Lichee Pi Zero is a development board with a V3s SoC, which features
64MiB DRAM co-packaged within the SoC, a TF slot, a SPI NOR slot (not
soldered in production batch), a 40-pin RGB LCD connector and some extra
pins available as 2.54mm pins or stamp holes.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Basic U-Boot support is now present for V3s.
Some memory addresses are changed specially for V3s, as the original
address map cannot fit into a so small DRAM.
As the DRAM controller code needs a big refactor, the SPL support is
disabled in this version.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is needed for HDMI, which will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Bananapi M2 Ultra is the first publicly available development board
featuring the R40 SoC.
This patch add barebone dtsi/dts files for the R40 and Bananapi M2 Ultra,
as well as a defconfig for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40's CPU controls are a combination of sun6i and sun7i.
All controls are in the CPUCFG block, and it seems the R40 does not
have a PRCM block. The core reset, power gating and clamp controls
are grouped like sun6i.
Last, the R40 does not have a secure SRAM block.
This patch adds a PSCI implementation for CPU bring-up and hotplug
for the R40.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we can do DRAM initialization for the R40, we can enable
SPL support for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These values were taken from the Banana Pi M2 Ultra fex file
found in the released vendor BSP. This is the only publicly
available R40 device at the time of this writing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PIO is generally compatible with the A20, except that it routes the
full 8 bits and eMMC reset pins for mmc2.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 SoC uses the AXP221s in I2C mode to supply power.
Some regulator's common usages have changed, and also the recommended
voltage for existing usages have changed. Update the defaults to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 is the successor to the A20. It is a hybrid of the A20, A33
and the H3.
The R40's PIO controller is compatible with the A20,
Reuse the A20 UART and I2C muxing code by adding the R40's macro.
The display pipeline is the newer DE 2.0 variant.
Block enabling video on R40 for now.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently we have some lines in board/sunxi/Kconfig that are very long.
These line either provide default values for a set of SoCs, or limit
some option to a subset of sunxi SoCs.
Fortunately Kconfig makes it easy to split them. The Kconfig language
document states
If multiple dependencies are defined, they are connected with '&&'.
This means we can split existing dependencies at "&&" symbols. This
applies to both the "depends on" lines and "if" expressions.
This patch splits them up to one symbol per line. This will make it
easier to add, remove, or modify one item at a time.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONFIG_MACPWR to Kconfig and update all the sunxi defconfigs
that used it in SYS_EXTRA_OPTIONS.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONFIG_SATAPWR into kconfig.
Thanks to that, many SYS_EXTRA_OPTIONS can be removed from some
defconfigs.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Sunchip CX-A99 is a board used in some media players. It features:
An Allwinner A80 ARM SoC (4 * Cortex-A7 + 4 * Cortex-A15 cores)
2 GiB or 4 GiB DDR3 DRAM
AXP808 PMIC
16 GB or 32 GB eMMC
SDIO Wifi/Bluetooth/FM module
SD card slot
1 USB 3.0 connector
2 USB 2.0 connectors
SATA connector
UART connector (internally) for serial console
Ethernet connector (10/100/1000 Mbit/s)
HDMI connector
Composite video and analog audio connector
S/PDIF connector
IR remote control receiver
This patch adds a defconfig for the board. The DRAM settings are as found
in the vendor sys_config.fex file.
It has a preliminary device tree for use until a device tree is accepted
upstream, after which it can be replaced by the upstream version.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
[squash commits, and edited new meanful commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Introduce a new sunxi-spl-with-ecc.bin image with already the right header,
ECC, randomizer and padding for the BROM to be able to read it.
It needs to be flashed using a raw access to the NAND so that the
controller doesn't change a thing to it, since we already have all the
right parameters.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The OrangePi PC 2 is a typical SBC with the 64-bit Allwinner H5 SoC.
Add a (64-bit only) defconfig defining the required options to build
the U-Boot proper.
Create a new .dts file for it by including the (32-bit) H3 SoC .dtsi
and changing the differing components accordingly.
This is a preliminary device tree mostly for U-Boot's own sake, it
is expected to be updated once the official DT gets accepted upstream.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[squash the commits, update the commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner H5 Soc is bascially an H3 with high SRAM and ARMv8 cores.
As the peripherals and the pinmuxing are almost identical, we piggy
back on the shared MACH_SUN8I_H3_H5 config symbol.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Traditionally Allwinner SoCs have their boot ROM mapped just below 4GB,
while the first SRAM region is mapped at address 0.
With the extended physical memory support of the A80 this was changed,
so the BROM is now at address 0 and the SRAM region starts right behind
this at 64KB. This configuration seems to be called "high SRAM".
Instead of enumerating the SoCs which have copied this configuration,
let's call a spade a spade and introduce a Kconfig option for this setup.
SoCs implementing this (A80, A64 and H5, so far), can then select this
configuration.
Simplify the config header definition on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Instead of enumerating all SoC families that need that bit set, let's
just express this more clearly: The SMP bits needs to be set on
SMP capable ARMv7 CPUs. It's much easier in Kconfig to express it the
other way round, so we use ! CPU_IS_UP and ! ARM64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Many ARMv8 boards define a constant COUNTER_FREQUENCY to specify the
frequency of the ARM Generic Timer (aka. arch timer).
ARMv7 boards traditionally used CONFIG_TIMER_CLK_FREQ for the same
purpose. It seems useful to unify them.
Since there are less occurences of the latter version, lets convert all
users over to COUNTER_FREQUENCY.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Orange Pi Zero is a board designed by Xunlong. It has an Allwinner H2+
SoC (similar to H3, which shares the same SoC ID), 256MB/512MB RAM,
Allwinner XR819 SDIO Wi-Fi, a MicroUSB port which is used to power the
board (also capable of OTG), a USB Type-A socket and a MicroSD slot.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The bare default entry is wrong. Just remove it since the (real)
entry in drivers/mmc/Kconfig has "default ARM || PPC || SANDBOX".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Now that the SPL is ready to be compiled in AArch64 and the DRAM
init code is ready, enable SPL support for the A64 SoC and in the
Pine64 defconfig.
For now we keep the boot0 header in the U-Boot proper, as this allows
to still use boot0 as an SPL replacement without hurting the SPL use
case.
We disable FEL support for now by making its compilation conditional
and disabling it for ARM64, as the code isn't ready yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
To avoid enumerating the very same DRAM values in defconfig files
for each and every Allwinner A64 board out there, let's put some sane
default values in the Kconfig file.
Boards with different needs can override them at any time.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner A64 SoC starts execution in AArch32 mode, and both
the boot ROM and Allwinner's boot0 keep running in this mode.
So U-Boot gets entered in 32-bit, although we want it to run in AArch64.
By using a "magic" instruction, which happens to be an almost-NOP in
AArch64 and a branch in AArch32, we differentiate between being
entered in 64-bit or 32-bit mode.
If in 64-bit mode, we proceed with the branch to reset, but in 32-bit
mode we trigger an RMR write to bring the core into AArch64/EL3 and
re-enter U-Boot at CONFIG_SYS_TEXT_BASE.
This allows a 64-bit U-Boot to be both entered in 32 and 64-bit mode,
so we can use the same start code for the SPL and the U-Boot proper.
We use the existing custom header (boot0.h) functionality, but restrict
the existing boot0 header reservation to the non-SPL build now. A SPL
wouldn't need such header anyway. This allows to have both options
defined and lets us use one for the SPL and the other for U-Boot proper.
Also add arch/arm/mach-sunxi/rmr_switch.S, which contains the original
ARM assembly code and instructions how to re-generate the encoded
version.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The ENABLE_ARM_SOC_BOOT0_HOOK option is a generic option shared with
other boards. To allow alternative code to be inserted, we create
another, now function specific config symbol on top of it to simplify
later additions. No functional change at this time.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add board support for sun8i_r16 Nintendo NES Classic edition.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
[jagan: Add commit message body]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Cubieboard4 is an A80 SoC based development board from Cubietech.
This board has a UART port, 4 USB host ports, a USB 3.0 OTG connector,
HDMI and VGA outputs, a micro SD slot, 8G eMMC flash, 2G DRAM, a WiFi/BT
combo chip, headphone and microphone jacks, IR receiver, and GPIO headers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A80 Optimus Board was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.
This board has a UART port, a JTAG connector, 2 USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 16G eMMC flash,
2G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: update existing Merrii_A80_Optimus_defconfig
instead of adding a new defconfig]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Both the A80 Optimus board and the Cubieboard 4 use a zq value of
4145117, or 0x3f3fdd.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In Allwinner's SDK the A80 is clocked to 1008 MHz by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A80 can support 8-bit eMMC with reset on the PC pingroups.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that DRAM initialization and clock setup is supported,
we can enable SPL for the A80.
[wens@csie.org: Added commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds DRAM initialisation code for sun9i, which calculates the
appropriate timings based on timing information for the supplied
DDR3 bin and the clock speeds used.
With this DRAM setup, we have verified DDR3 clocks of up to 792MHz
(i.e. DDR3-1600) on the A80-Q7 using a dual-channel configuration.
[wens@csie.org: Moved dram_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: Drop some huge non-documenting #if 0 ... #endif blocks]
[hdegoede@redhat.com: Fix checkpatch warnings]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Move the config IDENT_STRING to Kconfig and migrate all boards
[sivadur: Migrate zynq boards]
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[trini: Update configs, add some default to sunxi Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
The NanoPi NEO is a simple h3 board with 512MB RAM, ethernet, one usb
and one usb OTG connector.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add ARCH_SUPPORT_PSCI as a non-configurable option that platforms
can select. Then, move CONFIG_ARMV7_PSCI, which is automatically
enabled if both ARMV7_NONSEC and ARCH_SUPPORT_PSCI are enabled.
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Casting "int"s to pointers is only valid for 32-bit systems.
Add the appropriate pointer type cast to avoid a compiler warning
when compiling for AArch64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
There is no "CONFIG_MACH_SUN50I_A64" in upstream U-Boot, so fix
the name to prevent the option to be enabled.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus,
with 2G RAM and an external gbit ethernet phy.
The dts file is identical to the one submitted to the upstream kernel,
except that it has the pending patch to enable the ethernet controller
squashed in, as u-boot already has sun8i-emac support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
A33-OLinuXino is A33 development board designed by Olimex LTD.
It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.
It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The iNet D978 rev2 is a tablet board designed by iNet, which is intended to
use on 10" tablets with a appearance like Apple iPad. It has A33 SoC, 1GB
RAM, 8GB/16GB NAND, SDIO Wi-Fi, a MicroUSB port and a MicroSD slot.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a defconfig and dts file for the Empire Electronix M712 tablet, this
is a 7" A13 tablet, with micro-usb (otg), headphone and micro-sd slots on
the outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a defconfig and dts file for tablets using the generic inet-q972 PCB.
Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.
This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Linux stopped the use of keyword 'boolean' in Kconfig.
Refer to commit 6341e62b212a2541efb0160c470e90bd226d5496 ("kconfig:
use bool instead of boolean for type definition attributes")
in Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
It seems that bytes 13-14 of the SID / bytes 1-2 from word 3 of the SID
are always 0 on H3 making it a poor candidate to use as source for the
serialnr / mac-address, and the other non constant words (1 and 2) also
have quite a few bits which are the same for some boards,
This commits switches to using the crc32 of words 1 - 3 to get a
more unique value for the mac-address / serialnr.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On 2 of my H3 boards bytes 13-15 of the SID are all 0 leading to
the NIC specific bytes of the mac all being 0, which leads to the
boards not getting an ipv6 address from the dhcp server.
This commits adds a check to ensure this does not happen.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
There is a new Orange Pi PC *Plus* version available now,
this is an extended version of the regular Orange Pi PC
with sdio wifi and an eMMC.
The upstream kernel devs have decided that they want a separate
dts for the PC Plus rather then sharing a single dts between the
regular PC and the PC Plus. So add a new orangepi_pc_plus_defconfig
to match.
The added dts file matches the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We already have an SPL driver for the sunxi NAND controller, now add
the normal/standard one.
The source has been copied from Linux 4.6 with a few changes to make
it work in u-boot.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that we know that the BROM stores a value indicating the boot-source
at the beginning of SRAM, use that instead of trying to recreate the
BROM's boot probing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We always define CONFIG_MISC_INIT_R on sunxi and misc_init_r is never
called in the spl, so the linker will optimize it and parse_spl_header(),
of which it is the only caller, away.
On the tests I've done (Orange Pi PC build) the SPL actually becomes
8 bytes smaller with this patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Currently we fill ethaddr with a fixed unique address based on the SoCs
serial (from the sid) to make sure that boards which use the integrated
emac / gmac get a fixed mac rather then a random one.
On some boards the wifi does not come with a fixed mac either, so we need
to also set eth1addr.
This commit changes the ethaddr setting code to check for ethernet%d
aliases (as fdt_fixup_ethernet does) and set an ethaddr variable for
all present aliases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The patch converts one of the "reserved" fields in the sunxi SPL
header to a fel_uEnv_length entry. When booting over USB ("FEL
mode"), this enables the sunxi-fel utility to pass the string
length of uEnv.txt compatible data; at the same time requesting
that this data be imported into the U-Boot environment.
If parse_spl_header() in the sunxi board.c encounters a non-zero
value in this header field, it will therefore call himport_r() to
merge the string (lines) passed via FEL into the default settings.
Environment vars can be changed this way even before U-Boot will
attempt to autoboot - specifically, this also allows overriding
"bootcmd".
With fel_script_addr set and a zero fel_uEnv_length, U-Boot is
safe to assume that data in .scr format (a mkimage-type script)
was passed at fel_script_addr, and will handle it using the
existing mechanism ("bootcmd_fel").
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Since we lack information about the DRAM initialization for the
Allwinner A64 SoC, booting any A64 based board like the Pine64 is a bit
involved at the moment.
Add a README file to explain the process.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Move to board/sunxi/ from doc/]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
The DTS file is identical to the one submitted to the upstream kernel.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The switch to simple_printf was causing the SPL dram info to show as:
DRAM: u MiB
This fixes this by switching from %lu to %d for printing the DRAM size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This reverts commit 1a5f0de08e86("sunxi: make SoC variant choice
mandatory").
With the optional marking in the Kconfig "make savedefconfig"
will drop CONFIG_MACH_SUN4I=y from all the A10 boards, making it
hard to see at a glance which family of sunxi chips the defconfig
is for.
This commit therefore restores the optional, and restores
CONFIG_MACH_SUN4I=y to all defconfig's which had it dropped
because of this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The inet86dz board is a board used in 7" tablets from various oems.
These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
The dts file this commit adds is identical to the one submitted to
the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.
Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The ARM Trusted Firmware (ATF) code now lives in SRAM on the Pine64/A64,
so we can claim the whole of DRAM for OS use.
This reverts commit 3ffe39ed2b.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A80 uses the AXP809 as its primary PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The AXP818 has a switchable output, SW. This is commonly used for
controlling power to the LCD backlight.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The newer chips use a newer display pipeline, which is not supported.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
A83T, H3, and A64 have a dedicated pin for card detect on the PF
pingroup. This is used in all designs. Set it as the default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In most other places, we sort SoC descriptions by family (sunXi) first,
then by the chip name (A20).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The user should always select an SoC variant to support. Not choosing
one doesn't make sense for a bootloader.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Orange Pi One SBC, is a stripped down version of the popular
Orange Pi PC. The one is a H3 based SBC, with 512M of RAM,
micro-sd slot, 1 host usb, 1 otg usb, hdmi and 100Mbit ethernet.
The dts is identical to the dts submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some boards have on board usb devices which need longer than the USB
spec's 1 second to connect from board powerup. Add a config option which
when non 0 adds an extra delay before the first usb bus scan.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On the A64 we usually boot with ATF running in EL3. ATF as it is available
today resides in the first 16MB of RAM. So we should make sure we reserve
that space in our memory maps.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Pine64+ is a system based on the Allwinner A64 SoC. It is capable of
running AArch64 code and thus is the first of its kind for the sunxi target.
This patch adds a defconfig and device tree chunks for it.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: Change patch description]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Allwinner A64 SoC is used in the Pine64. This patch adds
all bits necessary to compile U-Boot for it running in AArch64
mode.
Unfortunately SPL is not ready yet due to legal problems, so
we need to boot using the binary boot0 for now.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: remove SPL code, move to AArch64]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The FLDOs on AXP818 PMIC normally provide power to CPUS and USB HSIC PHY
on the A83T/H8.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Always select OF_BOARD_SETUP on sunxi, rather then having it in almost
all our defconfigs. This also fixes it missing from some recently
added defconfigs.
This commit also modifies our ft_board_setup() to not cause warnings
when CONFIG_VIDEO_DT_SIMPLEFB is not set, since we will now always
build it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
There are 2 reasons for doing this:
1) The main reason for doing this is to move it outside of
board/sunxi/ahci.c, so that it can be used on boards which use
a usb<->sata chip too;
2) While doing this I realized that doing it from board_init also meant
doing it much earlier. Some printf get_timer(0) calls show that the
time between board_init() and scsi_init() is more then 600 ms,
so we can drop the mdelay(500)
While at it also drop the printf("SUNXI SCSI INIT\n") AHCI init is
noisy enough by itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
cpu_eth_init is no longer called for dm enabled eth drivers, this
was causing the sunxi gmac eth controller to no longer work in u-boot.
This commit fixes this by calling the clock, reset and pinmux setup
function from s_init() and enabling the phy power pin (if any) from
board_init().
The enabling of phy power cannot be done from s_init because it uses dm
and dm is not ready yet at this point.
Note that the mdelay is dropped as the phy gets enabled much earlier
now, so it is no longer needed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Karsten Merker <merker@debian.org>
Tested-by: Michael Haas <haas@computerlinguist.org>
The H3 has USB0 - USB3, add support for having a USB vbus pin for USB3.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
a TRRS headphone jack for stereo out and composite out, a microphone,
an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
and a 40-pin GPIO header.
The added dts file is identical to the one submitted to the upstream
kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Dserve DSRV9703C is a 9.7" A10 tablet with a 1024x768 ips LCD,
1G RAM, 4GB flash, a Focaltech FT5406EE8 touchscreen and rtl8188ctv wifi.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The yones toptech bs1078-v2 is a 10.1" tablet without any clear markings on
the outside, but 'YONESTOPTECH-BS1078' written on the PCB silkscreen.
It features a 16:9 1024:600 LCD, A31s SoC, 1GB RAM, 8G NAND, silead gsl3675
touchscreen and a RTL8723AS wifi chip:
https://linux-sunxi.org/Yones_Toptech_BS1078_V2
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Sinlinx A31s SDK is a A31s based module/baseboard development kit.
The core module has the SoC, PMIC, DRAM, eMMC and supporting components.
There are also pads for UART0, JTAG and I2S.
The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0
hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume
buttons, RS232 style UART and USB OTG (though VBUS is not connected).
Various headers are available for other addon modules, such as SDIO
WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add defconfig for the multi board device based on the
Allwinner A20 SoC. It contains the A20 Itead Core module and a
base board for the external interfaces.
The core module comes with 4GB NAND and 1GB DDR RAM.
The base board to which the core board is connected provides
3 USB 2.0 Host ports, 1 USB 2.0 OTG, 1 uSD slot, 10/100 Ethernet
port, HDMI, IR receiver, SPDIF and a 32-pin GPIO header. This
header expands the features of core board by exposing the VGA pins,
audio In/Out pins, SATA, SPI, I2C, UARTS, USB-OTG and power..
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cubietruck Plus is a A83T/H8 based development board. The board has
standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host
via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet,
WiFi, headphone out / mic in, and various GPIO headers.
The board also has an EEPROM on i2c0 which holds the MAC address.
DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20
is connected to the reset control of the PHY. EMAC is not actually
supported yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Polaroid MID2809PXE4 is a 9" tablet which is clearly marked
Polaroid MID2809PXE4 on the back. It features a 9" 16:9 800x480 LCD,
A23 Soc, 1GB RAM, 8GB NAND, gsl3670 touchscreen and esp8089 wifi.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Difrnce dit4350 tablet is a tiny tablet with a 4.3" 16:9 480x272 LCD,
A13 SoC, 512M RAM, 4G NAND, solomon systech ssd2532qn6 touchscreen at
i2c1 address 0x48, Memsic MXC622X accelerometer at i2c1 address 0x15 and
rtl8188etv wifi.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The colorfly e708 q1 is a 7" tablet which is clearly marked as colorfly
e708 q1 on the back. It features a 9:16 800x1280 IPS LCD, A31s SoC,
1GB RAM, 8G NAND, ilitek 2139qt004 touchscreen on i2c-1 addr 0x41,
stk8313 accelerometer on i2c-2 addr 0x22 and a rtl8188etv wifi chip.
The added dts is identical to the dts submitted to the upstream kernel,
note this commit also syncs axp22x.dtsi and sun6i-a31.dtsi with the
upstream kernel as the added dts depends on these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is a device number, and we want to use 'dev' to mean a driver model
device. Rename the member.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.
This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Previously, AXP818 ALDO support was partially added to Kconfig, but
never enabled in the board file, nor properly set or configured in
Kconfig. The boards continue to work because the AXP818 is designed
to pair with the A83T/H8, and the default voltages match the reference
design's requirements.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Instead of one function for each DLDO regulator, make 1 function that
takes an extra "index". Since the control bits for the DLDO regulators
are contiguous, this makes the function very simple. This removes a lot
of duplicate code.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add dts and defconfig for Banana-pi M3 board.
It has 2G LPDDR3, UART, ethernet, USB, HDMI, USB Sata, MIPI DSI,
mic, AP6212 Wifi, etc on it.
It is paired with AXP813 PMIC which is almost same as AXP818.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com: rename to Sinovoip_BPI_M3_defconfig/sun8i-a83t-sinovoip-bpi-m3.dts]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Different A83T boards have different DRAM types. Banapi M3 has LPDDR3,
Allwinner Homlet v1.2 has DDR3.
This adds groundwork to support for new DRAM type for A83T.
Introduce CONFIG_DRAM_TYPE, It'll be 3 for DDR3 and 7 for LPDDR3, must
be set in respective board defconfig.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we support PSCI and various security switches, we can let
U-boot boot Linux into non-secure and HYP mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Heiko Schocher <hs@denx.de>
The Empire Electronix D709 tablet is a fairly standard 7" A13 tablet,
featuring usb-wifi, a micro-sd slot, micro-usb otg and headphone jack.
Empire Electronix is written on the back of the tablet, the D709 model
info can be found in the about tablet menu in android.
The PCB has no markings to speak of.
This dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add dts and defconfig for h8homletv2 board.
H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner.
It has UART, ethernet, USB, HDMI, etc ports on it.
A83T patches are tested on this board.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Enabled support for AXP818 in SPL and u-boot.
DCDC1, DCDC2, DCDC3 and DCSC5 are enabled.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Allwinner A83T is octa-core cortex-a7 SOC.
This enables support for A83T.
SMP is not yet supported.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.
The dts file is identical to the one submitted upstream.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Based on existing A23/A33 code and the original H3 boot0.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add initial sun8i H3 support, only uart + mmc are supported for now.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of
RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack
and two connectors to plug additional boards on top of it.
The DT is identical to the DT submitted to the upstream kernel.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Not all sunxi boards have an MMC embedded. Switching to the Kconfig option
will allow to enable or disable the support in each boards' defconfig.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features
1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
The dts changes are identical to the dts files submitted upstream.
A few notes on the use if dldo and aldo regulators. DLDO1 is used
for Vdd for the ethernet phy, ALDO2 is used for AVdd for the ethernet
phy. ALDO1 is used to power the sdio wifi module.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simplifying the callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On boards with axp221/223 pmic-s we already allow configuring most
voltages. Make the Kconfig options for these also apply to boards with
axp152 / axp209 pmic-s and extend them to configure all voltages.
The Kconfig defaults are chosen so that this commit does not introduce any
functional changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We now have generic q8_a?3_defconfig files for Q8 formfactor tablets with
an A13 / A23 / A33 SoC, there is no need for these PCB variant specific
defconfig-s and they only serve to confuse the user.
Note that in case of the forfun_q88db_defconfig and TZX-Q8-713B7_defconfig
for A13 based Q8 tablets there is not even a dts file for these in the
upstream kernel, which is all the more reason to remove them.
The generic q8_a?3_defconfig files have been tested on an Et_q8_v1_6,
Ippo_q8h_v1_2_a33_1024x600, Ippo_q8h_v1_2 and TZX-Q8-713B7 tablet, and the
forfun_q88db_defconfig is identical to q8_a13_tablet_defconfig.
This leaves only the Ippo_q8h_v5 untested with the new generic defconfigs
but there is no reason to assume that it will not work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Select CONFIG_SPL_STACK_R for sunxi boards, this gives us much more
room on the stack once we've the DRAM running.
Besides being a good change to have on itself, this also paves the
way for switching to using malloc_simple in the SPL which cuts of
close to 4KiB of the SPL size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The 7" Q8 tablet enclosure is used for a ton of slightly different cheap
chinese tablets. There are some differences in which accelerometer /
wifi is used, but other then that these are all the same from a u-boot /
kernel pov.
When we get to adding accelerometer support the plan is to add some kind
of autodetection and mangle the dt accordingly (likely using the new quirks
mechanism).
For now this is a non issue as we do not yet have accelerometer
support, and in the future, some sort of auto-detect is the way to go
as we cannot expect users to exactly know what is inside their tablet.
The dts files this commit adds are identical to the ones submitted
to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The 7" Q8 tablet enclosure is used for a ton of slightly different cheap
chinese tablets. There are some differences in which accelerometer /
wifi is used, but other then that these are all the same from a u-boot /
kernel pov.
When we get to adding accelerometer support the plan is to add some kind
of autodetection and mangle the dt accordingly (likely using the new quirks
mechanism).
For now this is a non issue as we do not yet have accelerometer
support, and in the future, some sort of auto-detect is the way to go
as we cannot expect users to exactly know what is inside their tablet.
The dts[i] files this commit adds are identical to the ones submitted
to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch extends the misc_init_r() function on sunxi boards
to test for the presence of a suitable "sunxi" SPL header. If
found, and the loader ("fel" utility) provided a non-zero value
for the boot.scr address, then the corresponding environment
variable fel_scriptaddr gets set.
misc_init_r() also sets (or clears) the "fel_booted" variable depending
on the active boot device, using the same logic as spl_boot_device().
The goal is to provide sufficient information (within the U-Boot
environment) to make intelligent decisions on how to continue the boot
process, allowing specific customizations for the "FEL boot" case.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We only prefix the board defconfig name with the SoC if the SoC is part
of the official board-name, such as with Olimex OLinuxIno boards, for the
Wobo i5 this is not the case so remove the A10s prefix from the defconfig
filename.
Also fix the double listing of A10s-OLinuXino-M_defconfig in MAINTAINERS
which the original Wobo i5 addition commit introduced.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Wobo i5 top set box is a somewhat curious A10s based top set box,
it uses an AXP209 rather then the AXP152 usually used in combination
with the A10s. It has an ethernet phy connected to PORTD rather then
PORTA, and its built-in usb wifi is connected via the otg controller.
The dts file changes are identical to the changes submitted to the
upstream kernel.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This commits adds a generic support for q8 formfactor a13 based tablets.
These tablets ship in many variants, with the difference mainly being the
touchscreen controller / accelerometer / wifi chip used.
The wifi is USB based, and thus not listed in devicetree.
ATM the kernel does not support the touchscreen / accelerometer on these
devices. In the future we may need multiple configs with different
CONFIG_DEFAULT_DEVICE_TREE settings, this depends on how we solve the
hw differences on the kernel side.
For now this will suffice.
The dts files are identical to the dts files submitted to the upstream
kernel for these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The iNet-tek iNet-1 PCB is a PCB found in various generic 10.1" 1024x600
A10 based tablets such as the Point of View Protab2 XXL and the
Cherry M1007.
This patch has been tested on both rev2 and rev5 of this board / these
tablets.
These tablets feature the usual connectors: headphone, mini hdmi,
power-barrel, mini-usb and a micro-sd slot.
The dts is identical to the dts submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The inet9f-rev03 pcb is specially designed for gaming tablets, such as
the qware tb-g100 tablet.
These 7" tablets feature a dpad, firebuttons and 2 joysticks on the sides
of the screen.
Besides this they have the usual connectors: power-barrel, mini usb,
mini hdmi, headphone and micro-sd slot.
The dts is identical to the dts submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Point of View protab2-ips9 is a tablet with a 9" ips 1024x768 lcd
screen, microsd slot, headphones, mini hdmi, mini usb b and power barrel
connectors.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The boards are sorted by SoC, move the Mele_A1000G_quad entry to the list
of sun6i boards where it belongs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The inet98v_rev2 is a pcb used in generic A13 based tablets. It features
volume buttons, a power barrel, micro-usb otg, headphone connector and
a power button.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The inet97fv2 is a board found in the first generation of cheap allwinner
A10 based 7" tablets.
Note that this patch does not add a dts file as we already have one from
our dts syncs with the kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We eventually want to add full nand support, since it makes no sense
to build SPL with nand support and u-boot without, or the other way
around, a single option will suffice.
Renaming the Kconfig option now makes things easier when we add full
nand support in the future.
The "obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o" is moved to an
"ifdef CONFIG_SPL_BUILD" block in the Makefile.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Other then having a few less chip-select lines the nand controller
on sun4i, sun5i and sun7i is identical.
Note this patch also muxes GPC7 to the NAND on sun7i where as before
it was not muxed this way. GPC7 is a standard NAND pin, so it should
always be muxed to the NAND when in use.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We use DMA for nand data transfers in the SPL, so make sure the DMA
controller is enabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Use SYS_NAND_SELF_INIT and only setup the pinmux and clocks when we are
actually using the nand.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
With the unified / cleaned up default display output selection changes,
which were done as part of adding composite video out support, our
example LCD_MODE line in the A13-OLinuxIno defconfigs causes the display
code to setup a LCD console by default, rather then a VGA console.
Given that the LCD console is only useful for people who have hooked up
the exact lcd-panel from the config, while most people will not have any
lcd panel connected to these boards, this is not a good default.
Dropping the LCD_MODE line which was intended as an example fixes this,
instead add a link to the LCD_MODE help text pointing to
http://linux-sunxi.org/LCD which contains the removed and other example
modes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The gt90h is a pcb found in generic 9" tablets with an A23 soc, 1G RAM
and 8G nand, rtl8723as usb wifi, 1 micro usb port and 1 micro sd slot.
The pmic setup on this board is somewhat special, dcdc2 MUST be set
to 1.1V instead of the usual 1.2V otherwise the board is very unstable.
aldo1 is used to power the micro sd slot, dldo1 is used for wifi.
This commit adds a defconfig + dts (as submitted to the kernel) for
the gt90h-v4 pcb.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Allow specifying the axp221 dcdc2 voltage via Kconfig, this is necessary
because on some boards the 1.2V default does not work reliable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for 4 1.62G lane eDP panels connected via an anx9804 bridge,
such as found on the Colombus devkit.
While at it also fix the wrong indentation of the SSD2828 Kconfig help text
in board/sunxi/Kconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Auxtek-T003 HDMI stick is an A10s based HDMI stick with USB wifi,
and composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add composite video out support.
This only gets enabled on the Mele M3 for now, since that is were it
was tested. It will be enabled on more boards after testing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
To enable NAND flash in sunxi SPL,
pins 0-6, 8-22 and 24 on port C are configured.
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
