- Import various DT files for DRA7 / DR72x / dra72-evm from Linux Kernel
v4.1
- Add config file for this board, enable DM and DM_GPIO
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The "method" parameter was part of the original port of the driver from
the kernel. At some point this may have been added to allow for future
differentiation (as omap1 and omap2 have different GPIO IP blocks, so
this wasn't an unreasonable thing to do). At this point however it's
just extra overhead, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable 8bit interface on HSMMC2 for am43xx to support 8bit eMMC chips.
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
The CMD(DAT) lines reset procedure described in the OMAP4(AM335x,
OMAP5, DRA7xx) TRMs is also necessary for AM43XX. Enable it in the
driver.
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add support for AM43XX to the omap3_spi driver.
Cc: Jagan Teki <jteki@openedev.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This patch adds the glue code for hi6220 SoC which has 2x synopsis
dw_mmc controllers. This will be used by the hikey board support
in subsequent patches.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a simple pmic driver for the hi6553 pmic which is used in
conjunction with the hi6220 SoC on the hikey board. Eventually this
driver will be updated to be a proper UCLASS PMIC driver which
can parse the voltages direct from device tree.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Remove the CONFIG_DM_USB limitation to enable cache support functions.
Tested on SAMA5D3x-EK board.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
gpio.h - Added missing copyright in few files.
rsa-mod-exp.h - Corrected copyright in the file.
fsl_sec.h - Added missing license in files
drivers/crypto/fsl/Makefile - Removed the incomplete GPLv2 license and replaced it with GPLv2+ license
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
The menuconfig for drivers are getting more and more cluttered
and unreadable because too many entries are displayed in a single
flat menu. Use hierarchic menu for each category.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Update to apply again in a few places, drop USB hunk]
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds dcache support for dwc2. The DMA buffers must be DMA aligned and
is flushed for outgoing transactions before starting transfer. For
ingoing transactions it is invalidated after the transfer has finished.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[trini: Update to apply again on top of DM patches]
Signed-off-by: Tom Rini <trini@konsulko.com>
The mailbox buffer is required to be at least 16 bytes aligned, but for
cache invalidation and/or flush it needs to be cacheline aligned.
Use ALLOC_CACHE_ALIGN_BUFFER for all mailbox buffer allocations.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
This allows scanning the twl4030 keypad, storing the result in a 64-byte long
matrix with the twl4030_keypad_scan function.
Detecting a key at a given column and row is made easier with the
twl4030_keypad_key function.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for detecting a few inputs exported by the TWL4030.
Currently-supported inputs are the power button, USB and charger presence.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This adds support for powering off (the omap3 SoC) from the twl4030. This is
especially useful when the kernel does not actually power off the device using
this method but reboots and leaves it up to the bootloader to actually turn the
power off.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The change adds support of LPC32xx SLC NAND controller.
LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.
This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.
Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.
The driver can be included to an SPL image.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Some NAND controllers define custom functions to read data out,
respect this in order to correctly support bad block handling in
simple SPL NAND framework.
NAND controller specific read_buf() is used even to read 1 byte in
case of connected 8-bit NAND device, it turns out that read_byte()
may become outdated.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
remove unneeded udelay() in this function, as we use
the dev_ready pin.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
The return type of pmic_read and pmic_write is signed int, so
correct variable 'ret' from type unsigned int to int.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
1. Add new regulator driver pfuze100.
* Introduce struct pfuze100_regulator_desc for maintaining info
for one regulator.
2. Add new Kconfig entry DM_REGULATOR_PFUZE100 for pfuze100.
3. This driver intends to support PF100, PF200 and PF3000.
4. Add related macro definition in pfuze header file.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
1. Support driver model for pfuze100.
2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
3. This driver intends to support PF100, PF200 and PF3000, so add
the device id into the udevice_id array.
4. Rename PMIC_NUM_OF_REGS macro to PFUZE100_NUM_OF_REGS.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
If there is no property named 'regulator-name' for regulators,
choose node name instead, but not directly return failure value.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Currently the serial code assumes that there is always at least one serial
port (and panics / crashes due to null pointer dereferences when there is
none).
This makes it impossible to use u-boot on boards where there is no (debug)
serial port, because e.g. all uart pins are muxed to another function.
This commit adds a CONFIG_REQUIRE_SERIAL_CONSOLE Kconfig option, which
defaults to y (preserving existing behavior), which can be set to n on
such boards to make them work.
This commit only implements this for CONFIG_DM_SERIAL=y configs, as allowing
running without a serial port for CONFIG_DM_SERIAL=n configs is non trivial,
and is not necessary at this moment.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add composite video out support.
This only gets enabled on the Mele M3 for now, since that is were it
was tested. It will be enabled on more boards after testing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for interlaced modes, this is a preparation patch for adding
composite out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a few extra sunxi display registers and constant defines.
Also rename some existing defines (e.g. dropping _GCTRL) and make
some more generic (e.g. dropping the 2x scaling from
SUNXI_LCDC_TCON1_TIMING_V_TOTAL).
This is a preparation patch for adding composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We should only subtract 2 from the vblank time when using tcon1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
All the #ifdef-ery in selecting the default and fallback monitor type is
becoming unyielding and makes the code hard to read, replace it with a few
helper functions.
This will also be useful with the upcoming CHIP board which has display
adapter daughterboards which should be runtime detectable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When SPL_NAND_SUNXI option is selected in config, set some configuration
options for sunxi NAND.
This commit also introduces the configurable options in Kconfig.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This driver adds NAND support to SPL.
It was tested on Allwinner A20.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fix most of the dangling checkpatch issues, no functional change.
There are still 7 warnings, 1 checks , but those are left in place
for the sake of readability of the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_misc_config
instead of the various macros. This is just an sed exercise here, no
manual coding needed.
This patch actually removes the need to include any board-specific
files in sequencer.c , so sequencer.c namespace is now no longer
poluted by QTS-generated macros.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This is another macro used to obfuscate the real code. The
T(INIT|RESET)_CNTR._VAL is always defined, so this indirection
is unnecessary. Get rid of this.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Just use READ_VALID_FIFO_SIZE directly, no need for this macro obfuscation.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_misc_config to wrap the remaining
misc configuration values in board file. Again, introduce a function,
socfpga_get_sdram_misc_config(), which returns this the structure. This
is almost the final step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_io_config
instead of the IO_* macros. This is just an sed excercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_io_config to wrap the IO configuration
values in board file. Introduce socfpga_get_sdram_io_config() function,
which returns this the structure. This is another step toward wrapping
the nasty QTS generated macros in board files and reducing the pollution
of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_rw_mgr_config
instead of the RW_MGR_* macros. This is just an sed exercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_rw_mgr_config to wrap the RW manager
configuration values in board file. Introduce a complementary function,
socfpga_get_sdram_rwmgr_config(), which returns this the structure.
This is another step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce two wrapper functions, socfpga_get_seq_ac_init() and
socfpga_get_seq_inst_init() to avoid direct inclusion of the
sequencer_auto_ac_init.h and sequencer_auto_inst_init.h QTS
generated files. This reduces namespace pollution again.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This is defined in the QTS-generated headers, so it must not be
re-defined in sequencer.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
These parameters are not used in the code, zap them and the
macros which are used by them as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Move the files generated by QTS into the board directory, they should not
be part of the driver files at all.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Originally, both sdram_start and sdram_end were 64b values. The
sdram_start had no reason for being so, since our address space
is only 32b, so switching sdram_start to u32 is simple.
The sdram_end is a bit more complex, since it can actually be
set to (1 << 32) if someone really wanted to use an SoCFPGA with
4 GiB of DRAM and fixed the code around a little. But, the code
handling the protection rules internally decrements the sdram_end
variable anyway. Thus, instead of calling the code and passing in
the address of the SDRAM end, pass in the address already decremented
by one. This lets the sdram_end be 32b as well.
Signed-off-by: Marek Vasut <marex@denx.de>
