All other u-boot architectures have an include/asm/errno.h, so
this change adds it to the mips include/asm-mips headers also.
Stolen from Linux 2.6.25.
Signed-off-by: Jason McMullan <mcmullan@netapp.com>
The mips architecture currently does not call 'spi_init()' in the generic
board initialization routine is CONFIG_CMD_SPI is defined.
This patch rectifies that problem.
Signed-off-by: Jason McMullan <mcmullan@netapp.com>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
This patch adds the standard 'nand_init()' call to the mips generic
'board_init_r()' call, bringing MIPS in line with the other architectures.
Signed-off-by: Jason McMullan <mcmullan@netapp.com>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
The nand_info array is declared as extern in several .c files.
Those days, nand.h contains a reference to the array, so there is
no need to declare it elsewhere.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This allows the header to be included regardless of whether a board's
config file provides NAND-related defininitions.
Signed-off-by: Scott Wood <scottwood@freescale.com>
If the specified delay is very short, the cycle counter may go past the
"end" time we are waiting for before we get around to reading it.
Fix it by checking the different between the cycle count "now" and the
cycle count at the beginning. This will work as long as the delay
measured in number of cycles is below 2^31.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Remove #ifdef CONFIG_MMC from the source file and use conditional
compilation in the Makefile instead.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Make sure we check for CRC errors when sending commands that use CRC
checking.
Reported-by: Gururaja Hebbar K R <gururajakr@sanyo.co.in>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This cleans up the SDRAM initialization and related code a bit, and
allows faster booting.
* Add definitions for EBI and internal SRAM to asm/arch/memory-map.h
* Remove memory test from sdram_init() and make caller responsible
for verifying the SDRAM and determining its size.
* Remove base_address member from struct sdram_config (was sdram_info)
* Add data_bits member to struct sdram_config and kill CFG_SDRAM_16BIT
* Add support for a common STK1000 hack: 16MB SDRAM instead of 8.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Don't do a stack dump if the stack pointer is outside the memory area
reserved for stack.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Since the reset vector is always aligned to a very large boundary, we
can save a couple of KB worth of alignment padding by placing the
exception vectors at the same address.
Deciding which one it is is easy: If we're handling an exception, the
CPU is in Exception mode. If we're starting up after reset, the CPU is
in Supervisor mode. So this adds a very minimal overhead to the reset
path (only executed once) and the exception handling path (normally
never executed at all.)
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
All C code is compiled with -ffunction-sections -fdata-sections.
Assembly functions should get their own sections as well so that
everything looks consistent.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
pm_init() was always more about clock initialization than anything
else. Dealing with PLLs, clock gating and such is also inherently
SoC-specific, so move it into a SoC-specific directory.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Rework the HMATRIX configuration interface so that it becomes easier
to configure the HMATRIX for boards with special needs, and add new
parts.
The HMATRIX header file has been split into a general,
chip-independent part with register definitions, etc. and a
chip-specific part with SFR bitfield definitions and master/slave
identifiers.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This is a replacement for ATSTK1002 with 64MB SDRAM and NAND flash on
board. It's currently in production and will be available soon.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The .flashprog section was only needed back when we were running
directly from flash, and it's even more useless on NGW100 since it
uses the CFI flash driver which never used this workaround in the
first place.
Remove it on STK1000 as well, and get rid of all the associated code and
annotations.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
get_macb_pclk_rate() and get_macb_hclk_rate() should be available when
the chip has a MACB controller, not when it has a USART.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch forces the watchdog off in all cases. That will at least
get rid of the constant reboot cycle, though it won't let the watchdog
actually run in the new kernels: its probe() comes up with a polite
warning.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Make STK1002 and NGW100 boards act more alike:
- STK boards can use as many arguments as NGW
- STK boards don't need to manage FPGAs either
- NGW commands should match STK ones
Also spell U-Boot right in prompts for STK1002 and NGW100.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
[haavard.skinnemoen@atmel.com: update STK100[34] as well]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
In case of several PCI USB controllers on a board this variable
specifys which controller to use.
See doc/README.generic_usb_ohci for details.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Add new configuration variable CONFIG_PCI_OHCI_DEVNO.
In case of several PCI USB controllers on a board this variable
specifys which controller to use.
Also add USB support for sokrates board.
See doc/README.generic_usb_ohci for details.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Add DIU and cfb console support to FSL 5121ADS board.
Use #define CONFIG_VIDEO in config file to enable fb console.
Signed-off-by: York Sun <yorksun@freescale.com>
