Commit graph

62926 commits

Author SHA1 Message Date
Vignesh Raghavendra
5502c88e67 spi: ti_qspi: Add support for CS other than CS0
Make sure corresponding setup registers are updated depending on CS.
This ensures that driver can support QSPI flashes on ChipSelects other
than on CS0

Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-27 22:27:22 +05:30
Marcin Wojtas
f7dd537098 spi: prevent overriding established bus settings
The SPI stack relies on a proper bus speed/mode configuration
by calling dm_spi_claim_bus(). However the hitherto code
allowed to accidentally override those settings in
the spi_get_bus_and_cs() routine.

The initially established speed could be discarded by using
the slave platdata, which turned out to be an issue on
the platforms whose slave maximum supported frequency
is not on par with the maximum frequency of the bus controller.

This patch fixes above issue by configuring the bus from
spi_get_bus_and_cs() only in case it was not done before.

Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-27 22:27:22 +05:30
Marek Vasut
6954756a15 cmd: spi: Permit setting bus frequency
The 'sspi' command hard-coded 1 MHz bus frequency for all transmissions.
Allow changing that at runtime by specifying '@freq' bus frequency in Hz.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-27 22:27:21 +05:30
Bin Meng
bfcd9298b2 test: dm: spi: Fix sandbox dm_test_spi_find()
Per sandbox_cs_info(), sandbox spi controller only supports chip
select 0. Current test case tries to locate devices on chip select
1, and any call to spi_get_bus_and_cs() or spi_cs_info() with cs
number 1 should not return 0.

This updates the test case to handle it correctly.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-27 22:27:21 +05:30
Bin Meng
7bacce524d dm: spi: Check cs number before accessing slaves
Add chip select number check in spi_find_chip_select().

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
2020-01-27 22:27:21 +05:30
Michael Walle
383fded70c spi: nxp_fspi: new driver for the FlexSPI controller
This is a port of the kernel's spi-nxp-fspi driver. It uses the new
spi-mem interface and does not expose the more generic spi-xfer
interface. The source was taken from the v5.3-rc3 tag.

The port was straightforward:
 - remove the interrupt handling and the completion by busy polling the
   controller
 - remove locks
 - move the setup of the memory windows into claim_bus()
 - move the setup of the speed into set_speed()
 - port the device tree bindings from the original fspi_probe() to
   ofdata_to_platdata()

There were only some style change fixes, no change in any logic. For
example, there are busy loops where the return code is not handled
correctly, eg. only prints a warning with WARN_ON(). This port
intentionally left most functions unchanged to ease future bugfixes.

This was tested on a custom LS1028A board. Because the LS1028A doesn't
have proper clock framework support, changing the clock speed was not
tested. This also means that it is not possible to change the SPI
speed on LS1028A for now (neither is it possible in the linux driver).

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
2020-01-27 22:27:21 +05:30
Tom Rini
051e03c0d7 Merge tag 'u-boot-clk-26Jan2020' of https://gitlab.denx.de/u-boot/custodians/u-boot-clk
- Various clock fixes and enhancements
2020-01-27 07:19:26 -05:00
Pedro Jardim
2f39ab1649 clock_imx8mq: Make frac_pll_init() static
Since frac_pll_init() is only used in this file, change it to 'static'.

This fixes the following sparse warning:

arch/arm/mach-imx/imx8m/clock_imx8mq.c:662:5: warning: no previous
prototype for ‘frac_pll_init’ [-Wmissing-prototypes]

Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
2020-01-26 21:57:09 +01:00
Pedro Jardim
852cd55ea7 clock_imx8mq: Remove the function sscg_pll_init()
Function sscg_pll_init() is not used anywhere, so it can simply be deleted.
This was found because of the following sparse
warning:

arch/arm/mach-imx/imx8m/clock_imx8mq.c:702:5: warning: no previous prototype for ‘sscg_pll_init’ [-Wmissing-prototypes]
 int sscg_pll_init(u32 pll)
     ^~~~~~~~~~~~~

Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
2020-01-26 21:57:08 +01:00
Pedro Jardim
953d02f001 clock_imx8mq: Make do_imx8m_showclocks() static
Since do_imx8m_showclocks() is only used inside this file, make it 'static'.

This fixes the following sparse warning:

arch/arm/mach-imx/imx8m/clock_imx8mq.c:836:5: warning: no previous prototype
 for ‘do_imx8m_showclocks’ [-Wmissing-prototypes]
 int do_imx8m_showclocks(cmd_tbl_t *cmdtp, int flag, int argc,
     ^~~~~~~~~~~~~~~~~~~

Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
2020-01-26 21:57:08 +01:00
Pedro Jardim
fb3c4d926f clock_imx8mq: Delete not used init_usb_clk()
Function init_usb_clk() is not used anywhere, so it can simply be deleted.
This was detected by the following sparse warning:

arch/arm/mach-imx/imx8m/clock_imx8mq.c:377:6: warning: no previous prototype
 for ‘init_usb_clk’ [-Wmissing-prototypes]
 void init_usb_clk(void)
      ^~~~~~~~~~~~

Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
2020-01-26 21:57:08 +01:00
Giulio Benetti
041b06a7c3 clk: imx: pllv3: fix potential 'divide by zero' in av_set_rate()
Guard 'parent_rate==0' to prevent 'divide by zero' issue in
clk_pplv3_av_set_rate(). If it is 0, let's return with -EINVAL.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-26 21:57:08 +01:00
Giulio Benetti
d37ecaba88 clk: imx: pllv3: fix potential 'divide by zero' in av_get_rate()
Guard 'mfd==0' to prevent 'divide by zero' issue in
clk_pplv3_av_get_rate(). If it is 0, let's return with EIO since mfd
should never be 0 at all.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-26 21:57:08 +01:00
Giulio Benetti
3391e77729 clk: imx: pllv3: fix potential 'divide by zero' in sys_get_rate()
Guard 'parent_rate==0' to prevent 'divide by zero' issue in
clk_pplv3_sys_get_rate(). If it is 0, let's return with -EINVAL.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-26 21:57:08 +01:00
Angelo Durgehello
c05b38df47 common: fix regression on block cache init
m68k needs block cache list initialized after relocation.
Other architectures must not be involved.

Fixing regression related to:

commit 1526bcce0f
	("common: add blkcache init")

Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-26 13:36:14 -05:00
Joel Johnson
080dbc64fc arm: mvebu: fix A38x breakage from commit bb872dd930
This function parameter usage of load_addr was incorrectly caught in
the clarifying renames of commit bb872dd930, which results in boot
failures on Marvell A38x.

Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Patch-to: Simon Glass <sjg@chromium.org>
2020-01-26 13:36:07 -05:00
Tom Rini
0b23b0d9f9 Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-sunxi
- Libre Computer ALL-H3-IT/ALL-H5-CC board (Chen-Yu Tsai)
- Allwinner R40 Ethernet, usb phy enablement (Andre Przywara)
- Sunxi auto load from 128KB MMC offset (Andre Przywara)
- Orange Pi Win Ethernet phy enablement (Jernej Skrabec)
2020-01-26 12:05:11 -05:00
Jernej Skrabec
2936eb2d55 configs: Orange Pi Win: enable ethernet phy
Orange Pi Win has gigabit ethernet port, but default U-Boot
configuration for that board enabled ethernet driver but
didn't enable realtek phy.

Fix that.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-26 20:59:51 +05:30
Andre Przywara
7c841d844f sunxi: Automate loading from 128KB MMC offset
Since commit 067e0b9684 ("sunxi: Allow booting from 128KB SD/eMMC offset")
we support having the SPL loaded from either the traditional 8KB SD
card/eMMC offset, or from the alternative location at 128KB. However the
sector to find the U-Boot image was still hard-coded at compile time,
and had to be adjusted for one of the two choices.

Since we can actually override the function to return the sector offset,
we can just check the boot source byte there to select the proper offset
based on from where the SPL was loaded.

This allows the very same binary image to be loaded from either 128KB or
8KB, with the U-Boot proper image always being located just behind the SPL.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-26 19:10:16 +05:30
Andre Przywara
ee98d76893 sunxi: SPL: Factor out sunxi_get_boot_source()
The Boot ROM write some boot source ID (SD card, eMMC, SPI, ...) into
a certain location in SRAM, so the SPL can easily determine where to
load U-Boot proper from.
Factor out reading this value, as it will come in handy again shortly.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-26 19:09:34 +05:30
Sean Anderson
90cbfa50c2 clk: Fix error checking of dev_read_addr_ptr
dev_read_addr_ptr returns NULL on error, not FDT_ADDR_T_NONE.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
2020-01-26 12:03:06 +01:00
Sean Anderson
9fca6729c6 clk: Include missing headers for linux/clk-provider.h
This header was missing a couple of include dependencies when included on its
own.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
2020-01-26 12:03:06 +01:00
Giulio Benetti
efbdad3838 clk: uclass: clk_get_by_name() must not be available if CONFIG_OF_PLATDATA is enabled
clk_get_by_name() requires clk_get_by_id() that is not available if
CONFIG_OF_PLATDATA is defined, so move clk_get_by_name() into #else
condition of #if CONFIG_IS_ENABLED(OF_PLATDATA).

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-26 12:03:06 +01:00
Peng Fan
5dcac2b9b3 clk: show more error info when uclass_get_device_by_name
It will ease debug when uclass_get_device_by_name failed with
more error info printed out.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-01-26 12:03:06 +01:00
Fabien Parent
832685f07c clk: mediatek: use unsigned type for returning the clk rate
mtk_clk_find_parent_rate is calling clk_get_rate to know the rate
of a parent clock. clk_get_rate returns a ulong, while
mtk_clk_find_parent_rate returns an int. This implicit cast creates
an issue for clock rates big enough to need the full 32 bits to
store its data. When that happen the clk rate will become incorrect
because of the implicit cast between ulong -> int -> ulong.

This commit change the return type of mtk_clk_find_parent_rate to
ulong.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
2020-01-26 12:03:06 +01:00
Tom Rini
40521a6c90 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
Updates and fixes for ls1028a, lx2160a, ls1012a, ls1021a, ls2080a,
ls1088a platforms:
- lx2-rev2 pcie support, enetc related updates, layerscape-pcie fixes
2020-01-25 12:20:51 -05:00
Tom Rini
d31dd3b596 Merge branch '2020-01-24-master-imports'
- Enable fastboot on some MediaTek platforms
- DMA enchancements
- Assorted bugfixes
2020-01-25 12:04:59 -05:00
Patrick Delaunay
683b7c2a17 mtd: add prototypes for weak function
This patch adds a prototype for the weak function
board_mtdparts_default().

It solves one warning when compiling with W=1 on stm32mp1 board:

board/st/stm32mp1/stm32mp1.c:
     warning: no previous prototype for 'board_mtdparts_default'
              [-Wmissing-prototypes]
     void board_mtdparts_default(const char **mtdids,
                                 const char **mtdparts)
          ^~~~~~~~~~~~~~~~~~~~~~

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-01-25 12:04:36 -05:00
Eric Nelson
50fe8df2c2 common: blk: fix comment about blkcache_read return value
The blkcache_read() routine returns 1 (true) to indicate that a block was
found in the cache and returned, or 0 if not.

Signed-off-by: Eric Nelson <eric@nelint.com>
2020-01-25 12:04:36 -05:00
Shawn Guo
5073e04351 meerkat96: fix typo in MAINTAINERS email address
There is a typo in meerkat96 MAINTAINERS email address.  Fix it.

Reported-by: Carl Gelfand <carl@novtech.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2020-01-25 12:04:36 -05:00
Baruch Siach
3166014d57 genboardscfg.py: drop python version comment
genboardscfg.py requires python 3.x since commit 3bc14098d8
("genboardscfg.py: Convert to Python 3").

Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-01-25 12:04:36 -05:00
Angelo Durgehello
1526bcce0f common: add blkcache init
On m68k, block_cache list is relocated, but next and prev list
pointers are not adjusted to the relocated struct list_head address,
so the first iteration over the block_cache list hangs.

This patch initializes the block_cache list after relocation.

Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
2020-01-25 12:04:36 -05:00
Vignesh Raghavendra
5cde44e12a net: macb: Drop local cache flush
Now that arch specific dma mapping APIs take care of cache
flush/invalidate, drop local cache flush operation.
While at that fix dma_unmap_single() call to match new prototype

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2020-01-25 12:04:36 -05:00
Vignesh Raghavendra
6fff562baf mtd: denali: Drop custom dma mapping functions
Drop local dma_map_single() and dma_unmap_single() and use arch specific
common implementation

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-01-25 12:04:36 -05:00
Vignesh Raghavendra
eaa8b04da3 mmc: tmio-common: Drop custom dma mapping functions
Drop local dma_map_single() and dma_unmap_single() and use arch specific
common implementation

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-01-25 12:04:36 -05:00
Vignesh Raghavendra
c0a5a81f74 asm: dma-mapping.h: Fix dma mapping functions
Subsystems such as USB expect dma_map_single() and dma_unmap_single() to
do dcache flush/invalidate operations as required. For example, see
see drivers/usb/gadget/udc/udc-core.c::usb_gadget_map_request().
Currently drivers do this locally, (see drivers/usb/dwc3/ep0.c,
drivers/mtd/nand/raw/denali.c etc..)
Update arch specific dma_map_single() and dma_unmap_single() APIs to do
cache flush/invalidate  operations, so that drivers need not implement
them locally.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rick Chen <rick@andestech.com>
2020-01-25 12:04:36 -05:00
mingming lee
1fdbad021f fastboot: mt85xx: add command to flash/erase emmc hwpart
This patch includes the following:
1. Add fastboot command to erase the whole EMMC_USER
2. Add fastboot command to flash image at EMMC_BOOT1
3. Add fastboot command to erase the whole EMMC_BOOT1
4. Enale CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT for mt8518

Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2020-01-25 12:04:36 -05:00
mingming lee
dc2426d83a configs: mt8518: Enable fastboot related configs
Enable EFI module.
Enable fastboot.

Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2020-01-25 12:04:36 -05:00
mingming lee
d33be18833 configs: mt8518: enable usb gadget driver
Enable board_late_init and usb gadget for mt8518

Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2020-01-25 12:04:36 -05:00
mingming lee
dafd97ff70 configs: mt8518: set global variables for fastboot
set common fastboot variables for mt8518

Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2020-01-25 12:04:36 -05:00
mingming lee
e65016150e ARM: Mediatek: Add board_late_init to init usb gadget driver
Add board_late_init function to init usb gadget driver for mt8518

Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2020-01-25 12:04:36 -05:00
mingming lee
7d017d607e usb: musb-new: mt85xx: add musb-new gadget driver.
Using musb-new structure for mt85xx gadget driver.
Add gadget driver dts for mt8518 SoCs.

Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2020-01-25 12:04:36 -05:00
Heinrich Schuchardt
94a8e83a60 crypto: make mod_exp_sw() static
Function mod_exp_sw() is only used via the operators of the uclass.
It is not defined in any include.

Make mod_exp_sw() static.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-01-25 12:04:36 -05:00
Heinrich Schuchardt
1611235b85 lib: Kconfig dependencies for pseudo-random library
drivers/rng/sandbox_rng.c requires rand() to be defined but configuration
option CONFIG_CONFIG_LIB_RAND selected in drivers/rng/Kconfig does not
exist.

test/lib/test_aes.c requires rand() to be defined.

Fix the selection criteria for choice "Pseudo-random library support type".

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-01-25 12:04:36 -05:00
Heinrich Schuchardt
1b27753a96 lib: rsa: consider CONFIG_SPL_RSA
CONFIG_SPL_RSA is meant to control if lib/rsa/* is used for SPL. Adjust
lib/Makefile to consider this setting.

This was correctly setup with commit 51c14cd128 ("verified-boot: Minimal
support for booting U-Boot proper from SPL") and got lost with commit
089df18bfe ("lib: move hash CONFIG options to Kconfig").

Fixes: 089df18bfe ("lib: move hash CONFIG options to Kconfig")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-01-25 12:04:36 -05:00
Chen-Yu Tsai
533f2433ff sunxi: Add Libre Computer ALL-H5-CC H5 board
The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:

  - Gigabit Ethernet via external RTL8211E Ethernet PHY
  - 16 MiB SPI NOR flash memory
  - PoE tap header
  - Line out jack removed

Only H5 variant test samples were made available, and the vendor is not
certain whether other SoC variants would be made or not. Furthermore the
board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree
simply includes the one for the ALL-H3-CC, and adds the changes on top.

The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24 23:13:55 +05:30
Chen-Yu Tsai
986b5e8c4a sunxi: Add Libre Computer ALL-H3-IT H5 board
The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.

The board features:

  - H2, H3, or H5 SoC from Allwinner
  - 2 DDR3 DRAM chips
  - Realtek RTL8821CU based WiFi module
  - 128 Mbit SPI-NOR flash
  - micro-SD card slot
  - micro HDMI video output
  - FPC connector for camera sensor module
  - generic Raspberri-Pi style 40 pin GPIO header
  - additional pin headers for extra USB host ports, ananlog audio and
    IR receiver

Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.

The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24 23:09:47 +05:30
Andre Przywara
671d64fe35 sunxi: move CONFIG_SYS_SPI_U_BOOT_OFFS out of defconfig
For Allwinner SoCs the CONFIG_SYS_SPI_U_BOOT_OFFS value is not really a
board choice: The boot ROM only loads the SPL from offset 0 of the SPI
NOR flash, and loads at most 32KB. This is a similar situation as on MMC,
so consequently we create our "joint" image (SPL + U-Boot proper) with
that 32KB offset during the build.

So define the value of this symbol to be 32KB by default for every
Allwinner SoC. This removes the definition of this symbol from the
_defconfig files, and avoids every board to define this over and over
again.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24 23:06:56 +05:30
Andre Przywara
043c65b793 sunxi: defconfig: R40 boards: enable USB
Now that the USB PHY on the Allwinner R40 SoC is supported, enable USB
support for the two R40 boards U-Boot supports.
For this we need to add the GPIO pin that powers the USB port(s), also
enable the usual suspects (OHCI/EHCI support).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24 23:06:50 +05:30
Andre Przywara
a2f729f49b phy: sun4i-usb: Add Allwinner R40 support
Since every Allwinner USB PHY seems to be slightly different from each
other, we need to add the compatible string and the respective data
structure to make it work on the R40/V40 SoC.
Nothing spectacular this time, just one less USB controller than the H3.
Copied from the Linux kernel.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24 23:06:50 +05:30