTION_ID, /* Section ID */
PM_CONFIG_IPI_PSU_CORTEXA53_0_MASK | PM_CONFIG_IPI_PSU_CORTEXR5_0_MASK |
PM_CONFIG_IPI_PSU_CORTEXR5_1_MASK, /* Permissions to set config */
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is better to print multiboot value in decimal because boot images are
also composed in decimal not in hex.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
XDP - Xilinx Drone Platform is a board for drones or other UAV.
Pinmux the SD card by default, and if the SD card detect line is high
(inactive) then pinmux the SD1 interface to EMIO instead. SD is placed on
extension card and shares connection with on board wife. That means that
when SD card is present in the board wifi can't be used.
There seems to be an issue with DDR access from PL at 2400MT/s, after
updating the PMU and ATF firmware this is causing extremely slow DDR
access. Reducing the DDR speed from 2400 to 2133 appears to solve that
issue, even though the hardware has proven to be 2400 capable.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A bug in the ZynqMP bootrom sets the PS_SYSMON_ANALOG_BUS register
at 0xFFA50914 to the wrong value 0x3201. This causes the AMS to
exchange the PS supply voltages 0 and 1. On Xilinx boards this is
not noticeable since these are tied together, it's only really
noticeable if banks 500 and 501 have different supplies. Xilinx' tech
support reported this undocumented register to be the cause, and
this patch applies a fix for all boards by programming the correct
value.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create special function for reading bootmode on Versal and ZynqMP.
Zynq is using specific function (without mask) already.
Future patches will be calling this function from different location too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Parameter order is not correct based on zynqmp_mmio_write() declaration.
Fixes: be52372ff1 ("arm64: zynqmp: Use zynqmp_mmio_read/write functions")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Delay required for clock propagation is tighly coupled with initialization
done in psu_init(). That's why call it also for u-boot proper with
CONFIG_ZYNQMP_PSU_INIT_ENABLED enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_early_init_f() is the right location where debug uart can be
configurated (after MIO initialization).
The patch is taking this call from SPL to also make it available for U-Boot
proper.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP mini configurations works without PMU firmware that's why there is
no reason to enable the driver and check if it was probed properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Multi boot register can be used for using different boot images and design
better boot strategy. Let EL3 SPL or U-Boot to read it and print it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DEVICE_TREE variable is not exported from dts/Makefile that's why it is
necessary to setup directly before use.
Fixes: 312f2c5b14 ("arm: xilinx: Use device tree which can be passed on cmd line")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DEVICE_TREE variable has been added by commit 6ab6b2afa0
("dts: re-write dts/Makefile more simply with Kbuild")
where DT can be specified on command line. If it is not then
CONFIG_DEFAULT_DEVICE_TREE is used to ensure backward compatibility.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Names have to match device tree file names. Also add missing one.
Fixes: 50d9283347 ("arm64: zynqmp: Sync names for SC with Versal")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to do serial initialization. Uart driver does it already
based on DT. Good effect is that it is clear which interface is console.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
MIO34 is connected to POWER_KILL signal. When MIO configuration is done in
psu_init() and this pin is assigned to PMU but PMU configuration is not
loaded yet. PMU gpio output is high that means board is powered off
immediately.
The patch is fixing this sequence that MIO34 stays assing to ps gpio IP.
PMU config is loaded in SPL and then pin assigned to PMU through
psu_post_config_data().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently "script_offset_f" env variable is hardcoded, this variable
specifies from which offset of the flash boot.scr should be read/write.
As flashes are of different sizes having a fixed offset makes it
difficult to load other images into the flash which may overwrite the
boot script or cannot utilize the full memory. This current fix
creates a new config "CONFIG_BOOT_SCRIPT_OFFSET" which holds the
offset address, overwrites the "script_offset_f" variable.
Also removed existing variable with default values, as the default
values are held by CONFIG_BOOT_SCRIPT_OFFSET
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Emmc boot devcie is mounted to mmc@ff160000 controller on zynqmp.
Detect mmc alias at run time for setting up proper boot_targets
sequence instead of setting boot_targets manually.
Removed setting "modeboot" variable as it not longer need as we
switched to distro boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove macros which use PM_SIP_SVC offset and convert invoke_smc() to
xilinx_pm_request() which do calculation with PM_SIP_SVC already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Probe ZynqMP firmware driver on the board initialization phase and
ensure that firmware is in place to continue execution. The probing is
done on board_init so it can be used for both SPL and U-Boot proper.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use the new function from firmware version to get the firmware version.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
New firmware header to place firmware specific macro and function
declarations. The patch also moves the macros defining PM operations as
well as some helper macros.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Similar SCs but different wiring.
- dc_i2c is connected to X-PRC cards that's why label is required to have
an option to hook up some devices.
- Exactly identify i2c devices on x-prc boards.
In case of missing i2c connection devices won't be accessible.
- USB 0 should be device mode with super speed.
- USB 1 should be host mode.
- Fix i2c mux reset pin entry - commented, not verified.
- Fix i2c1 eeprom compatible string - it is an ST 128Kbit device.
Need to use atmel fallback.
- Fix si570 I2C slave address and add corresponding part numbers.
- Enable AMS for system monitoring.
- phy reset property should be commented because it will throw a
warning dump when called from context that can sleep.
No support for phys property (zynqmp phy driver) with SGMII.
Add is-internal-pcspma property required by uboot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Add zu48dr and zu49dr to the list of zynqmp devices. The zu48dr and zu49dr
are the new RFSoC silicons with id values of 0x7b and 0x7e.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new jtag distro boot command to look for bootscript file in
DDR and execute it first incase of jtag bootmode.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>