Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Multiple boards create duplicate entries in their respective
-u-boot.dtsi files which all basically do the same thing.
To consolidate these and make it easier to make improvements
going forward, consolidate them all into one place.
This file creates a flash.bin image using binman, and supports
LPDDR4, DDR4 and DDR3. Since individual boards use different
peripherals and different UART ports, those entries were kept
in their respective board files, but the spba1 node was addded
which contains all UART1-3 to help facilitate SPL_DM_SERIAL.
Individual users will still need to include their respective
UART and pinctrl nodes for those UARTS.
This consolidated file also supports generating a flash.bin file
which can boot from flexSPI if CONFIG_FSPI_CONF_HEADER is
enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Commit 290ffe5788 (imx8m: fix reading of DDR4 MR registers) lifted a
private definition of lpddr4_mr_read() from imx8mm-cl-iot-gate board
code to drivers/ddr/imx/imx8m/ddrphy_utils.c, because that version
actually seems to work in practice.
However, commit 99c7cc58e1 (ddr: imx: Add i.MX9 DDR controller driver)
reintroduced the broken version in drivers/ddr/imx/imx8m/ddr_init.c,
copied most of the rest of ddrphy_utils.c to
drivers/ddr/imx/phy/ddrphy_utils.c, and stopped building
drivers/ddr/imx/imx8m/ddrphy_utils.c [and that file was then finally
completely removed with 7e9bd84883 (imx8m: ddrphy_utils: Remove unused
file)].
I assume this must have broken the imx8mm-cl-iot-gate board, at least
those that have not had their eeprom programmed with the proper
information. It certainly did break our out-of-tree board which always
reads back the ID register and uses that for a sanity check.
So apply the fix from 290ffe5788 once again.
Fixes: 99c7cc58e1 (ddr: imx: Add i.MX9 DDR controller driver)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <festevam@denx.de>
- enable bootcount command
- integrate bootcount using SNVS_LP general purpose register LPGPR0
- enable link-time optimisation
- explicitly set a boot delay of one second
- enable CRC32 and MD5
- enable command for low-level access to data in a partition
- enable time commands
- enable PMIC commands
- improve ETHPRIME configuration
- enable eMMC HS400 functionality
- enable fixed PHY and MDIO driver model
- remove stale PFUZE100 PMIC driver
- enable thermal management unit driver
- enable more USB host functionality
- enable hexdump
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Update the distro config env memory layout for the Verdin iMX8M Mini and
Verdin iMX8M Plus again:
- loadaddr=0x48200000 allows for 128MB area for uncompressing (ie FIT
images, kernel_comp_addr_r, kernel_comp_size)
- fdt_addr_r = loadaddr + 128MB - allows for 128MB kernel
- scriptaddr = fdt_addr_r + 512KB - allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB - allows for 512KB script
Memory layout taken from commit fd5c7173ad
("imx8m{m,n}_venice: update env memory layout").
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Note that this corrects a pre-maturely applied version 2 of the same
patch set.
Fixes: bbe0089d29 ("verdin-imx8mm: verdin-imx8mp: update env memory layout")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW7904 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD connector with UHS support
- LIS2DE12 3-axis accelerometer
- Gateworks System Controller
- IMX8M FEC
- 2x RS232 off-board connectors
- PMIC
- 10x bi-color LED's
- 1x miniPCIe socket with PCIe and USB2.0
- 802.3at Class 4 PoE
- 10-30VDC input via barrel-jack
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Plus PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Sync the i.Core MX8M Plus is an EDIMM SoM based on NXP
devicetree file from linux-next tree.
commit <aec8ad34f7f24> (arm64: dts: imx8mp: Add Engicam i.Core MX8M Plus EDIMM2.2 Starter Kit)
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus
from Engicam.
General features:
- NXP i.MX8M Plus
- Up to 4GB LDDR4
- 8 eMMC
- Gigabit Ethernet
- USB 3.0, 2.0 Host/OTG
- PCIe 3.0 interface
- I2S
- LVDS
- rest of i.MX8M Plus features
i.Core MX8M Plus needs to mount on top of Engicam baseboards
for creating complete platform solutions.
Add support for it.
Sync the i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus
from Engicam devicetree file from linux-next tree.
commit <eefe06b295087> (arm64: dts: imx8mp: Add Engicam i.Core MX8M Plus SoM)
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The GW7903 has a BD71847 PMIC on I2C1. Adjust the model compare strings
to add it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Fix the MMC env device for boards with eMMC by adding a
board_mmc_get_env_dev override to return the boot device as the
MMC env device.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
With sf update fixed to support unaligned start offset, use plain
sf update to update the bootloader in SPI NOR. This also helps
avoid the case where not enough SPI NOR has been erased and the
bootloader has been written to unerased area, and thus corrupted.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The btrfs filesystem provides advanced functionality like copy-on-write
and snapshots, as well as metadata and data duplication and checksumming.
Enable btrfs in U-Boot to permit even the primary partition to be btrfs
and let system boot from it.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
issue:
CAAM fails with key error when perform Modular Exponentiation
using PKHA Block in CAAM
Fix:
add flush and invalidate dcache for keys, signature
and output decrypted data processed by CAAM.
Fixes: 34276478f7 (DM: crypto/fsl - Add Freescale rsa DM driver)
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Update the distro config env memory layout for the Apalis iMX6,
Colibri iMX6, Colibri iMX6ULL and Colibri iMX7:
- loadaddr=0x84200000 (resp. 0x14200000 on them i.MX 6) allows for 64MB
area for uncompressing (ie FIT images)
- fdt_addr_r = loadaddr + 64MB : allows for 64MB kernel
- scriptaddr = fdt_addr_r + 512KB : allows for 512KB fdt
- pxefile_addr_r = scriptaddr + 512KB : allows for 512KB script
- ramdisk_addr_r = pxefile_addr_r + 512KB : allows for 1MB extlinux.conf
Memory layout analogous to 64-bit one from commit fd5c7173ad
("imx8m{m,n}_venice: update env memory layout") but left pxefile_addr_r
updated according to doc/develop/distro.rst.
This fixes a potential issue caused by the compressed kernel being
relocated on top of the ramdisk causing its corruption.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
After commit 395110284b ("nitrogen6x: Populate FDTFILE at build-time
for all platforms") iMX.6Q Sabrelite fails to boot due to a bad fdtfile
string:
Retrieving file: /dtbs/5.18.0-0.deb11.4-armmp/"imx6q-sabrelite".dtb
** File not found /dtbs/5.18.0-0.deb11.4-armmp/"imx6q-sabrelite".dtb **
CONFIG_DEFAULT_DEVICE_TREE option is string typed, so __stringify() is
adding extra quotes. Remove this.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
The QSPI clocks are only used when CONFIG_NXP_FSPI=y, so only build the
QSPI clocks in this case to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The ecspi clocks are only used when CONFIG_DM_SPI=y, so only build the
ecspi clocks in this case to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Ethernet is not used inside SPL, so move the IMX8MM_CLK_ENET_AXI clock
inside the non-SPL block to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
PWM is not used inside SPL, so do not define the PWM clocks inside
SPL to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Move init_clk_usdhc to non-clk driver case, since assigned-clocks properties
will initialize the clocks by clk driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
... to avoid loosing characters when pasting text into the serial console.
This allows to remove the workaround to disable the vidconsole output
when no HDMI device is detected. This workaround only was there to speed-up
serial console processing.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add Serial Download Protocol support as it is a useful method to
load flash.bin to RAM and run it via 'uuu'.
With this patch, it is possible to start both U-Boot SPL and U-Boot
proper using the following 'uuu'command:
$ uuu -brun spl flash.bin
Based on a patch from Marek Vasut for the imx8mm-mx8menlo board.
Also, to fit the SPL binary into the internal RAM, select CONFIG_LTO
to reduce its size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add an entry for USB boot so that U-Boot could be loaded via
the Serial Download Protocol.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Enable DM USB, DM PHY and USB gadget support in imx8mm-mx8menlo SPL
to let the board continue SDP loading of second stage after the first
stage was loaded by BootROM SDP implementation. It is not possible to
jump back into BootROM v1 and let the BootROM implementation continue
the SDP loading, all this has to be performed by the U-Boot CI HDRC
controller driver and SDP protocol implementation, both of which fit
into the SPL just barely.
With this patch, it is possible to start both U-Boot SPL and U-Boot
using e.g. uuu on this board as follows:
$ uuu -brun spl flash.bin
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The current implementation of spl_board_init() USB boot handling is
not correct, the MX8MM BootROM v1 does not support SDP load when
re-entered from U-Boot SPL, it is up to U-Boot to perform the next
stage load using its own internal CI gadget driver and SDP protocol
implementation. Drop the spl_board_init() to let SPL continue with
normal load in case the SDP support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The current implementation of spl_board_init() is not correct,
the MX8MM BootROM v1 does not support SDP load when re-entered
from U-Boot SPL, it is up to U-Boot to perform the next stage
load using its own internal CI gadget driver and SDP protocol
implementation. Drop the spl_board_init() to let SPL continue
with normal load in case the SDP support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Instead of duplicating code implemented by i.MX8M version of arch_misc_init()
in every board, enable CONFIG_ARCH_MISC_INIT and call arch_misc_init() from
spl_board_init(). This removes the duplication. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The first production revision of the MX8M Mini Menlo board implements
a hardware change which swaps console UART and another UART connector.
Implement the swap, which maps the console UART back to the way Verdin
console is mapped.
Signed-off-by: Marek Vasut <marex@denx.de>
The GW7903 revision B adds two additional GPIO's to control the
direction of the 2 isolated digital I/O circuits.
Define them as:
- dig1_ctl
- dig2_ctl
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Update the GW74xx PMIC configuration:
- increase VDD_SOC DVS1 to 0.85V per datasheet
- increase VDD_SOC DVS0 to 0.95V before first DRAM access
- increase VDD_ARM DVS0 to 0.95V to support kernel overdrive voltage (OD)
- remove unnecessary changes to VDD_DRAM as we don't use 3GHz DRAM
- remove unnecessary change to LDO2 as it is unused
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
v2: update commit log with more detail
Update the M2 socket gpio hogs such that they are not active on boot by
flagging them as GPIO_ACTIVE_HIGH so that 'output-high' drives high.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Update the UART config gpio hogs such that it is configured for RS232
by default on boot. Additionally rename them to match the names used
on the reset of the venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add RAM auto-sizing, without this change memory size for all SKU is set
to 8GB and the system will crash on SKU with less memory as soon as the
non existent memory addresses are accessed.
Fixes: 2bc2f817ce ("board: toradex: add verdin imx8m plus support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
With this call the following attributes get set to the device-tree
and are then accessible from linux in /proc/device-tree/
serial-number: The serial number that is stored in config-block
toradex,board-rev: The version of the module (e.g. V1.1A)
toradex,product-id: The SKU number of the module runnin
Fixes: commit 2bc2f817ce ("board: toradex: add verdin imx8m plus support")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
With this call the following attributes get set to the device-tree
and are then accessible from linux in /proc/device-tree/
serial-number: The serial number that is stored in config-block
toradex,board-rev: The version of the module (e.g. V1.1A)
toradex,product-id: The SKU number of the module running
Fixes: commit 14d5aeff77 ("board: toradex: Add Verdin iMX8M Mini support")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Enable the I2C bus and set a env variable for the reset GPIO of the touch
controller. This allows us to probe the panel in a script.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This adds support for the Kontron Electronics SoM SL i.MX8MM OSM-S
and the matching baseboard BL i.MX8MM OSM-S.
The SoM hardware complies to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).
The existing board configuration for the non-OSM SoM is reused and
allows to detect the SoM variant at runtime.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Refactor the code a bit without any functional changes.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Improve the naming of the regulators to contain the voltage rail
names from the schematic.
Suggested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
