This patch adds NAND booting support for the AMCC Acadia eval board.
Please make sure to configure jumper J7 to position 2-3 when booting
from NOR, and to position 1-2 when booting for NAND.
I also added a board command to configure the I2C bootstrap EEPROM
values. Right now only 267MHz is support for booting either via NOR
or NAND FLASH. Here the usage:
=> bootstrap 267 nor ;to configure the board for 267MHz NOR booting
=> bootstrap 267 nand ;to configure the board for 267MHz NNAND booting
Signed-off-by: Stefan Roese <sr@denx.de>
e600 does not have a bootpg restriction.
Move the version string to beginning of image at fff00000.
Resetvec.S is not needed.
Update flash copy instructions.
Add tftpflash env variable
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The attached patch is mainly cosmetic, allowing u-boot to
display the correct bootstrap option letter according to the
datasheets.
The original patch was extended with 405EZ support by Stefan
Roese.
Signed-off-by: Benoit Monin <bmonin@adeneo.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch undoes the patch by Jeff Mann with commit-id ada4697d. As
suggested by AMCC it is not recommended to dynamically change the EBC
speed after bootup. So we undo this change to be on the safe side.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds NAND booting support for the AMCC Bamboo eval board.
Since the NAND-SPL boot image is limited to 4kbytes, this version
only supports the onboard 64MBytes of DDR. The DIMM modules can't be
supported, since the setup code for I2C DIMM autodetection and
configuration is too big for this NAND bootloader.
Signed-off-by: Stefan Roese <sr@denx.de>
The U-Boot NAND booting support is now extended to support ECC
upon loading of the NAND U-Boot image.
Tested on AMCC Sequoia (440EPx) and Bamboo (440EP).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch updates the "normal" Bamboo NOR booting port, so
that it is compatible with the coming soon NAND booting
Bamboo port.
It also enables the 2nd NAND flash on the Bamboo.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds hardware ECC support to the NDFC driver. It also
changes the register access from using the "simple" in32/out32
functions to the in_be32/out_be32 functions, which make sure
that the access is correctly synced. This is the only recommended
access to SoC registers in the current Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch updates the nand_ecc code to the latest Linux version.
The main reason for this is the more compact code. This makes
it possible to include the ECC code into the NAND bootloader
image (NAND_SPL) for PPC4xx.
Signed-off-by: Stefan Roese <sr@denx.de>
Enable redundant environment, add a MTD partition for it; also add env.
variable command for passing MTD partitions to the kernel command line.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
Allow passing longer command line to the kernel - useful especially
for passing MTD partition layout.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
Change EEPROM configuration according to the datasheet: "The 24C01A and 24C02A
have a page write capability of two bytes", and "This device offers fast (1ms)
byte write". Add 3ms of extra delay.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
After being reset in mpc5xxx_fec_init_phy(), PHY goes into FX mode, in which
networking does not function. This commit switches PHY to TX mode by clearing
the FX_SEL bit of Mode Control Register. It also reverses commit
008861a2f3, i.e., a temporary workaround.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
Both CFG_PCISPEED_66 and CFG_IPBSPEED_133 are misnamed, as defining
them does not cause PCI or IPB clocks to run at the specified speed.
Instead, they configure divisors used to calculate said clocks. This
patch renames the defines according to their real function.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
As pointed out by Bruce Adler <bruce.adler@acm.org> this patch
fixes a small bug in the 405EZ OCM initialization. Thanks for
spotting.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch updates the Acadia (405EZ) support for the new 1.1 board
revision. It also adds support for NAND FLASH via the 4xx NDFC.
Please note that the jumper J7 must be in position 2-3 for this
NAND support. Position 1-2 is for NAND booting only. NAND booting
support will follow later.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for 405 PPC's to the 4xx NAND driver
ndfc.c. This is in preparation for the new AMCC 405EZ.
Signed-off-by: Stefan Roese <sr@denx.de>
