Because CONFIG_MMU is never defined in U-Boot,
the non-MMU code in debug.S is always used.
Unfortunately, the number of arguments of the addruart macro
in Linux is different between MMU and non-MMU.
This causes a build error when importing some debug macros
using the third argument. (For ex. arch/arm/include/debug/exynos.S)
Pass the third argument to the non-MMU addruart to avoid such a problem.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
We have not had a good method to debug the early boot stage such as
lowlevel_init function. I guess developers generally use dedicated
debuggers for that, but it is difficult in some cases.
(For example, my debugger cannot connect to the ARM processor when
it is in the secure state. It sometimes happens when I need to
debug the early boot stage on ARM SoCs with secure extension.)
The low level debug feature in Linux would be also helpful for U-boot
when we are stucking in nasty problems where the console is not
available yet.
You have to enable CONFIG_DEBUG_LL to use this feature.
For now, only 8250-compatible UART devices are supported.
You can add a header file under arch/arm/include/debug/ directory
to support your UART device if necessary.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
U-Boot does not have arch/arm/kernel, include/uapi directories,
This commit copies files as follows:
Location in Linux -> Location in U-Boot
arch/arm/kernel/debug.S -> arch/arm/lib/debug.S
arch/arm/include/debug/8250.S -> arch/arm/include/debug/8250.S
include/uapi/linux/serial_reg.h -> include/linux/serial_reg.h
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since the environment "VENDOR" is set in tcsh, it must be cleared in our
makefile. Otherwise, boards without CONFIG_SYS_VENDOR fail to build:
> make CROSS_COMPILE=arm-linux-gnueabi- wandboard_quad_defconfig all
[ snip ]
AR arch/arm/lib/lib.a
CC arch/arm/lib/eabi_compat.o
scripts/Makefile.build:55: /home/foo/u-boot/board/unknown/wandboard/ \
Makefile: No such file or directory
make[2]: *** No rule to make target `/home/foo/u-boot/board/unknown/ \
wandboard/Makefile'. Stop.
make[1]: *** [board/unknown/wandboard] Error 2
make: *** [__build_one_by_one] Error 2
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reported-by: Tom Everett <tom@khubla.com>
Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Without the private libgcc, we need a full multilib toolchain with
different libgcc or multiple toolchains to build all BE/LE and
hard-float/soft-float variants of MIPS boards. That is not feasible.
This commit allows us to build all the MIPS boards with a single
kernel.org toolchain:
https://www.kernel.org/pub/tools/crosstool/files/bin/x86_64/4.9.0/
x86_64-gcc-4.9.0-nolibc_mips-linux.tar.xz
This change sounds reasonable for most users. If necessary,
you can disable this option via "make menuconfig" or friends.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When spl/.config is updated by "make spl/menuconfig" or friends,
spl/include/config/auto.conf, spl/include/generated/autoconf.h
and some other files must be updated by "make silentoldconfig".
There is no hook for SPL in the top Makefile, so this commit
touches .config when spl/.config is updated to invoke silentoldconfig.
Likewise for TPL.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
cmd_u-boot-spl includes $(PLATFORM_LIBS) which changes
when CONFIG_USE_PRIVATE_GCC is updated. The u-boot-spl image
should be re-linked if any prerequisite is newer than it
or the command line has changed.
$(call, if_changed,...) should be used instead of $(call cmd,...).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The private libgcc is supported only on ARM, MIPS, PowerPC, SH, x86.
Those architectures should "select" HAVE_PRIVATE_LIBGCC and
CONFIG_USE_PRIVATE_LIBGCC should depend on it.
Currently, this option is enabled on Tegra boards and x86 architecture.
Move the definition from header files to Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Now CONFIG_USE_PRIVATE_LIBGCC is only used as a boolean macro.
Remove CONFIG_USE_PRIVATE_LIBGCC=path/to/libgcc syntax.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
The motivation of this commit is to change CONFIG_USE_PRIVATE_LIBGCC
to a boolean macro so we can move it to Kconfig.
In the current implementation, there are two forms of syntax
for this macro:
- CONFIG_USE_PRIVATE_LIBGCC=y
- CONFIG_USE_PRIVATE_LIBGCC=path/to/private/libgcc
The latter is only used by x86 architecture.
With a little bit refactoring, it can be converted to the former.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_SYS_HZ is always defined as 1000 in config_fallbacks.h
(but some boards still have redundant definitions).
This commit moves the definition and the document in README to
Kconfig. Since lib/Kconfig can assure that CONFIG_SYS_HZ is 1000,
the sanity check in lib/time.c should be removed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add target to build it automatically upon "make" / MAKEALL. This can/should
be set by board / cpu specific headers if a special U-Boot image is
required for this SoC / board.
E.g. used by Marvell Armada XP to automatically build the u-boot.kwb
target.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
This patch integrates the Barebox version of this kwbimage.c file into
U-Boot. As this version supports the image version 1 type for the
Armada XP / 370 SoCs.
It was easier to integrate the existing and known to be working Barebox
source than to update the current U-Boot version to support this
v1 image header format. Now all Marvell MVEBU SoCs are supported:
Image type 0: Kirkwood & Dove
Image type 1: Armada 370 & Armada XP
Please note that the current v1 support has this restuction (same as
has Barebox version):
Not implemented: support for the register headers and secure headers
in v1 images
Tested on Marvell DB-78460-BP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
The barebox version of the kwboot tool has evolved a bit. To support
Armada XP and Dove. Additionally a few minor fixes have been applied.
So lets sync with the latest barebox version.
Please note that the main difference between both versions now is, that
the U-Boot version still supports the -p option, to dynamically patch
an image for UART boot mode. I didn't test it now though.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
The maxBCM board is equipped with the Marvell Armada-XP MV78460 SoC. It
integrates an SPI NOR flash and an Marvell 88E6185 switch.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic support for the Marvell DB-MV784MP-GP evaulation
board. This is the first board that uses the recently created
Armada XP 78460 SoC support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
This basic support for the Marvell Armada XP is base on the existing kirkwood
support. Which has been generatized by moving some common files into
common marvell locations.
This is in preparation for the upcoming Armada XP MV78460 support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
To support the Armada XP SoC, we just need to include the correct header.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
The Marvell MV78460 eval board DB-78460-BP seems to need a longer
PHY autonegotiation timeout than the "standard" 4 seconds. So lets
make this timeout configurable. If not defined in the board config
header the original 4000ms is used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
This patch adds support for the NETA ethernet controller which is integrated
in the Marvell Armada XP SoC's. This port is based on the Linux driver which
has been stripped of the in U-Boot unused portions.
Tested on the Marvell MV78460 eval board db-78460-bp.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
Additionally the SDRAM address decoding register address is not hard coded
in the C code any more. A define is introduced for this base address.
This makes is possible to use those gpio functions from other MVEBU SoC's
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This makes is possible to use this SPI driver from other MVEBU SoC's as well.
As the upcoming Armada XP support will do.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This makes is possible to use those gpio functions from other MVEBU SoC's as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Compile the pin multiplexing only on Kirkwood platforms. As the
Armada XP doesn't need it.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
These mbus functions are ported from Barebox. The Barebox version is
ported from Linux. These functions will be first used by the upcoming
Armada XP support. Later other Marvell SoC's will be adopted to use
these functions as well (Kirkwood, Orion).
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
This patch does the following:
- Rename defines and registers to not use kirkwood
- Remove unused defines
- Use clrsetbits() accessor functions
- Coding style cleanup
- Clear 25MHZ bit in timer controller register init for Armada XP
There is no functional change for kirkwood. At least not intentionally.
This will be used by the upcoming Armada XP support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This move makes it possible to use this kirkwood SPI driver from other
MVEBU platforms as well. This will be used by the upcoming Armada XP
support.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
By moving some kirkwood files into a Marvell common directory, those files
can be used by other Marvell platforms as well. The name mvebu is taken
from the Linux kernel source tree. It has been chosen there to represent
the SoC's from the Marvell EBU (Engineering Business Unit). Those SoC's
currently are:
Armada 370/375/XP, Dove, mv78xx0, Kirkwood, Orion5x
This will be used by the upcoming Armada XP (MV78460) platform support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Enable FIT support and the bootelf command. Also change the default load
address to somewhere other than the normal load address of the kernel,
to allow for decompression without overwriting the original file.
Signed-off-by: Simon Glass <sjg@chromium.org>
To get a display in U-Boot on link you must either build a coreboot that
always sets it up, or use Esc-Refresh-Power to reset the machine.
When we do have a display, it is nice to display the model at the top, so
enable this option.
Signed-off-by: Simon Glass <sjg@chromium.org>
We may as well use hush. The auto-complete option was incorrect so this was
not enabled. Also expand the command line size a little and go back to the
default prompt since "boot>" doesn't seem any more useful.
Signed-off-by: Simon Glass <sjg@chromium.org>
The fdt_for_each_subnode() iterator macro provided by this patch can be
used to iterate over a device tree node's subnodes. At each iteration a
loop variable will be set to the next subnode.
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The fdtdec_pci_get_bdf() function returns the bus, device, function
triplet of a PCI device by parsing the "reg" property according to the
PCI device tree binding.
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the fdt_get_resource() and fdt_get_named_resource() functions which
can be used to parse resources (memory regions) from an FDT. A helper to
compute the size of a region is also provided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Given a device tree node, a property name and an index, the new function
fdt_get_string_index() will return in an output argument a pointer to
the index'th string in the property's value.
The fdt_get_string() is a shortcut for the above with the index being 0.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
