Move init code of low-level debug into a single file.
This is helpful to create an image that runs on multiple SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, IECTRL is enabled after pin-mux settings for the low-level
debugging for PH1-LD4 and PH1-sLD8. While IECTRL is disabled, input
signals are pulled-down, i.e. glitch signal (Low to High transition)
problem occurs if pin-mux is set up first. As a result, one invalid
character is input to the UART block and the auto-boot counting is
terminated immediately.
The correct initialization procedure is:
[1] Enable IECTRL (if IECTRL exists for the pins)
[2] Set up pin-muxing
[3] Deassert the reset of the hardware block
Currently, the low-level debugging is working for PH1-sLD3 and
PH1-Pro4, but just in case, follow the sequence for all the SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
To achieve the complete run-time configuration by device trees, ifdef
conditionals in header files are not preferable.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Historically (for compatibility with very old platforms), two
different types of micro support cards have been used with the
UniPhier SoC development boards. It has been painful to maintain
both. Having one of them is enough.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These input enable settings are handled by the pinctrl drivers.
Because the external bus pins are input-enabled by default, on-board
devices such as LED still work fine even with this delayed input
enabling.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As the UniPhier serial driver had already switched to Drive Model
and the pinctrl drivers are now enabled, these pin-muxing settings
are properly handled by the pinctrl drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Device Tree really improves code maintainability and is now
available for SPL too.
This is the state-of-the-art implementation in U-boot.
The board files (platform data) are no longer needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the Linux coding style, it is recommended to include <linux/io.h>
rather than <asm/io.h>. Follow this trend.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The UniPhier platform is going to enable Driver Model and UART
support on SPL. Move UART pin settings to early_pin_init(),
which is called from SPL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The two Makefiles arch/arm/mach-uniphier/{ph1-ld4,ph1-sld8}/Makefile
are completely the same. We can improve the maintainability by
having one to include the other.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Two support card variants are used with UniPhier reference boards:
- 1 chip select support card (original CPLD)
- 3 chip selects support card (ARIMA-compatible CPLD)
Currently, the former is only supported on PH1-Pro4, but it can be
expanded to PH1-LD4, PH1-sLD8 with a little code change.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Now UniPhier platform highly depends on Device Tree configuration
(CONFIG_OF_CONTROL is select'ed by Kconfig). Since the EHCI is only
used on main U-Boot, we can drop platform devices of the EHCI
controllers. We still keep UART platform devices because they might
be useful for SPL.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Split the current clkrst_init() into two functions:
- early_clkrst_init(): called from SPL
Deassert the reset signals of the memory controller and some other
basic cores.
- clkrst_init(): called from main U-boot
Deassert the reset signals that are necessary for the access to
peripherals etc.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Now UniPhier SoCs only work with CONFIG_SPL and the function
sbc_init() is called from SPL.
The conditional #if !defined(CONFIG_SPL_BUILD) has no point
any more.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since commit 0e7368c6c4 (kbuild: prepare for moving headers into
mach-*/include/mach), we can replace #include <asm/arch/*.h> with
<mach/*.h> so we do not need to create the symbolic link during the
build.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
