Move axi timer driver from Microblaze to generic location.
Origin implementation was irq based with counting down timer.
CONFIG_TIMER drivers are designed differently that timer is free running up
timer with automatic reload without any interrupt.
Information about clock rates are find out in timer_pre_probe() that's why
there is no need to get any additional information from DT in the driver
itself (only register offset).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Tested-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/6c12fc86bbc1f17d05c25018862e7b7b03346b36.1654684731.git.michal.simek@amd.com
Add a basic CPU driver that retrieves information about the microblaze CPU
core. cpu_ops handlers are implemented so that the "cpu" command can work
properly:
U-Boot-mONStR> cpu list
0: cpu@0 MicroBlaze @ 50MHz, Rev: 11.0, FPGA family: zynq7000
U-Boot-mONStR> cpu detail
0: cpu@0 MicroBlaze @ 50MHz, Rev: 11.0, FPGA family: zynq7000
ID = 0, freq = 50 MHz: L1 cache, MMU
Note: cpu_ver_lookup[] and family_string_lookup[] arrays were imported from
linux.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-14-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Align microblaze with the other architectures and provide an
implementation for flush_dcache_range(). Also, remove the microblaze
exception in drivers/core/device.c.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-11-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Relocate cpu_ops pointers when CONFIG_NEEDS_MANUAL_RELOC is enabled.
The (gd->flags & GD_FLG_RELOC) check was added to make sure the reloc_done
logic works for drivers that use DM_FLAG_PRE_RELOC.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support to handle 'output-enable' and 'bias-high-impedance'
configurations. DT property output-enable brings out the pins from
tri-state, whereas bias-high-impedance changes the pins state to
tri-state.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/1a02cd41d183d397ebce23c497178281c7286692.1655286745.git.michal.simek@amd.com
CONFIG_DM_ETH_PHY enables support to utilize generic ethernet phy
framework. Though if ethernet PHY node is in other ethernet node, it
will use shared MDIO to access the PHY of other ethernet. Move ethernet
print info statement from plat function to probe function, as phyaddr is
not enumerated when CONFIG_DM_ETH_PHY is enabled.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/93e11ccca56b6e52b2dcc283d08d5042537f828f.1652181968.git.michal.simek@amd.com
CONFIG_DM_ETH_PHY enables support to utilize generic ethernet phy
framework. Though if ethernet PHY node is in other ethernet node, it
will use shared MDIO to access the PHY of other ethernet. Move ethernet
print info statement from plat function to probe function, as phyaddr is
not enumerated when CONFIG_DM_ETH_PHY is enabled.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/ecfec78234233fefdc172c141c207b2d78ef70c5.1652181968.git.michal.simek@amd.com
This consists of two slightly related series. For the first, to quote
the author:
This series implements 2 features in driver/firmware/scmi.
First, a single change adds support for SCMI OP-TEE transport to
use OP-TEE native shared memory. See the 1st patch in this series:
"firmware: scmi: optee: use TEE shared memory for SCMI messages".
Then come changes for supporting multi-channel in the SCMI drivers.
I've split the implementation in 11 several small incremental changes
in the hope it helps the review. Few minor fixup commits are also
inserted in the series.
And the second series implements some smccc improvements.
Adds random number generator driver using Arm SMCCC TRNG interface to
get entropy bytes from secure monitor. The driver registers as an
Arm SMCCC feature driver to allow PSCI driver to bind a device for
when secure monitor exposes RNG support from Arm SMCCC TRNG interface.
Cc: Sughosh Ganu <sughosh.ganu@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Use PSCI device to query Arm SMCCC v1.1 support from secure monitor
and if so, bind drivers for the SMCCC features that monitor supports.
Drivers willing to be bound from Arm SMCCC features discovery can use
macro ARM_SMCCC_FEATURE_DRIVER() to register to smccc feature discovery,
providing target driver name and a callback function that returns
whether or not the SMCCC feature is supported by the system.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Updates .process_msg operators of the SCMI transport drivers that
supports multi-channel to use it now that drivers do provide
the reference through channel argument. These are the mailbox
agent, the optee agent and the smccc agent.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Update SCMI regulator controller driver to get its assigned SCMI channel
during initialization. This change allows SCMI voltage domain protocol
to use a dedicated channel when defined in the DT. The reference is
saved in SCMI regulator controller driver private data.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Update SCMI reset controller driver to get its assigned SCMI channel
during initialization. This change allows SCMI reset domain protocol
to use a dedicated channel when defined in the DT. The reference is
saved in SCMI reset controller driver private data.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Update SCMI clock driver to get its assigned SCMI channel during
initialization. This change allows SCMI clock protocol to use a
dedicated channel when defined in the DT. The reference is saved
in SCMI clock driver private data.
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Implements multi SCMI channel support in OP-TEE SCMI transport. An
SCMI protocol may use a dedicated channel, specified by the DT.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Updates SCMI SMCCC transport driver to get SCMI channel reference
at initialization and use when posting SCMI messages.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Updates SCMI mailbox transport driver to get SCMI channel reference
at initialization and use when posting SCMI messages.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Adds resources for SCMI protocols to possibly use a dedicated SCMI
channel instead of the default channel allocated by the SCMI agent
during initialization. As per DT binding documentation, some SCMI
transports can define a specific SCMI communication channel for
given SCMI protocols. It allows SCMI protocols to pass messages
concurrently each other.
This change introduces new scmi agent uclass API function
devm_scmi_of_get_channel() for SCMI drivers probe sequences to get
a reference to the SCMI channel assigned to its related SCMI protocol.
The function queries the channel reference to its SCMI transport driver
through new scmi agent uclass operator .of_get_channel that uses Device
Tree information from related SCMI agent node.
Operator .of_get_channel returns a reference to the SCMI channel
assigned to SCMI protocol used by the caller device. SCMI transport
drivers that do not support multi-channel are not mandated to register
this operator. When so, API function devm_scmi_of_get_channel() returns
NULL and SCMI transport driver are expected to retrieve by their own
means the reference to the unique SCMI channel, for example using
platform data as these drivers currently do in U-Boot source tree.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Defines local helper function find_scmi_transport_device() with the
instructions to find the SCMI transport device from a SCMI protocol
device.
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Changes SCMI driver API function devm_scmi_process_msg() to add
an SCMI channel reference argument for when SCMI agent supports
SCMI protocol specific channels. First argument of devm_scmi_process_msg()
is also change to point to the caller SCMI protocol device rather
than its parent device (the SCMI agent device).
The argument is a pointer to opaque struct scmi_channel known from
the SCMI transport drivers. It is currently unused and caller a pass
NULL value. A later change will enable such support once SCMI protocol
drivers have means to get the channel reference during initialization.
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Changes implementation when using TEE dynamically allocated shared
memory to synchronize with the Linux implementation where the legacy
SMT protocol cannot be used with such memory since it is expected from
device mapped memory whereas OP-TEE shared memory is cached and
hence should not be accessed using memcpy_toio()/memcpy_fromio().
This change implements the MSG shared memory protocol introduced
in Linux [1]. The protocol uses a simplified SMT header of 32bit
named MSG_SMT to carry SCMI protocol information and uses side channel
means to carry exchanged buffer size information, as TEE invocation API
parameters when used in the SCMI OP-TEE transport.
Link: [1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=f301bba0ca7392d16a6ea4f1d264a91f1fadea1a
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Add a fuzzing engine driver for the sandbox to take inputs from
libfuzzer and expose them to the fuzz tests.
Signed-off-by: Andrew Scull <ascull@google.com>
This new class of device will provide fuzzing inputs from a fuzzing
engine.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix the buffer underflow that would occur if puts is called with length
of zero.
Fixes: efa51f2bd6 ("serial: sandbox: Implement puts")
Cc: Sean Anderson <sean.anderson@seco.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
The GXP supports 3 separate SPI interfaces to accommodate the system
flash, core flash, and other functions. The SPI engine supports variable
clock frequency, selectable 3-byte or 4-byte addressing and a
configurable x1, x2, and x4 command/address/data modes. The memory
buffer for reading and writing ranges between 256 bytes and 8KB. This
driver supports access to the core flash.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Add support for the HPE GXP SOC timer. The GXP supports several different
kinds of timers but for the purpose of this driver there is only support
for the General Timer. The timer has a 1us resolution and is 56 bits.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmKsehgACgkQ4rK92eCq
k3UexAf+JThCd7FlN3OkTVKIdZKeNm2KpQxrqt20whiqp/nSUzxXrjdlCTKZEER2
lLJoVnwr+bkmdlqsa6gAZXSsd0lUv37XnLsLA5or278tFNlKp6gzYrz49FR59mVC
ie7/NlY5FgM5qmKGCob7tjwJ78r2/S3T2EaLiAMWUmw2UB5KZU6h3napHZ+1T0se
vaEAVRzAaZeYzKU3k6RBSv2tXQ6ssvfpp9RcXpRGtrN908AqDhHiOfntuOrnsEe0
9rjY1DSXO9a5WqHRm2KQ3FrA/By2layQ+4WH/HgIPHasisnmo3E/euVWmhtTaiT/
g5bOLwyFQ2/RvdMlMxXlKUcuMfNwRA==
=Hhzj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220620' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Add STM32MP13 SoCs support with associated board STM32M135F-DK
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
Currently default fallback SDHC mode is 1-bit. Add new config option
CONFIG_SYS_FSL_ESDHC_DEFAULT_BUS_WIDTH to allow specifying default fallback
mode. This is useful e.g. for SPL builds which loads other parts from SD
card during boot process.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
8-bit mode is not supported by SD cards and on P2020 are four SDHC pins
shared with SPI (so if P2020 board have also SPI then only 4-bit SDHC mode
is provided). So 8-bit SDHC mode is really bad default.
When max bus width is not provided then set mode to 1-bit. This mode is
supported by all cards, so it is the best option for fallback mode.
Also P2020 bootrom sets mode to 1-bit when booting from SD/MMC card.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
For proper DM support it is required to fill also mtd->dev member.
Otherwise DM would not see nand device at all.
Signed-off-by: Pali Rohár <pali@kernel.org>
This adds a driver for the Security Fuse Processor (SFP) present on
LS1012A, LS1021A, LS1043A, and LS1046A processors. It holds the
Super-Root Key (SRK), One-Time-Programmable Master Key (OTPMK), and
other "security" related fuses. Similar devices (sharing the same name)
are present on other processors, but for the moment this just supports
the LS2 variants.
The mirror registers are loaded during power-on reset. All mirror
registers must be programmed or read at once. Because of this, `fuse
prog` will program all fuses, even though only one might be specified.
To prevent accidentally burning through all your fuse programming cycles
with something like `fuse prog 0 0 A B C D`, we limit ourselves to one
programming cycle per reset. Fuses are numbered based on their address.
The fuse at 0x1e80200 is 0, the fuse at 0x1e80204 is 1, etc.
The TA_PROG_SFP supply must be enabled when programming fuses, but must
be disabled when reading them. Typically this supply is enabled by
inserting a jumper or by setting a register in the board's FPGA. I've
also added support for using a regulator. This could be helpful for
automatically issuing the FPGA write, or for toggling a GPIO controlling
the supply.
I suggest using the following procedure for programming:
1. Override the fuses you wish to program
=> fuse override 0 2 A B C D
2. Inspect the values and ensure that they are what you expect
=> fuse sense 0 2 4
3. Enable TA_PROG_SFP
4. Issue a program command using OSPR0 as a dummy. Since it contains the
write-protect bit you will usually want to write it last anyway.
=> fuse prog 0 0 0
5. Disable TA_PROG_SFP
6. Read back the fuses and ensure they are correct
=> fuse read 0 2 4
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Replace reference to the correct name STMicroelectronics
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the MISC RCC driver for STM32MP13, and bind it to the RCC reset
driver, required for initial support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Change-Id: Ida11c15462caf140f87b1e3239efa2b8a689acb9
Add a directory in drivers/clk to regroup the clock drivers for all
STM32 Soc with CONFIG_ARCH_STM32 (MCUs with cortex M) or
CONFIG_ARCH_STM32MP (MPUs with cortex A).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Acked-by: Sean Anderson <seanga2@gmail.com>
Change-Id: I955af307963f732167396f0157a30cf2fc91f150
Although not recommended, the reset property could be made optional.
This way the driver will probe even if no reset property is provided
in an sdmmc node in DT. This reset is already optional in Linux.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add support for new compatible "st,stm32mp13-ddr" to manage the
DDR sub system (Controller and PHY) in STM32MP13x SOC:
- only one AXI port
- support of 16 port output (MEMC_DRAM_DATA_WIDTH = 2)
The STM32MP15x SOC have 2 AXI ports and 32 bits support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Convert the constant integer to 'phys_size_t' to avoid overflow
when calculating the SDRAM size.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
There is hardware bug in NCORE CCU IP and it is causing an issue in the
coherent directory tracking of outstanding cache lines.
The workaround is disabling snoop filter.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add support for "st,stm32mp135-pinctrl" for STM32MP13x
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The generic EHCI binding does not *require* resets and clocks
properties, and indeed for instance the Allwinner A20 SoCs does not
need or define any resets in its DT.
Don't easily give up if clk_get_bulk() or reset_get_bulk() return an
error, but check if that is due to the DT simply having no entries for
either of them.
This fixes USB operation on all boards with an Allwinner A10 or A20 SoC,
which were reporting an error after commit ba96176ab7:
=======================
Bus usb@1c14000: ehci_generic usb@1c14000: Failed to get resets (err=-2)
probe failed, error -2
=======================
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
While working on an LX2160 based board and updating to latest mainline
I noticed problems using the HW accelerated hash functions on this
platform, when trying to boot a FIT Kernel image. Here the resulting
error message:
Using 'conf-freescale_lx2160a.dtb' configuration
Trying 'kernel-1' kernel subimage
Verifying Hash Integrity ... sha256Error: Address arguments are not aligned
CAAM was not setup properly or it is faulty
error!
Bad hash value for 'hash-1' hash node in 'kernel-1' image node
Bad Data Hash
ERROR: can't get kernel image!
Testing and checking with Gaurav Jain from NXP has revealed, that this
alignment check is not necessary here at all. So let's remove this
check completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Gaurav Jain <gaurav.jain@nxp.com>
Cc: dullfire@yahoo.com
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Replace with phys_size_t for all memory size variables declaration
for the sake of scalability. phys_size_t is defined in
/arch/arm/include/asm/types.h.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Bit[7-4] for both register seq2core and core2seq handshake in HPS are not
required for triggering DDR re-calibration or resetting EMIF. So, ignoring
these bits just for playing it safe.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
All the source code of sdram_n5x.c are from Intel, update the license to
use both GPL2.0 and BSD-3 Clause because this copy of code may used for
open source and internal project.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
The nxp_fspi_default_setup() is only ever called from nxp_fspi_probe(),
where the IP clock are initially disabled. Drop the second disabling of
clock to prevent clock enable/disable imbalance reported by clock core:
"
clk qspi_root_clk already disabled
"
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There is no wait_dat0 mmc ops, causing operations waiting for data
line state change (e.g mmc_switch_voltage) to fallback to a 250ms
active delay. mmc_ops still used when DM_MMC is not enabled, which
is often the case for SPL. The result can be unexpectly long SPL
boot time.
This change adds support for wait_dat0() mmc operation.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix the end address in the message for unaligned erase request in
mmc_berase() when start + blkcnt is aligned to erase_grp_size.
for example:
- start = 0x2000 - 26
- count = 26
- erase_grp_size = 0x400
Caution! Your devices Erase group is 0x400
The erase range would be change to 0x2000~0x27ff
But no issue when the end address is not aligned, for example
- start = 0x2000 - 2 * 26
- count = 26
- erase_grp_size = 0x400
Caution! Your devices Erase group is 0x400
The erase range would be change to 0x2000~0x23ff
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Upstream commit 7a2c3be95a ("clk: imx8mp: Fill in DWC3 USB, USB PHY,
HSIOMIX clock") added usb_core_ref for USB Controller but never set it
to be used as a clock source, using rather "osc_32k" instead.
This produces following boot log message:
"clk_register: failed to get osc_32k device (parent of usb_root_clk)"
Fix the USB controller clock source by using usb_core_ref instead of
osc_32k.
Fixes: 7a2c3be95a ("clk: imx8mp: Fill in DWC3 USB, USB PHY, HSIOMIX clock")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Root clock name contained underscore, which does not match to the actual
clock name.
Correct the name to match what is present in the FDT.
Fixes: 87f958810f ("clk: imx8mp: Add ECSPI clocks")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The ADIN1300 supports generating certain clocks on its GP_CLK pin, as
well as providing the reference clock on CLK25_REF.
Add support for selecting the clock via device-tree properties.
This patch is based on the Linux implementation for this feature,
which has been added to netdev/net-next.git [1].
[2] https://patchwork.kernel.org/project/netdevbpf/cover/20220517085143.3749-1-josua@solid-run.com/
Signed-off-by: Josua Mayer <josua@solid-run.com>
Currently, the adin driver fails to compile.
The original patch introducing the adin driver used the function
phy_get_interface_by_name to support the adi,phy-mode-override
property. Unfortunately, a few days before the adin patch
was accepted, another patch removed support for phy_get_interface_by_name:
123ca114e0
This patch refactors adin_get_phy_mode_override, implementing the logic in
the new function, ofnode_read_phy_mode, from the patch above.
Signed-off-by: Nate Drude <nate.d@variscite.com>
Tested-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Josua Mayer <josua@solid-run.com>
The pca9450 driver uses dm_i2c_{read,write}, which
are (unsurprisingly) only available with DM_I2C. Make sure one can't
create an unbuildable .config by adding proper dependencies.
While here, append "in SPL" to the prompt for the SPL_ variant so it
doesn't read the same as the one for the non-SPL_ variant.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Some of the DT compatibles have changed upstream so add new DT compatibles
to ensure things continue to keep working if the device trees are
updated.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add new lines to make errorr messages easier to read.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Introduce autogenerated SoC data support clk and device data for the
AM62. Hook it upto to power-domain and clk frameworks of U-Boot.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The AM62 SoC family is the follow on AM335x built on K3 Multicore SoC
architecture platform, providing ultra-low-power modes, dual display,
multi-sensor edge compute, security and other BOM-saving integration.
The AM62 SoC targets broad market to enable applications such as
Industrial HMI, PLC/CNC/Robot control, Medical Equipment, Building
Automation, Appliances and more.
Some highlights of this SoC are:
* Quad-Cortex-A53s (running up to 1.4GHz) in a single cluster.
Pin-to-pin compatible options for single and quad core are available.
* Cortex-M4F for general-purpose or safety usage.
* Dual display support, providing 24-bit RBG parallel interface and
OLDI/LVDS-4 Lane x2, up to 200MHz pixel clock support for 2K display
resolution.
* Selectable GPUsupport, up to 8GFLOPS, providing better user experience
in 3D graphic display case and Android.
* PRU(Programmable Realtime Unit) support for customized programmable
interfaces/IOs.
* Integrated Giga-bit Ethernet switch supporting up to a total of two
external ports (TSN capable).
* 9xUARTs, 5xSPI, 6xI2C, 2xUSB2, 3xCAN-FD, 3x eMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 3xMcASP for audio,
1x CSI-RX-4L for Camera, eCAP/eQEP, ePWM, among other peripherals.
* Dedicated Centralized System Controller for Security, Power, and
Resource Management.
* Multiple low power modes support, ex: Deep sleep,Standby, MCU-only,
enabling battery powered system design.
AM625 is the first device of the family. Add DT bindings for the same.
More details can be found in the Technical Reference Manual:
https://www.ti.com/lit/pdf/spruiv7
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for AM62x SoC identification.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The phy used in the 8 bit instance has been changed to the phy used in 4
bit instance on AM62 SoC. This implies the phy configuration required for
both the instances of mmc are similar. Therefore, add a new compatible
for AM62 SoC using the driver data of am64 4 bit instance.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
There is a TX-FIFO and Shift Register empty(TFES) status
bit in spi controller. This commit checks the TFES bit
to wait the TX transfer completes.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
DMSTART bit must not be set while there is active transfer.
This commit sets the DMSTART bit only when the transfer begins.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
synquacer_cs_set() function does not wait the chip select
is deasserted when the driver sets the DMSTOP to deselect
the slave.
This commit checks the Slave Select Released(SRS) bit to wait
until the slave is deselected.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
"busy" variable is ORed without being initialized,
must be zeroed before use.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
This uses the nvmem API to load a mac address from an RTC.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This uses an i2c eeprom to load a mac address using the nvmem interface.
Enable I2C_EEPROM for sandbox SPL since it is the only sandbox config
which doesn't enable it eeprom.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for "nvmem cells" as seen in Linux. The nvmem device
class in Linux is used for various assorted ROMs and EEPROMs. In this
sense, it is similar to UCLASS_MISC, but also includes
UCLASS_I2C_EEPROM, UCLASS_RTC, and UCLASS_MTD. New drivers corresponding
to a Linux-style nvmem device should be implemented as one of the
previously-mentioned uclasses. The nvmem API acts as a compatibility
layer to adapt the (slightly different) APIs of these uclasses. It also
handles the lookup of nvmem cells.
While nvmem devices can be accessed directly, they are most often used
by reading/writing contiguous values called "cells". Cells typically
hold information like calibration, versions, or configuration (such as
mac addresses).
nvmem devices can specify "cells" in their device tree:
qfprom: eeprom@700000 {
#address-cells = <1>;
#size-cells = <1>;
reg = <0x00700000 0x100000>;
/* ... */
tsens_calibration: calib@404 {
reg = <0x404 0x10>;
};
};
which can then be referenced like:
tsens {
/* ... */
nvmem-cells = <&tsens_calibration>;
nvmem-cell-names = "calibration";
};
The tsens driver could then read the calibration value like:
struct nvmem_cell cal_cell;
u8 cal[16];
nvmem_cell_get_by_name(dev, "calibration", &cal_cell);
nvmem_cell_read(&cal_cell, cal, sizeof(cal));
Because nvmem devices are not all of the same uclass, supported uclasses
must register a nvmem_interface struct. This allows CONFIG_NVMEM to be
enabled without depending on specific uclasses. At the moment,
nvmem_interface is very bare-bones, and assumes that no initialization
is necessary. However, this could be amended in the future.
Although I2C_EEPROM and MISC are quite similar (and could likely be
unified), they present different read/write function signatures. To
abstract over this, NVMEM uses the same read/write signature as Linux.
In particular, short read/writes are not allowed, which is allowed by
MISC.
The functionality implemented by nvmem cells is very similar to that
provided by i2c_eeprom_partition. "fixed-partition"s for eeproms does
not seem to have made its way into Linux or into any device tree other
than sandbox. It is possible that with the introduction of this API it
would be possible to remove it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
i2c_eeprom_ops->write uses a const buf, so use one for the wrapper
function as well.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of reading a pseudo-rom mac address from the device tree, just use
whatever we get from write_hwaddr. This has the effect of using the mac
address from the environment (or from the device tree, if it is
specified).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
Check the length of data written by the device is consistent with the
size of the buffers to avoid out-of-bounds memory accesses in case
values aren't consistent.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The virtio-rng driver is extremely simple, making it suitable for
testing more of the virtio uclass logic. Have the sandbox driver bind
the virtio-rng driver rather than the virtio-blk driver so it can be
used in tests.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The virtio sandbox transport was setting the device features value to
the bit index rather than shifting a bit to the right index. Fix this
using the bit manipulation macros.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the device returns used buffers, it should refer to the descriptor
that is the head of the descriptor chain for that buffer. Confirm this
to be the case by tracking the head of descriptor chains that have been
made available to the device.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The shared descriptors should only be written by the guest driver,
however, the device is still able to overwrite and corrupt them.
Maintain a private shadow copy of the descriptors for the driver to
use for state tracking, removing the need to read from the shared
descriptors.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the logic for attaching a descriptor to its own function.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The variables `total_sg` and `descs_used` have the same value. Replace
the few uses of `total_sg` with `descs_used` to simplify the situation.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds a driver for configuration of the Microchip USB251xB/xBi
USB 2.0 hub controller series with USB 2.0 upstream connectivity, SMBus
configuration interface and two to four USB 2.0 downstream ports.
This is ported from Linux as of Linux kernel commit
5c2b9c61ae5d8 ("usb: usb251xb: add boost-up property support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
This is used to avoid the ports status of IPPC being brought in kernel
stage, it may cause ports error especially when the xhci controller is
a component of dual-role controller.
Reported-by: Yun-Chien Yu <yun-chien.yu@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
CONFIG_VAL(DEBUG_UART_BASE) expands to CONFIG_DEBUG_UART_BASE or
CONFIG_SPL_DEBUG_UART_BASE or CONFIG_TPL_DEBUG_UART_BASE and allows boards
to set different values for SPL, TPL and U-Boot Proper.
For ns16550 driver this support is there since commit d293759d55
("serial: ns16550: Add support for SPL_DEBUG_UART_BASE").
Signed-off-by: Pali Rohár <pali@kernel.org>
Add a check for calloc() failing to allocate the requested memory.
Make decode_regions() return an error code.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_MMC only initializes drivers for devices in UCLASS_MMC, we need
to initialize drivers for devices of type IF_TYPE_MMC in UCLASS_BLK as
well because they are the child devices of devices in UCLASS_MMC. This
is required for feature RPMB since it will access eMMC in optee-os.
Signed-off-by: Judy Wang <wangjudy@microsoft.com>
[trini: Add my SoB line and adjust Judy's name in git, having emailed
off-list]
Signed-off-by: Tom Rini <trini@konsulko.com>
ARM semihosting provides no provisions for determining if there is
pending input. The only way to determine if there is console input is to
do a read (and block until the user types something). For this reason,
we always return true for tstc (since you will always get input if you
try). However, this behavior can cause problems for code which expects
tstc to eventually be empty. In query_console_serial, there is the
following construct:
/* empty input buffer */
while (tstc())
getchar();
with the current implementation, this effectively turns into an infinite
loop. To avoid this, fake tstc by returning false half of the time. This
is generally OK because the other common construct looks like
do {
if (tstc())
process(getchar());
} while (!timeout());
so it's fine if we only read a new character every other loop. This will
break things like CYGACC_COMM_IF_GETC_TIMEOUT, but that could be
reworked to test on the timeout instead of calling tstc again (and
ymodem over semihosted serial is not that useful in the first place).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Replace in the function of_machine_is_compatible(), the used API
fdt_node_check_compatible() by ofnode_device_is_compatible()
to support a live tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Set correct type for 3rd argument of ofnode_get_addr_size_index_notrans()
function. It expects fdt_size_t * and not fdt_addr_t *.
When these two types do not have same size then U-Boot throw compile
warning:
drivers/mtd/mtdpart.c: In function ‘add_mtd_partitions_of’:
drivers/mtd/mtdpart.c:906:57: warning: passing argument 3 of ‘ofnode_get_addr_size_index_notrans’ from incompatible pointer type [-Wincompatible-pointer-types]
offset = ofnode_get_addr_size_index_notrans(child, 0, &size);
^~~~~
In file included from include/dm/device.h:13,
from include/linux/mtd/mtd.h:26,
from include/ubi_uboot.h:28,
from drivers/mtd/mtdpart.c:27:
include/dm/ofnode.h:530:25: note: expected ‘fdt_size_t *’ {aka ‘long long unsigned int *’} but argument is of type ‘fdt_addr_t *’ {aka ‘long unsigned int *’}
fdt_size_t *size);
~~~~~~~~~~~~^~~~
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
We have many cases of SPL (or TPL or VPL) drivers that don't depend on
SPL_MISC (and so on) but rather just MISC.
Cc: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
CONFIG_DM_EVENT without CONFIG_EVENT is non-functional.
Let CONFIG_DM_EVENT depend on CONFIG_EVENT.
Remove superfluous stub in include/event.h.
Fixes: 5b896ed585 ("event: Add events for device probe/remove")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
CONFIG_FIXED_SDHCI_ALIGNED_BUFFER is needed on some Marvell SoCs when
booting from MMC. All existing usages of this have the same value so
make this the default and have the Kconfig option depend on SPL &&
MVEBU_SPL_BOOT_DEVICE_MMC.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SPL_SYS_MALLOC_SIMPLE
The problem here is that a few platforms have been doing:
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
instead of defining CONFIG_SPL_SYS_MALLOC_SIMPLE directly. Correct this
and update the documentation in a few places to match usage.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is always defined to 2, and referenced in two places. Move the
define to <asm/omap_common.h> and make sure the code that uses this
includes that file. Make <asm/arch-omap*/clock.h> not include that
file, as we don't need to be doing so.
Signed-off-by: Tom Rini <trini@konsulko.com>
If the device fails to probe - for example, when there is no
ethaddr set - then the private data is automatically freed
but the mdiobus remains registered.
Fixes: 1e354cb393 ("drivers: net: fsl_enetc: register internal MDIO bus")
Signed-off-by: Michael Walle <michael@walle.cc>
This driver depends on PCI. Update the Kconfig accordingly.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYo4bYwAKCRDKSWXLKUoM
IYmTAJ9t4GDXggJ7ErB3Kk7/qSrywjEGAgCgnKQVgQvjo1B6o5aiwbk1wR86zkQ=
=W7X8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc4' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc4
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
The bulk of it is (finally!) some DT sync from the kernel. We refrained
from syncing one incompatible change, as this would spoil booting Linux
kernels before v5.13 with U-Boot's DT (via UEFI, for instance).
I test booted Linux v5.18 and v5.4 with that new DT on some boards, and
the headless peripherals (MMC, USB, Ethernet) seemed to work.
The rest are fixes:
- silencing missing clock warnings due to the new pinctrl driver
- fixing "UART0 on PortF", allowing UART access through the SD card pins
- add an F1C100s clock driver, to enable MMC support (SPI comes later)
- some cleanups for CONS_INDEX_n in Kconfig
Tested on BananaPi-M1, Pine64-LTS, Pine-H64, X96-Mate (H616) and
OrangePi-Zero.
These were only ever implied by sunxi platforms, and that usage has
been removed. Current practice is to specify CONFIG_CONS_INDEX in each
board's defconfig.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Some devices enumerate various clocks in their DT, and many drivers
just blanketly try to enable all of them. This creates problems
since we only model a few gate clocks, and the clock driver outputs
a warning when a clock is not described:
=========
sunxi_set_gate: (CLK#3) unhandled
=========
Some clocks don't have an enable bit, or are already enabled in a
different way, so we might want to just ignore them.
Add a CCU_CLK_F_DUMMY_GATE flag that indicates that case, and define
a GATE_DUMMY macro that can be used in the clock description array.
Define a few clocks, used by some pinctrl devices, that way to suppress
the runtime warnings.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
The introduction of the DM pinctrl driver made its probe function enable
all clocks enumerated in the DT. This includes the "CLK_BUS_PIO" (and
variations) gate clock. Also CLK_PLL_PERIPH0 is used by the R_CCU device.
So far we didn't describe those clocks in our clock driver.
As we enable them already in the SPL, the devices happen to work, but
the clock driver still complains about not finding those clocks:
=========
sunxi_set_gate: (CLK#58) unhandled
=========
Add the one-liners that are needed to announce the gate bit for those
clocks, to silence that message on the console.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
H6 is from the sun50i family, not sun6i.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that the pinmux conflict is handled in the board code (by skipping
setup for the one conflicting MMC controller), the driver does not need
to be entirely disabled based on the UART pinmux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add the tpm2_tis_i2c driver that should support any TPMv2 compliant
I2C chips, such as the NPCT75X chip.
[Ilias rename priv_auto_alloc_size to priv_auto]
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Commit 0980cbba7b ("mmc: fsl_esdhc_spl: pre-PBL: implement redundancy
support") changed number of sectors which are read but did not adjusted
error check.
Fix it and check for if correct number of sectors were read.
Fixes: 0980cbba7b ("mmc: fsl_esdhc_spl: pre-PBL: implement redundancy support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Now, spi_flash_probe_bus_cs() relies on DT for spi speed and mode
and logically calls spi_get_bus_and_cs(). In case spi mode and speed are
not read from DT, make usage of spi_flash_probe() instead.
To sum-up:
- Previous call tree was:
spi_flash_probe() -> spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
- Current call tree is:
spi_flash_probe() -> _spi_get_bus_and_cs()
spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
This patch impacts the following :
- cmd/sf.c: if spi mode and/or speed is passed in argument of
do_spi_flash_probe(), call spi_flash_probe() otherwise call
spi_flash_probe_bus_cs().
- drivers/net/fm/fm.c: as by default spi speed and mode was set to
0 and a comment indicates that speed and mode are read from DT,
use spi_flash_probe_bus_cs().
- drivers/net/pfe_eth/pfe_firmware.c: spi speed and mode are not read
from DT by all platforms using this driver, so keep legacy and replace
spi_flash_probe_bus_cs() by spi_flash_probe();
- drivers/net/sni_netsec.c : spi speed and mode are not read from DT,
so replace spi_flash_probe_bus_cs() by spi_flash_probe().
- drivers/usb/gadget/max3420_udc.c: Can't find any platform which make
usage of this driver, nevertheless, keep legacy and replace
spi_get_bus_and_cs() by _spi_get_bus_and_cs().
- env/sf.c: a comment indicates that speed and mode are read
from DT. So use spi_flash_probe_bus_cs().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Move legacy spi_get_bus_and_cs() code to _spi_get_bus_and_cs().
Add new spi_get_bus_and_cs() implementation which rely on DT
for speed and mode and don't need any drv_name nor dev_name
parameters. This will prepare the ground for next patch.
Update all callers to use _spi_get_bus_and_cs() to keep the
same behavior.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Requesting the locality uses the timeout values, so they need
to be set beforehand.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add support for reading GPIO pin value when function is output.
With this patch applied, gpio toggle command is working.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The f1c100s has a clock tree similar to those of other sunxi parts.
Add support for it.
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Yifan Gu <me@yifangu.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
[Andre: add PIO and I2C]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Missing nodes may also be signaled via -ENODATA. We need to check for
that to prevent failing in non-usb3 setups.
Furthermore, dev.phy must be NULL'ed in case usb3-phy was not found.
Fixes: 142d50fbce ("usb: dwc3: Add support for usb3-phy PHY configuration")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add PCA9450 regulator driver. This is complementary driver for the BUCKn
and LDOn regulators provided by the PCA9450 PMIC driver. Currently the
driver permits reading the settngs and configuring the BUCKn and LDOn
regulators.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The upstream DT regulators node subnodes are named BUCKn and LDOn,
the downstream DT regulators node subnodes are named buckn and ldon,
add the upstream match.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The specific implementation was having bug. Those bugs are since
the beginning of the implementation. Some manufactures can already
experience this bug in their SPL code. This bug can be more visible on
architecture that has complicated boot process like imx8mn. Older
version of uboot can be affected if the bad block
appear in correspoding of the beginning of u-boot image. In order to
adjust the function we scan from the first erase block.
The problematic part of old code was in this part:
while (is_badblock(mtd, offs, 1)) {
page = page + nand_page_per_block;
/* Check i we've reached the end of flash. */
if (page >= mtd->size >> chip->page_shift) {
free(page_buf);
return -ENOMEM;
}
}
Even we fix it adding increment of the offset of one erase block size
, we don't fix the problem, because the first erase block where the
image start is not checked. The code was tested on an imx8mn where
the boot rom api was not able to skip it. This code is used by other
architecures like imx6 and imx8mm
Cc: Han Xu <han.xu@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Move the hook after nand_scan_tail is called. The hook must be replaced
to the mxs specific one but those must to be assignment later in the
probe function.
With this fix markbad is working again. Before this change:
nand markbad 0xDEC00
NXS NAND: Writing OOB isn't supported
NXS NAND: Writing OOB isn't supported
block 0x000dec00 NOT marked as bad! ERROR 0
Cc: Han Xu <han.xu@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
implement get f/w version api.
print ele f/w version in spl.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@nxp.com>
When the device tree indicates support for role switching through
the "usb-role-switch" property, take the "role-switch-default-mode"
property into account when deciding which role to put the
controller into.
This makes USB devices work on Apple M1 systems where the device
tree may include a "dr_mode" property that is set to "otg", but
where we need to put the controller into "host" mode to see
devices connected to the type-C ports.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
I was trying to employ lpddr4_mr_read() to something similar to what
the imx8mm-cl-iot-gate board is doing for auto-detecting the RAM
type. However, the version in drivers/ddr/imx/imx8m/ddrphy_utils.c
differs from the private one used by that board in how it extracts the
byte value, and I was only getting zeroes. Adding a bit of debug
printf'ing gives me
tmp = 0x00ffff00
tmp = 0x00070700
tmp = 0x00000000
tmp = 0x00101000
and indeed I was expecting a (combined) value of 0xff070010 (0xff
being Manufacturer ID for Micron). I can't find any documentation that
says how the values are supposed to be read, but clearly the iot-gate
definition is the right one, both for its use case as well as my
imx8mp-based board.
So lift the private definition of lpddr4_mr_read() from the
imx8mm-cl-iot-gate board code to ddrphy_utils.c, and add a declaration
in the ddr.h header where e.g. get_trained_CDD() is already declared.
This has only been compile-tested for the imx8mm-cl-iot-gate
board (since I don't have the hardware), but since I've merely moved
its definition of lpddr4_mr_read(), I'd be surprised if it changed
anything for that board.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
RNG Hardware error is reported due to incorrect entropy delay
rng self test are run to determine the correct ent_dly.
test is executed with different voltage and temperature to identify the
worst case value for ent_dly. after adding a margin value(1000),
ent_dly should be at least 12000.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Because mxs_nand_spl driver does not support DM, to use the minimum ECC
layout, it needs to handle the CONFIG_NAND_MXS_USE_MINIMUM_ECC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Han Xu <han.xu@nxp.com>
Waiting for SR_BUSY bit when receiving a new command is not needed.
SR_BUSY bit is already managed in the previous command treatment.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Currently, SR_TCF flag is checked in case there is data, this criteria
is not correct.
SR_TCF flags is set when programmed number of bytes have been transferred
to the memory device ("bytes" comprised command and data send to the
SPI device).
So even if there is no data, we must check SR_TCF flag.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Observing psgtr pll timeouts with some usb hubs and devices behind it.
Increase timeout to 10ms to take care of it.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220510131234.2650-1-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Currently, pinctrl drivers only get probed if pinconf is actually being
used, however on SoC-s like Armada 3720 pinctrl driver is a also the GPIO
driver.
So, if the pinctrl driver doesn't get probed GPIO-s won't get registered
and thus they cannot be used.
This is a problem on the Methode eDPU as it just uses SB pins as GPIO-s
and without them being registered networking won't work as it only has
one SFP slot and the TX disable GPIO is on the SB controller.
So, probe the pinctrl drivers using DM_FLAG_PROBE_AFTER_BIND like LED
uclass does.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Use CONFIG_VAL(DEBUG_UART_BASE) instead of CONFIG_DEBUG_UART_BASE, so
proper config value (CONFIG_DEBUG_UART_BASE or CONFIG_SPL_DEBUG_UART_BASE)
is used based on building target.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
TPL_DEBUG_UART_BASE is same as DEBUG_UART_BASE, but applies only for TPL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Stefan Roese <sr@denx.de>
SPL_DEBUG_UART_BASE is same as DEBUG_UART_BASE, but applies only for SPL.
In some cases base address of UART is different in SPL and proper U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
zynqmp_pm_is_function_supported() which checks feature support on som,
which is implemented in firmware_zynqmp.c driver. As mini configuration
does not use firmware driver, so create a weak function to avoid
compilation error on zynqmp mini configuration.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/c60655a509956b8fc3a81671a7dc51157f3973db.1651048030.git.michal.simek@xilinx.com
