Canyonlands (460EX) shares the first PCIe interface with the SoC SATA
interface. This usage can be configured with the jumper J6. This patch
correctly configures the SATA/PCIe PHY for SATA usage when this jumper
is installed.
Signed-off-by: Stefan Roese <sr@denx.de>
This board never went into production
Signed-off-by: Zachary P. Landau <zachary.landau@labxtechnologies.com>
Acked-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>
Add support for the ptm1la, ptm1ms, ptm2la and ptm2ms
environment variables.
Cleanup pci_target_init.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
All of the duplicated code for Blackfin processors and boot modes have been
unified. After all, the core is the same for all processors, just the
peripheral set differs (which gets handled in the drivers).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This punts the old spi flash driver for a new/generalized one until the
common one can be integrated.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This fixes a naming bug for at91rm9200 lowlevel init code:
NOR boot flash is on chipselect 0, not chipselect 2. This
makes code use the register name from chip datasheets.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by Freescale.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the Phytec Phycore-i.MX31 board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the mx31 litekit board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch fixes eeprom page size so that you can now write more than
64 bytes at a time.
It also makes the board take MAC addresses, if found, from EEPROM.
User should place up to 4 addresses at offset 0x7f00, for
eth{,1,2,3}addr. Any unused addresses should be zero. This group of
four six-byte values should have it's CRC at the end. crc32 and
eeprom commands can be used to accomplish this.
If CRC fails, MAC addresses come from the environment. If CRC
succeeds, the environment is overwritten at startup.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
in the spirit of commit 1ced121600,
85xx's "Update SVR numbers to expand support", simplify SPRIDR processing
and processor ID display. Add REVID_{MAJ,MIN}OR macros to make
REVID dependent code simpler. Also added PARTID_NO_E and IS_E_PROCESSOR
convenience macros.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch is stolen from Anton Vorontsov's patch
for mpc837xerdb boards.
The reference clk and xcorevdd voltage of serdes1/2
is same between mpc837xemds and mpc837xerdb.
8377E: LYNX1- 2 SATA LYNX2- 2 PCIE
8378E: LYNX1- 2 SGMII LYNX2- 2 PCIE
8379E: LYNX1- 2 SATA LYNX2- 2 SATA
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Canyonlands (460EX) shares the first PCIe interface with the SoC SATA
interface. This usage can be configured with the jumper J6. This patch
displays the current configuration upon bootup and changes the PCIe
init loop, to only initialize the availabel PCIe slots.
Signed-off-by: Stefan Roese <sr@denx.de>
R2D plus is SH reference board used with SH7751R.
This board has 266Mhz CPU, 64MB SDRAM, Cardbus, CF interface,
one PCI bus, VGA, and two Ethernet controller.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Renesas Solutions R7780MP is a reference board on SH7780.
This board has serial, 10/100 base Ethernet deivice, CF slot
and VGA devices. This board can set extension board.
Extension board has 10/100/1000 base Ethernet device, PCI slot,
S-ATA, iDVR slot.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Migo-R is a board based on SH7722 and has may devices.
In this patch, supported SCIF, NOR flash and Ethernet.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since all ECC related problems seem to be resolved on LWMON5, this patch
now enables ECC support.
We have to write the ECC bytes by zeroing and flushing in smaller
steps, since the whole 256MByte takes too long for the external
watchdog.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch contains updates for changes for the Korat PPC440EPx board.
These changes include:
(1) Support for "permanent" and "upgradable" copies of U-Boot, as
described in the new "doc/README.korat" file;
(2) a new memory map for the registers in the board's CPLD;
(3) a revised format for manufacturer's data in serial EEPROM; and
(4) changes to track updates to U-Boot for the Sequoia board.
Signed-off-by: Larry Johnson <lrj@acm.org>
Since this board will probably be ported to arch/powerpc in the
near future, we add device tree support now. This way we are
"ready" for arch/powerpc from now on.
Signed-off-by: Stefan Roese <sr@denx.de>
The routine ft_board_setup() configures the EBC NOR mappings for the
Linux physmap_of driver. Since on 460EX/GT we remap the FLASH from
0x4.fc00.0000 to 0x4.cc00.0000 because of the max. 16MByte boot-CS
problem, we need to pass the corrected address here too.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Currently EMAC2+3 are not working. This will be fixed in a later
release.
Signed-off-by: Stefan Roese <sr@denx.de>
Each file that can be built here now follows some
CONFIG_ option so that they are appropriately built
or not, as needed. And CONFIG_ defines were added
to various board config files to make sure that happens.
The other board/freescale/*/Makefiles no longer need
to reach up and over into ../common to build their
individually needed files any more.
Boards that are CDS specific were renamed with cds_ prefix.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
