To keep a consistent MMC device mapping in SPL and in u-boot, let's
register the MMC controllers the same way in u-boot and in the SPL.
In terms of boot time, it doesn't hurt to register more controllers than
needed because the MMC device is initialized only prior being accessed for
the first time.
Having the same device mapping in SPL and u-boot allows us to use the
environment in SPL whatever the MMC boot device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Add MAC support.
Use PHY, connected to RGMII1 as a default Eth adapter,
by appropriate setting of 'cpsw_data.active_slave'.
'cpsw_phy' env variable can override this setting.
Set the MAC addresses in the U-Boot environment.
The addresses are retrieved from the on-board EEPROM or from the SOC's
MAC fuses.
Set the following PHYs RGMII clock delays:
- Enable RX delay
- Disable TX delay
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: add RGMII clock delays]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Features supported :
* Serial console
* SPI Flash
* MMC/SD Card
* eMMC storage
* SATA
* PCA9555 - GPIO expander over I2C5 bus
* USB
Use spl alternate boot device feature to define fallback to
the main boot device as it is defined by hardware.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: Adjust to v2016.11]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Sometimes devicetree nodes and or properties are added out of the u-boot
console, maybe through some script or manual interaction.
The devicetree as loaded or embedded is quite small, so the devicetree
has to be resized to take up those new nodes/properties.
In original the devicetree was only extended by effective
4 * add_mem_rsv.
With this commit we can add an argument to the "fdt resize" command,
which takes the extrasize to be added.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Simon Glass <sjg@chromium.org>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently MX6 SPL DDR initialization hardcodes the REF_SEL and
REFR fields of the MDREF register as 1 and 7, respectively for
DDR3 and 0 and 3 for LPDDR2.
Looking at the MDREF initialization done via DCD we see that
boards do need to initialize these fields differently:
$ git grep 0x021b0020 board/
board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800
board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800
So introduce a mechanism for users to be able to configure
REFSEL and REFR fields as needed.
Keep all the mx6 SPL users in their current REF_SEL and REFR values,
so no functional changes for the existing users.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
ft_board_setup may return early in the case that the board revision
cannot be obtained. In that case it is assumed that no revision
specific correction in the fdt is neccessary. But the mtd partitions
will not be fixed up either altough they are not revision specific.
Move the call to fdt_fixup_mtdparts in front of the revision specific
part to ensure that the partitions are fixed up even if the board
revision cannot be obtained.
While on it, fix a spelling mistake in a comment introduced by the
same commit.
Fixes: 62d6bac660 ("ARM: board: cm_fx6: fixup mtd partitions in the fdt")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Nikita Kiryanov <nikita@compulab.co.il>
The cm-fx6 module has an on-board st,m25p compatible spi flash chip
used for U-Boot (binary & environment). Overwrite the partitions in
the device tree by the partition table provided in the mtdparts
environment variable, if it is set.
This allows to specify a kernel independent partitioning in the
environment and provides a convient way for the user to adapt the
partition table.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Old revisions of Utilite (based on cm-fx6) do not have a dedicated
card detect pin. But the card is removable by the user and card
detection can be realized with polling (e.g. supported by Linux).
Add the broken-cd property to the mmc device tree instead of the
non-removable property to make card detection possible if polling
is supported.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Add layout definitions and implement functions for field printing/updating,
layout detection, layout assignment, and layout parsing.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
There is no distinction between essential and non-essential mux configuration,
so it doesn't make sense to have an "essential" prefix.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
During boot, U-Boot raises the CPU frequency but the CORE and MPU regulators
are not updated. This is not a problem in cold boot since the default values
that the pmic outputs are correct, but if Linux were to switch the module to a
low power OPP, the new voltage values will be retained after a reboot and the
module will likely hang once U-Boot raises the CPU frequency back up.
Set both CORE and MPU regulators to to 1.1V on boot.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
CM-T43 does not have a vtt regulator. Remove the function that's supposed
to enable it.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Set TPS65218 FSEAL bit to 1 so that RTC could be powered using on-board
3V battery. This is necessary so that time and date will survive reboots and
power offs.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simplify the board file by splitting it to spl portion and u-boot portion.
Some unnecessary includes were identified and removed. No functional changes.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adjust all Tegra boards to use driver model for Ethernet, now that the
required drivers are converted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
CM-T3517 has several HW revisions.
Add board specific get_board_rev() callback to retrieve revision number.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Igor Grinberg <grinberg@compulab.co.il>
Use spl alternate boot device feature to define fallback to
the main boot device as it is defined by hardware.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add the following splash locations to cm-fx6:
* filesystem formatted mmc
* filesystem formatted usb
* filesystem formatted sata
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add support for loading splash image from an SD card formatted with
a filesystem. Update boards to maintain original behavior where needed.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
This introduces omap_die_id_display to display the full die id.
There is no need to store it in an environment variable, that no boot script
is using anyway.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Old revisions of Utilite (a miniature PC based on cm-fx6) do not have
a card detect for mmc, and thus the kernel needs to be told that
there's a persistent storage on usdhc3 to force it to probe the mmc
card.
Check the baseboard revision and modify the device tree accordingly
if needed.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Introduce cl_eeprom_get_product_name() for obtaining product name
from the eeprom.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
cl_eeprom_read_mac_addr() doesn't differentiate between success case and
inability to access eeprom. Fix this by propagating the return value of
cl_eeprom_setup().
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add support for selecting which eeprom is queried for board revision by
extending cl_eeprom_get_board_rev() to accept an i2c bus number.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
On some CM-FX6 modules U-Boot attempts to configure the usb0 controller in
device mode, which renders it unavailable:
USB0: Port not available.
and also causes usb stop to report an error
EHCI failed to shut down host controller.
This happens mostly on MX6 Dual based modules, and is caused by the USBPHY_CTRL
register reporting USBPHY_CTRL_OTG_ID to be 1, even when it is pulled down.
Since we do not support device mode in cm-fx6 u-boot, force all controllers to
be configured as hosts.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add initial support for CM-T43, an AM437x based SoM.
This support includes: serial, MMC/eMMC, NAND, USB, ETH, I2C, GPIO, DRAM
detection.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Refactor display code to only setup hdmi if do_enable_hdmi() is invoked.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add support for selecting display preset using the environment variable
"displaytype". This is a preparation for future merging of compulab
omap3_display.c display selection code with the cm-fx6 display selection code.
The "panel" environment variable is retained for backwards compatibility.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Implement a cm-fx6 specific board_video_skip() to provide the option to not
initialize the display.
The new function does not init display if the environment variable "panel" is
not defined, or if it is set to an unsupported value.
Collateral changes:
- Don't use the global displays array (it's CONFIG_IMX_VIDEO_SKIP specific).
- Don't use detect_hdmi(), since env controlled init makes it unnecessary.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
U-Boot does not explicitly assign the display to an IPU interface. Instead, it
relies on the power-on default of DI0.
Since the kernel reassigns HDMI display to DI1, after a warm reset the HDMI
display no longer works in U-Boot.
Fix this by explicitly assigning HDMI to IPU1 DI0 in U-Boot.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This introduces OMAP3 support for the common omap boot code, as well as a
major cleanup of the common omap boot code.
First, the omap_boot_parameters structure becomes platform-specific, since its
definition differs a bit across omap platforms. The offsets are removed as well
since it is U-Boot's coding style to use structures for mapping such kind of
data (in the sense that it is similar to registers). It is correct to assume
that romcode structure encoding is the same as U-Boot, given the description
of these structures in the TRMs.
The original address provided by the bootrom is passed to the U-Boot binary
instead of a duplicate of the structure stored in global data. This allows to
have only the relevant (boot device and mode) information stored in global data.
It is also expected that the address where the bootrom stores that information
is not overridden by the U-Boot SPL or U-Boot.
The save_omap_boot_params is expected to handle all special cases where the data
provided by the bootrom cannot be used as-is, so that spl_boot_device and
spl_boot_mode only return the data from global data.
All of this is only relevant when the U-Boot SPL is used. In cases it is not,
save_boot_params should fallback to its weak (or board-specific) definition.
save_omap_boot_params should not be called in that context either.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
enable_spi_clock does the same thing with enable_cspi_clock, so
remove enable_cspi_clock.
Remove enable_cspi_clock prototype in header file
convert cm_fx6/spl.c to use enable_spi_clk
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
All the Tegra boards borrow the files from board/nvidia/common/
directory, i.e., board/nvidia/common/* are not vendor-common files,
but SoC-common files.
Move NVIDIA common files to arch/arm/mach-tegra/ to clean up
Makefiles.
As arch/arm/mach-tegra/board.c already exists, this commit renames
board/nvidia/common/board.c to arch/arm/mach-tegra/board2.c,
expecting they will be consolidated as a second step.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
As mentioned in the previous commit, adding default values in each
Kconfig causes problems because it does not co-exist with the
"depends on" syntax. (Please note this is not a bug of Kconfig.)
We should not do so unless we have a special reason. Actually,
for CONFIG_DM*, we have no good reason to do so.
Generally, CONFIG_DM is not a user-configurable option. Once we
convert a driver into Driver Model, the board only works with Driver
Model, i.e. CONFIG_DM must be always enabled for that board.
So, using "select DM" is more suitable rather than allowing users to
modify it. Another good thing is, Kconfig warns unmet dependencies
for "select" syntax, so we easily notice bugs.
Actually, CONFIG_DM and other related options have been added
without consistency: some into arch/*/Kconfig, some into
board/*/Kconfig, and some into configs/*_defconfig.
This commit prefers "select" and cleans up the following issues.
[1] Never use "CONFIG_DM=n" in defconfig files
It is really rare to add "CONFIG_FOO=n" to disable CONFIG options.
It is more common to use "# CONFIG_FOO is not set". But here, we
do not even have to do it.
Less than half of OMAP3 boards have been converted to Driver Model.
Adding the default values to arch/arm/cpu/armv7/omap3/Kconfig is
weird. Instead, add "select DM" only to appropriate boards, which
eventually eliminates "CONFIG_DM=n", etc.
[2] Delete redundant CONFIGs
Sandbox sets CONFIG_DM in arch/sandbox/Kconfig and defines it again
in configs/sandbox_defconfig.
Likewise, OMAP3 sets CONFIG_DM arch/arm/cpu/armv7/omap3/Kconfig and
defines it also in omap3_beagle_defconfig and devkit8000_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now CONFIG_SPL_BUILD is not defined in Kconfig, so
"!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Move board/compulab/common/splash.c code to
common/splash_source.c to make it available for everybody. This move
renames cl_splash_screen_prepare() to splash_source_load(), and
the compilation of this code is conditional on CONFIG_SPLASH_SOURCE.
splash_source features:
* Provide a standardized way for declaring board specific splash screen
locations
* Provide existing routines for auto loading the splash image from the
locations as declared by the board
* Introduce the "splashsource" environment variable, which makes it
possible to select the splash image source.
cm-t35 and cm-fx6 are updated to use the modified version.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add support for splash screen.
The splash screen is loaded from the SPI flash and is displayed on the
HDMI display.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[grinberg@compulab.co.il: minor code and commit message updates]
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Add support for loading splash from sf.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[grinberg@compulab.co.il: staticize the sf global variable]
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
