This patch removes CONFIG_SYS_DSPI_XX options from
include/configs "m68k" .h board files, since CTAR
registers are now set with default values in the cf_spi
driver initialization, and configurable by devicetree.
Note, these options cannot be totally removed from the
whitelist, since still used from boards using fsl_dspi.c
(mostly arm-based boards).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
This patch adds devicetree support to the mcfuart.c driver
and removes non DM code.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
This patch adds CONFIG_DM_SPI for all m68k boards using
the cf_spi.c driver (DSPI module).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Enable DT usage for all m68k boards. To provide a
working single binary, the dts has been kept as embedded.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
This patch adds basic dts files for all the m68k boards.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
[trini: Add CONFIG_TARGET_M5329EVB dtbs and update M5329EVB defconfigs]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds a basic group of devicetrees, one for each
cpu family, including actually just uart and dspi devices,
since these are the drivers supporting devicetree (support
added in this patch-set).
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
On SoCFPGA A10 systems, it can rarely happen that a reboot from Linux
will result in stale data in PL310 L2 cache controller. Even if the L2
cache controller is disabled via the CTRL register CTRL_EN bit, those
data can interfere with operation of devices using DMA, like e.g. the
DWMMC controller. This can in turn cause e.g. SPL to fail reading data
from SD/MMC.
The obvious solution here would be to fully reset the L2 cache controller
via the reset manager MPUMODRST L2 bit, however this causes bus hang even
if executed entirely from L1 I-cache to avoid generating any bus traffic
through the L2 cache controller.
This patch thus configures and enables the L2 cache controller very early
in the SPL boot process, clears the L2 cache and disables the L2 cache
controller again.
The reason for doing it in SPL is because we need to avoid accessing any
of the potentially stale data in the L2 cache, and we are certain any of
the stale data will be below the OCRAM address range. To further reduce
bus traffic during the L2 cache invalidation, we enable L1 I-cache and
run the invalidation code entirely out of the L1 I-cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Pull the PL310 clearing code into common code, so it can be reused
by Arria10.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
commit 1b898ffc04 ("gpio: dwapb_gpio: convert to livetree") introduced
a bug in that dev->node of the gpio chip was accidentally set to the
of_node of its bank subnode.
What it meant to do was assign subdev->node, not dev->node.
While this doesn't affect too many use cases, iterating over the gpio
chip's properties doesn't work any more after that, so fix this.
Fixes: commit 1b898ffc04 ("gpio: dwapb_gpio: convert to livetree")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Enable eSDHC, SATA and USB DM for T2080QDS in uboot
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch is to support Freescale sata driver with dts initialized.
Also resolved the following problems.
===================== WARNING ======================
This board does not use CONFIG_DM_SCSI. Please update
the storage controller to use CONFIG_DM_SCSI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
adopt 32 bit addr in fsl_esdhc for CONFIG_PPC.
So adopt 32 bit address for CONFIG_PPC.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add command tuning for DDR interactive mode, used during
board bring-up or with CubeMX DDR tools to execute software
tuning for the DDR configuration:
- software read DQS Gating (replace the built-in one)
- Bit de-skew
- Eye Training or DQS training
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add command tests for DDR interactive mode, used during
board bring-up or with CubeMX DDR tools to verify the
DDR configuration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This debug mode is used by CubeMX DDR tuning tools
or manualy for tests during board bring-up.
It is simple console used to change DDR parameters and check
initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Manage power supply configuration for board using stpmic1
with LPDDR2 or with LPDDR3:
+ VDD_DDR1 = 1.8V with BUCK3 (bypass if possible)
+ VDD_DDR2 = 1.2V with BUCK2
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Force alignment of the size of parameters array with
the expected value in the binding, that allows compilation
error when the array size change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update DDR configuration with the latest update:
- PUBL_regs: DXnGCR[0]= according to ddr_width to disable Byte
lane 2/3 in 16bit
- fix LPDDR2/3 timing_calc to step RL/WL in relaxed
timings mode
- remove LPDDR3 RL3 (optional) support vs MR0[7]
because MR0[7] can't be read instead always apply
worse RL/WL for LPDDR3 when freq < 166MHz)
- change MR3 to 48ohm drive for LPDDR2/3
- change default ZPROG[7:4] = 0x1 for LPDDR2/3 ,
'0' is not allowed even when ODT not used
- use DQSTRN for LPDDR2/3 (it was not set in PIR)
- LPDDR3: set dqsge/dwsgx gate extension to 2,2
like LPDDR2
-DDRCTRL.dfitmg0:
+ for LPDDR3 tphy_wrlat = WL (as LPDDR2)
+ improvement for relaxed mode vs RL/Wl at corner case.
For example @533MHz RL/WL (relaxed) = 9/5 for LPDDR2/3
and correction to MR2 accordingly
- DDR_PCFGQOS1_1: port1 timeout relaxed from 0x00 to 0x40,
for LTDC.
- DDR_PCFGWQOS0_0: change vpr level from
11 to 12 in order to include the CPU on
the variable priority queue.
- DDR_SCHED: fix to consider 13 levels (13 levels - 1 = 0xC)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Component Notification DDR controller errata (3.00a):9001313030
Synchronization Time Waited After De-assertion of presetn is
128 pclk Cycles.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
For STM32MP, the watchdog is based on DM and the function watchod_reset
call the function uclass_get_device(UCLASS_WDT) to found the driver
associated IWDG2.
As this reset is not mandatory in debug putc (the uart fifo will be
empty after some us), we can simplify the code by removing this call.
And this patch avoid issue when putc is called before initialization
of DM core, before the parsing of the device tree parsing and each
node bound to driver; that also avoid memory leak.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Solve compilation issue when cli_simple.o is used in SPL
and CONFIG_SPL_ENV_SUPPORT is not defined.
env/built-in.o:(.data.env_htab+0xc): undefined reference to `env_flags_validate'
u-boot/scripts/Makefile.spl:384: recipe for target 'spl/u-boot-spl' failed
make[2]: *** [spl/u-boot-spl] Error 1
u-boot/Makefile:1649: recipe for target 'spl/u-boot-spl' failed
make[1]: *** [spl/u-boot-spl] Error 2
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the needed configurations for bootstage and
activate bootstage command.
BOOTSTAGE_REPORT is not activated by default.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
In initf_bootstage() we call bootstage_mark_name() which ends up calling
timer_get_us() before timer_init(); that cause crash for stm32mp1.
This patch solve the issue without changing the initialization sequence.
See also commit 97d20f69f5 ("Enable CONFIG_TIMER_EARLY with bootstage")
for other solution when DM is activated for TIMER.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
To get more information from STM32 Header about the generated binary,
we will add a new byte with the following field:
replace padding byte 255 with 0x00 for "U-Boot"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This avoids useless loops inside the I2C timing algorithm.
Actually, we support only one possible solution per prescaler value.
So after finding a solution with a prescaler, the algorithm can
switch directly to the next prescaler value.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
It conforms with Reference Manual I2C timing section.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use SGI0 interruption and TAMP_BACKUP_MAGIC_NUMBER
to synchronize the core1 boot sequence requested by
core0 in psci_cpu_on():
- a initial interruption is needed in ROM code after
RCC_MP_GRSTCSETR_MPUP1RST (psci_cpu_off)
- the ROM code set to 0 the 2 registers
+ TAMP_BACKUP_BRANCH_ADDRESS
+ TAMP_BACKUP_MAGIC_NUMBER
when magic is not egual to
BOOT_API_A7_CORE0_MAGIC_NUMBER
This patch solve issue for cpu1 restart in kernel.
echo 0 > /sys/devices/system/cpu/cpu1/online
echo 1 > /sys/devices/system/cpu/cpu1/online
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch moves the the config SYS_MALLOC_LEN to
Kconfig as it is already done for zynq arch in
commit 01aa5b8f05 ("Kconfig: Move config
SYS_MALLOC_LEN to Kconfig for zynq")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
PowerPC supports 32 bit address.
So adopt 32 bit addr in fsl_esdhc for CONFIG_PPC.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Changes from rc2 tag
- Support PCIe Gen4 driver of the Mobiveil IP
- NXP LS1028A SoC and platform support
- Few SPI related config updates
- Distinguish the ecc val by chassis version and move the ecc addr to dts
- sp805 watchdog support
