Add device tree for P5040DS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for P4080DS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for P3041DS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for P1041RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for P1020RDB boards and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for P1020RDB boards and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for T1042D4RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for T1024RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for T4240RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for T2080RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The SPI and NAND variants enable DM_GPIO, so this patch enables
DM_GPIO for the NOR / XIP version of the da850-evm.
Signed-off-by: Adam Ford <aford173@gmail.com>
The NAND configuration has had the ethernet missing, so this patch
enables the on-board ethernet interface.
Signed-off-by: Adam Ford <aford173@gmail.com>
To address the following warning message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
CONFIG_DM_USB is enabled, this resulted in SPL build errors:
drivers/built-in.o: In function 'xhci_dwc3_probe':
u-boot/drivers/usb/host/xhci-dwc3.c:155: undefined reference to 'usb_get_dr_mode'
scripts/Makefile.spl:404: recipe for target 'spl/u-boot-spl' failed
make[1]: *** [spl/u-boot-spl] Error 1
Makefile:1721: recipe for target 'spl/u-boot-spl' failed
make: *** [spl/u-boot-spl] Error 2
Enabling usb common library and usb ethernet drivers in SPL
does the job. Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
earlyprintk no longer works on arm64 platforms. Replace it with earlycon
which works fine.
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: Liviu Dudau <liviu.dudau@foss.arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add two new configurations (qemu-riscv{32,64}_spl_defconfig) with SPL
enabled for RISC-V QEMU. QEMU does not require SPL to run U-Boot. The
configurations are meant to help the development of SPL on RISC-V.
The configurations enable RAM as the only SPL boot device. Images must
be loaded at address 0x80200000. In the default boot flow, U-Boot SPL
starts in machine mode, loads the OpenSBI FW_DYNAMIC firmware and U-Boot
proper from the supplied FIT image, and starts OpenSBI. U-Boot proper is
then started in supervisor mode by OpenSBI.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
This converts the following to Kconfig:
CONFIG_SYS_SPI_U_BOOT_OFFS
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini <trini@konsulko.com>
the x530 board needs conversion of SPL_SPI_LOAD to Kconfig first
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Convert CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig, update defconfigs,
headers and whitelist.
Please note that this symbol already was used in Kconfig
(imply in CONFIG_NAND_ATMEL) which did not work, since this symbol was
not available in Kconfig. This changes now with this patch and all
boards with CONFIG_NAND_ATMEL will have BBT enabled. Which is what
I also need on my GARDENA AT91SAM based board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
[trini: Rework such that the configs are unchanged to start with]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
- remove rk3288 fennec board
- remove SPL raw image support for Rockchip SoCs
- add common misc_init_r() for ethaddr from cpuid
- enable USB HOST support for rk3328
- unify code for finding a valid gpt in part driver
This converts the following to Kconfig:
CONFIG_FSL_USDHC
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MXS_GPIO
Travis-CI: https://travis-ci.org/lmajewski/u-boot-dfu/builds/571260789
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Enable USB host support on GR Peach board.
To use USB host on GR Peach, it might be necessary to solder JP3 header
onto the board first and then short it. Shorting JP3 is mandatory to let
the U5 regulator to supply VBUS to the CN3 USB port.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Enable related configs on all ls1088aqds boards to support pcf2127
rtc DM function.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable related configs on all ls2088aqds boards to support ds3231
rtc DM function.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable related configs on all ls1028aqds boards to support pcf2127
rtc DM function.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Tested-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable related configs on all lx2160ardb boards to support pcf2127
rtc DM feature.
Also remove SYS_I2C_MXC_I2Cx, where x is from 1 to 8 from
Kconfig.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Move CONFIG_FSL_QSPI from header file to defconfigs,
consequently unset imply config(CONFIG_SPI_FLASH_BAR) which
is not valid for LS series.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
With DM_MMC enabled, enable CONFIG_BLK to remove this
compile warning for am43xx based targets:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Targets were compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Sorry for the noise, but there appears to be a regression with older
hardware. Since it broke the direct_nor boot option, it should be
reverted until a better solution is available.
This reverts commit 51cd1e2373.
Updates jerry, mickey, minnie and speedy defconfigs to:
- fit the SPL in 32k
- boot from SPI (only)
- remove gadget support (these have no OTG port)
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Rebase on top of tree)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This affects RK3036, RK322X and RK3288 - the defconfig changes done by
moveconfig.py for the veyrons were left out on purpose because they dont
have an OTG port, and will get their config updated in the next commit.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Affects rk3288 veyrons and rk3036, this was mostly done by
moveconfig.py.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Historically there have been various boot options, SPI flash,
NAND or NOR. The NOR flash is mutually exclusive with MMC, but
it isn't mutually exclusive with NAND or SPI Flash, so this patch
enables both NAND flash and SPI Flash when booting from NOR.
Signed-off-by: Adam Ford <aford173@gmail.com>
The configuration with NOR is mutually exclusive with MMC, and as
such, the filesystem commands were disabled. With the USB host
enabled, this patch enables the file system command which can
be executed on storage devices attached to the USB.
Signed-off-by: Adam Ford <aford173@gmail.com>
The current size allocated to U-Boot is 384k, but U-Boot has grown
to 436K which means that saving the environmental variables wipes
out part of the U-Boot source and the board ceases to function.
Due to the sector and erase size for the NOR part and a desire to
not have to change partition sizes often, this patch moves the
U-Boot environmental variables to an offset of 1M so saveenv
does not brick the board. This patch also sets up MTDIDS and
MTDPARTS to clearly show where U-Boot and U-Boot's environmental
variables are located.
Signed-off-by: Adam Ford <aford173@gmail.com>
Enable support for Intel E1000 based PCIe ethernet cards that
can be used to test PCIe RC functionality on AM65x EVM.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This commit adds support for the B&R brsmarc1 SoM.
The SoM is based on TI's AM335x SoC.
Mainly vxWorks 6.9.4.x is running on the board,
doing some PLC stuff on various carrier boards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
This patch disables DM watchdog support for SPL builds and uses
the legacy omap watchdog driver on TI AM335x chipsets.
The following build error is reported if DM watchdog support was
enabled in SPL:
CC spl/drivers/usb/gadget/rndis.o
LD spl/drivers/usb/gadget/built-in.o
LD spl/drivers/usb/musb-new/built-in.o
LD spl/drivers/built-in.o
LD spl/u-boot-spl
arm-linux-ld.bfd: u-boot-spl section .u_boot_list will not fit in region .sram
arm-linux-ld.bfd: region .sram overflowed by 440 bytes
make[1]: *** [spl/u-boot-spl] Error 1
make: *** [spl/u-boot-spl] Error 2
Adjusted WATCHDOG_RESET macro accordingly. Earlier it was pointing
to hw_watchdog_reset. Since CONFIG_WATCHDOG replaces CONFIG_HW_WATCHDOG,
now WATCHDOG_RESET macro points to watchdog_reset. This watchdog_reset
is not defined anywhere for am33xx/omap2 and needs to be defined. Fixed
this by simply calling hw_watchdog_reset in watchdog_reset.
Built and tested on AM335x device (BeagleboneBlack), compile tested for
all other AM33xx/omap2 based boards.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
[trini: Fix watchdog.h logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds device tree and driver model watchdog support,
converts the legacy omap watchdog driver to driver model for
TI AM335x chipsets. The following compile warning is removed:
===================== WARNING ======================
This board does not use CONFIG_WDT (DM watchdog support).
Please update the board to use CONFIG_WDT before the
v2019.10 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
CONFIG_HW_WATCHDOG is no more a default option for AM33XX devices
after DT/DM conversion, adjusted kconfig accordingly.
DM watchdog support is enabled by default in SPL. The SPL image
doesn't fit into SRAM because of size constraints and build breaks
with an overflow. For this reason DM watchdog support should be
disabled in SPL, driver code should be adjusted accordingly to serve
this purpose.
Built and tested on AM335x device (BeagleboneBlack), compile tested
for all other AM33xx based boards.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Disable the PSCI_RESET reboot handler to permit handling the reboot
flag and calling the PSCI handler with the flag in parameter.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SEI510 board is based on the Amlogic S905X2 SoC
from the Amlogic G12A SoC family.
The board has the following specifications :
- Amlogic S905X2 ARM Cortex-A53 quad-core SoC
- XGB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module
The board default behaviour is for booting Android and triggers
fastboot on recovery or reboot mode.
USB vendor ID (used by fastboot) is 0x18d1 (Google) for
default udev rules for existing android users work out of the box.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add Macronis SPI flash support - some Omnia routers are shipped with
this SPI flash chip.
Also add the memtest command to defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The mvgbe driver supports DM_ETH so switch these boards to using it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This board is unmaintained and can be removed. This also allows us to
remove kmp204x-common.h and integrate it in kmp204x.h.
Signed-off-by: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove the PORTL2 board and all its dependencies as it is no longer
supported by the company.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
To execute the conversion away from board specific header files, Kconfig
menus have been implemented for all KM boards and additionally for those
having an ARM architecture.
For the moment, the preprocessor definitions stay in the headers. The
boolean types, however, needed a modification (#define CONFIG_* 1).
The default configuration files of some boards required an update in order
to not change the currently defined values of the configurations.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit adds board support for Hikey960 board from Hisilicon. This
board is one of the Consumer Edition boards of the 96Boards family
powered by Kirin960 SoC.
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/hikey960/
The initial supported/tested devices include:
- Debug serial
- SD
With these support, it's good enough for loading Linux Kernel from SD.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- Enable SD slot on Intel Edison
- Populate CSRT ACPI table for shared DMA controller on Intel Tangier
- Convert Intel ICH-SPI driver to use new spi-mem ops
- Enable config_distro_bootcmd for QEMU x86
- Support U-Boot as a payload for Intel Slim Bootloader
- Avoid writing temporary asl files into the source tree which fixes the
parallel build issue occasionally seen
Support the V1.2 hardware revision with the following pin muxing
changes:
Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4
are now used as DDC pins.
Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are
now used as USB power enable signals.
Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power
enable signals are now used as GPIO3 and GPIO4.
Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is
loaded on V1.2 and later modules and resp. USB power enable signals
activated.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use unified values for USB Product/Vendor numbers
when the config block is missing
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We never really added a sensible DFU configuration for platforms
based on eMMC. Most of the things one might want to do can also be done
with UMS or fastboot, so drop the DFU configuration.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add slimbootloader board to run U-boot as a Slim Bootloader payload
- Add new board/intel/slimbootloader directory with minimum codes
- Add slimbootloader configuration files
- Add doc/board/intel/slimbootloader.rst
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add slimbootloader board MAINTAINERS file]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Converts qemu x86 machines to boot using distro_config. The intent is to
allow u-boot in qemu to be maximally compatible with many boot methods
without having to change the config. Previously, u-boot would only boot
in a very limited set of circumstances where there was a /boot/vmlinuz
on scsi 0:3 with no ramdisk.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: convert doc updates to reST]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Enable SD slot on Intel Edison platform.
By default firmware doesn't put device on active state. Thus,
we have to do this explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Add rk3399 boards Khadas Edge/-V/-Captain
- Add fully souce code support for rk3328 including TPL/DRAM init
- Enable boot from eMMC for rk3399 rock960/ficus boards
- turn on the IO supply for dw_mmc
This patch will enable the MUSB driver to support mass storage
devices connected to the OTG port in host mode.
Signed-off-by: Adam Ford <aford173@gmail.com>
Until now, binary TPL by Rockchip has been required for booting
procedure. Starting from this commit we may use only u-boot to boot
the device.
Note, that using binary TPL instead of U-boot TPL is still working.
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable driver options for TPL/SPL in evb-rk3328_defconfig.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from commit df4f40acb4 with minor modifications]
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge-Captain.
Khadas Captain is the carrier board for Khadas Edge.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge-V.
Khadas Edge-V is a Khadas VIM form factor Rockchip RK3399 board.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge.
Khadas Edge is an expandable Rockchip RK3399 board with goldfinger.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP
- USB 3.0, 2.0
- USB Type C power and data
- 16MB SPI Flash
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since this is part of the autoboot functionality, it makes sense to name
it with an AUTOBOOT prefix. No mainline boards use it so this should be
safe, and downstream boards will need to adjust.
Since this option is just an integer value, it really needs another option
to control whether the feature is enabled or not. Add a new
CONFIG_USE_AUTOBOOT_MENUKEY for that. This fits better with how things are
done with Kconfig, avoiding the need to use a specific value to disable
the feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT
Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.
Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.
Signed-off-by: Simon Glass <sjg@chromium.org>
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
-----BEGIN PGP SIGNATURE-----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=Q5fc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190731' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- sync Amlogic G12A DT with linux 5.3-rc1
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
This patch adds SPI and SPI_FLASH DM support for verified boot on
TI AM335 chipsets. The following compile warning is removed:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Built and tested on AM335x device (BeagleboneBlack).
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
This patch adds BLK and DM support for verified boot on TI AM335x
chipsets. The following compile warnings are removed:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
BLK and DM_MMC are enabled by default in SPL as well, which is
making the build to break with an overflow(spl image doesn't
fit into SRAM because of size constraints).
LD spl/drivers/built-in.o
LD spl/u-boot-spl
arm-linux-ld.bfd: u-boot-spl section .u_boot_list will not fit in region .sram
arm-linux-ld.bfd: region .sram overflowed by 116 bytes
make[1]: *** [spl/u-boot-spl] Error 1
make: *** [spl/u-boot-spl] Error 2
For the above reason BLK and DM_MMC is disabled in SPL.
Built and tested on AM335x device (BeagleboneBlack).
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
The K3 System Controller driver is used for loading and starting
the System Firmware, and is used only on R5 SPL. It need not be
enabled and built for the A72 U-Boot and SPL, so disable it from
the j721e_evm_a72 defconfig.
While at this, also remove the unneeded CONFIG_SPL_REMOTEPROC and
CONFIG_CMD_REMOTEPROC as no remoteprocs are now loaded from A72 SPL.
Signed-off-by: Suman Anna <s-anna@ti.com>
The K3 System Controller driver is used for loading and starting
the System Firmware, and is used only on R5 SPL. It need not be
enabled and built for the A53 U-Boot and SPL, so disable it from
both the GP and HS AM65x A53 defconfigs.
While at this, also remove the unneeded CONFIG_SPL_REMOTEPROC and
CONFIG_CMD_REMOTEPROC as no remoteprocs are now loaded from A53 SPL.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The MTDPARTS currently lists just u-boot.ais as 512k in size.
This works when loading the ais file via serial port, but if one
wanted to update just the u-boot portion, it's not really possible.
This patch splits the MTDPARTS into a 32k SPL partiion and a 480k
u-boot partition which allows u-boot.img to be burned to the u-boot
partition. The remaining partitions are left with the same sizes
and offsets to not break backwards compatibility.
Signed-off-by: Adam Ford <aford173@gmail.com>
We are going to implement DTBO partition for BeagleBoard X15 further. To
support this, 'dtimg' command must be enabled.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
It is essential to have an access to BCB area of 'misc' partition on
Android devices [1]. For BeagleBoard X15 the 'bcb' command will be
further used for reboot reason implementation and booting to recovery.
It can be also used for debugging reasons, like checking RescueParty
messages in BCB area.
[1] doc/android/bcb.txt
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
ODROID-N2 is a single board computer manufactured by Hardkernel Co. Ltd
with the following specifications:
- Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
- 4GB DDR4 SDRAM
- Gigabit Ethernet
- HDMI 2.1 4K/60Hz display
- 40-pin GPIO header
- 4 x USB 3.0 Host, 1 x USB OTG
- eMMC, microSD
- Infrared receiver
The board directory is W400, the name of the Amlogic Reference Design
of Amlogic G12B with Gigabit boards, which will be used for similar
boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Avnet UltraZed-EV Starter Kit is composed by the UltraZed-EV SoM and the
only publicly-available compatible carrier card. The SoM is based on the EV
version of the Xilinx ZynqMP SoC+FPGA.
The psu_init_gpl.c file has been generated from the board definition files
at [0] using Vivado 2018.3 and then minimized by
tools/zynqmp_psu_init_minimize.sh. Manually removed serdes init code since
it is not mentioned in device tree and fixed a checkpatch error.
[0] 3686c9ff7d/ultrazed_7ev_cc/1.1
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Name of this platform has changed and released to customers that's why
name has also changed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: uboot
Enable CONFIG_SPL_DM and enable the driver model for serial by defining
an appropriate device in the board file for da850-lcdk.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We're working towards enabling the driver-model in SPL for da850-lcdk.
Enable CONFIG_USE_TINY_PRINTF in defconfig to reduce SPL size.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We're working towards enabling the driver model in SPL for da850-lcdk.
Enable SPL_SYS_MALLOC_SIMPLE in defconfig to reduce SPL size.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Enable the driver-model on da850-evm. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.
On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Enable the driver-model on da850-lcdk. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.
On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The following warning is emited when building u-boot for da850-lcdk:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI. Please update
the board before v2019.04 for no dm conversion
and v2019.07 for partially dm converted drivers.
Failure to update can lead to driver/board removal
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
While we could fix it by selecting CONFIG_DM_SPI, there's no need to
build it at all as SPI is disabled on da850-lcdk. Remove all unneeded
options from the defconfig.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
There are no more "real" users of CONFIG_DM_I2C_COMPAT and we'll soon
remove it altogether. Stop building it in sandbox mode.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
This option is no longer used on any davinci board but still selected
in defconfigs which causes the following warning:
===================== WARNING ======================
This board uses CONFIG_DM_I2C_COMPAT. Please remove
(possibly in a subsequent patch in your series)
before sending patches to the mailing list.
====================================================
Remove all references to CONFIG_DM_I2C_COMPAT from davinci.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board has been abandonded for a while. I do not have this hardware
and nobody has appeared to notice and/or care that it's orphaned.
Since much of this code is inserted into the da850evm code base, removing
it from support will make da850evm support easier going forward.
This patch removes the da850_am18xxevm_defconfig, README references to this
board and the reference to this board from the MAINTAINERS list.
Signed-off-by: Adam Ford <aford173@gmail.com>
The pumpkin board is made by Gossamer Engineering and is using
a MediaTek SoC. The board currently comes in two available version:
MT8516 SoC and MT8167 SoC.
The board provides the following IOs: eMMC, NAND, SD card, USB type-A,
Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in),
serial over USB, and an expansion header.
Additionally there is a HDMI port, DSI port, and camera port only
on the MT8167 version of the board.
The board can be powered by battery and/or via a USB Type-C port and
is using a PMIC MT6392.
The eMMC and NAND are sharing pins and cannot be used together.
This commit is adding the basic boot support for the Pumpkin MT8516
board on the eMMC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Use CONFIG_DM_VIDEO=y by default for Colibri iMX6ULL.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The SOM-LV and Torpedo boards are very similar, but something
happened growing SPL enough to break the Torpedo. The SOM-LV
board were not doing alias sequencing during SPL and they
continue to work while something broke the Torpedo. This
patch disables SPL_DM_SEQ_ALIAS allowing it to boot again.
Signed-off-by: Adam Ford <aford173@gmail.com>
OHCI was added with DM_USB support, so there are a few unneeded
items in the header file that can be removed. This also
unifies da850evm with NOR and NAND booting options so all have
OHCI support.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate da850_am18xxevm]
Signed-off-by: Tom Rini <trini@konsulko.com>
The OMAP35 and AM/DM37 Torpedo boards do not have a USB
tranceiver connected to the USB host port, so this patch
removes it from the defconfig files.
Signed-off-by: Adam Ford <aford173@gmail.com>
Like the other Logic PD OMAP35/DM37 boards, this board has device
tree enabled for U-Boot. This patch converts the board to enable
SPL_OF_CONTROL and further shrinks the device tree in SPL to limit
it to UART3 (console), MMC1, i2c1, and GPIO4 (for mmc1 CD and WP).
There appears to be a bug in minicom so users may need to
switch the minicom terminal emulation to ANSI from VT102 due
to the junk that gets pushed out of the UART on startup.
Signed-off-by: Adam Ford <aford173@gmail.com>
The PBIAS regulator is available on OMAP3's, and it's shared on
the AM35, so this patch enables that in U-Boot along with GPIO
based regulators.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add initial defconfig support for J721e that runs on A72.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Add MAINTAINERS entry]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add initial defconfig support for J721e that runs on R5.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Add MAINTAINERS file]
Signed-off-by: Tom Rini <trini@konsulko.com>
k3_rproc driver is specifically meant for controlling an arm64
core using TISCI protocol. So rename the driver, Kconfig symbol,
compatible and functions accordingly.
While at it drop this remoteproc selection for a53 defconfig.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now that we removed all legacy boards selecting TI_EMAC we can
completely convert the driver code to using the driver model.
This patch also updates all remaining users of davinci_emac.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
Supported boot media: microSD card (via SPL), QSPI flash.
Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).
Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).
To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.
eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:
- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
get overwritten during copying of the u-boot.bin payload from MMC to
DDR.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have added driver model support to the TSEC driver,
convert ls1021atwr board to use it.
This depends on previous DM series for ls1021atwr:
http://patchwork.ozlabs.org/patch/561855/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[Vladimir] Made the following changes:
- Added 'status = "disabled";' for all Ethernet ports in ls1021a.dtsi
- Fixed the confusion between the SGMII/TBI PCS for enet0 and enet1 -
a mistake ported over from Linux. Each SGMII PCS lies on the private
MDIO bus of the interface (and the RGMII enet2 has no SGMII PCS).
- Added CONFIG_DM_ETH to all ls1021atwr_* defconfigs
- Completely removed non-DM_ETH support from ls1021atwr
- Changed "compatible" string from "fsl,tsec-mdio" to "fsl,etsec2-mdio"
and from "fsl,tsec" to "fsl,etsec2" to match Linux
Enables ethernet, MDIO, PHY drivers for LS1028A RDB and QDS.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since u-boot has added the spi-mem framework and replaced
the spi-nor framework, the mtk_qspi is no longer compatible
with the new spi-nor driver.
Remove this driver along with replacing config item
with new mtk spi-nor driver.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
[jagan: squash related changes and update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- rk3399 lpddr4 support
- rk3399-rock960 board support improvement
- Eliminate pyelftools dependency by make_fit_atf.py
- clean up rockchip dts to use -u-boot.dtsi
- use ARM arch/generic timer instead of rk_timer
- clean up Kconfig options for board support
This adds separate kconfig options for drivers/sysreset and
drivers/firmware.
Up to now, CONFIG_SPL_DRIVERS_MISC_SUPPORT added drivers/misc to SPL
build but also added drivers/firmware and drivers/sysreset at the same
time.
Since that is confusing, this patch uses CONFIG_SPL_SYSRESET for
drivers/sysreset and adds CONFIG_SPL_FIRMWARE for
drivers/firmware (and accordingly for the TPL options).
CONFIG_SPL_DRIVERS_MISC_SUPPORT stays for including drivers/misc into
the SPL build (and accordingly for TPL) since there are boards using
non-DM (non UCLASS_MISC) files from drivers/misc. Such boards don't
have CONFIG_SPL_MISC enabled, so cannot use this to include
drivers/misc into the SPL build.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Due to foot-print issues, we have LPDDR4 code can be
marked as CONFIG_RAM_RK3399_LPDDR4.
So, enable it for Rock-PI-4 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Due to foot-print issues, we have LPDDR4 code can be
marked as CONFIG_RAM_RK3399_LPDDR4.
So, enable it for Rockpro64 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
This patch enables DM I2C for DHCOM i.MX6 PDK2 boards and
removes non DM I2C code. The I2C EEPROM with ethaddr (MAC)
is defined in the device tree. Use UCLASS_I2C_EEPROM
to find the device by fixed hardware path and read the ethaddr.
Tested with DHCOM i.MX6dl and DHCOM i.MX6q.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This patch disables support for running EFI applications on HSC|DDC boards.
As a result - considerable size reduction (~14%) has been observed (for
for u-boot-dtb.imx 475KiB to 407KiB).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Configure fitImage for U-Boot with a device tree for imx6 quad/dual
and duallite/solo. This enables to support the imx6 derivates
quad/dual/duallite/solo with a single binary.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Enable DM support for regulators and fixed regulator driver and
convert USB Vbus control over to the regulators defined in DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Ludwig Zenz <lzenz@dh-electronics.com>
1. Introduce androidboot wrapper for booting AOSP.
2. Add partitions_android env var for simplifying the process of
writing new gpt table from U-boot shell/fastboot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
We never really added a sensible DFU configuration for platforms
based on eMMC. Most of the things one might want to do can also be done
with UMS or fastboot, so drop the DFU configuration.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Enable CONFIG_ARMV7_BOOT_SEC_DEFAULT by default to avoid a kernel
crash when booting NXP linux kernels in non-secure world,
when job ring device allocation is done by CAAM hw accelerator driver:
caam 30900000.caam: job rings = 3, qi = 0
caam_jr 30901000.jr0: failed to flush job ring 0
caam_jr: probe of 30901000.jr0 failed with error -5
caam_jr 30902000.jr1: failed to flush job ring 1
caam_jr: probe of 30902000.jr1 failed with error -5
caam_jr 30903000.jr2: failed to flush job ring 2
caam_jr: probe of 30903000.jr2 failed with error -5
caam algorithms registered in /proc/crypto
Job Ring Device allocation for transform failed
caam 30900000.caam: caam pkc algorithms registered in /proc/crypto
Unable to handle kernel NULL pointer dereference at virtual address 00000010
pgd = c0004000
[00000010] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Tainted:
Hardware name: Freescale i.MX7 Dual (Device Tree)
task: ec0d8000 task.stack: ec0ce000
PC is at caam_sm_startup+0x3f8/0x4f4
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Porting more DTS code from Linux kernel for display5 board required
increase of pre-relocation malloc pool size in U-Boot proper.
The early malloc memory is necessary for handling parsing and setup of
e.g. serial port device (and all its ancestors in DT tree).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
SPL on Engicam i.Core M6 boards enabled DM, so it would require some
malloc() pool before relocation in order to load U-Boot proper properly.
So, enable SPL malloc() pool of 0x2000 size similarly like what we have
used for icore mmc defconfigs.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
This commit enables CONFIG_OF_LIBFDT_OVERLAY a requirement to perform a
merge of an OPTEE provided DTB overlay into our main kernel DTB image.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
In order to switch on DTB overlay support in WaRP7 BL33 we first need to
switch on LIBFDT support. Do that now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
This patch switches on FIT verification of boot.scr. After this commit your
boot.scr must be in the FIT format.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
When booting in BL33 mode i.e. with u-boot loaded by OP-TEE we get the
following print-out.
Board: WARP7 in secure mode OPTEE DRAM 0xa0000000-0xa0000000
This is incorrect the right range is 0x9e000000-0xa0000000. This patch
fixes the defines on the warp7_bl33_defconfig file to tidy up the output.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
With the spl code correctly returning either MMC1 or MMC2,
this board can not boot either from internal eMMC (MMC1) or
the uSD card on the baseboard (MMC2) using the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch extends SiFive FU540 board support to setup ethaddr
env variable based on board serialnum read from OTP.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable USB3 support via the dwc3 XHCI driver.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
As the Rock960 doesn't have an onboard wired ethernet interface
it's useful to have some common USB wired ethernet devices added
to enable testing.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Enable the SDMA controller so the eMMC connected to the SDHCI
controller (sdhci@fe330000) can make use of it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
We have both PMIC and Regulator functionality so it's useful to
be able to see output and debug with the commands enabled.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The Rock960 doesn't contain SPI flash so drop related config options.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
Removed one of the defconfig(obsoleted) file
and unused CONFIG_MMC_SPI definition to avoid confusion
about if this board using non-DM stuff or not.
uCP1020 is completely DM free board, tested and runs well.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tests in test/py/tests/test_env.py like this fail without CONFIG_HUSH_PARSER:
=> => printenv test_env_0
## Error: "test_env_0" not defined
=> .=> setenv test_env_0
=> => echo $test_env_0
$test_env_0
=> F
We also want a mac address so the ethernet device works in qemu.
Signed-off-by: Joel Stanley <joel@jms.id.au>
The aspeed board does not have an upstream MMC driver.
As CONFIG_MMC defaults on, the board would fail to build due to the
CONFIG_DM_MMC migration:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Change the defconfig to disable MMC until a driver is submitted.
Signed-off-by: Joel Stanley <joel@jms.id.au>
This will allow for downloading and applying overlays from an MMC/SD
boot media based on the overlay_files ENV variable containing a list
of overlay files.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This will allow for downloading and applying overlays from an MMC/SD
boot media based on the overlay_files ENV variable containing a list
of overlay files.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The malloc pool used before relocation is getting tight leading to
out of memory errors doing certain DM-related calls. Since we are
running the A53 SPL out of DDR let's just go ahead and bump its size
as used in U-Boot proper as well as SPL (via Kconfig default value)
from 8KB to 32KB.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
The malloc pool used before relocation is getting tight leading to
out of memory errors doing certain DM-related calls. Since we are
running the A53 SPL out of DDR let's just go ahead and bump its size
as used in U-Boot proper as well as SPL (via Kconfig default value)
from 8KB to 32KB.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable GPIO driver for PCA953X-compatible I2C-based I/O expander
which includes support for the TCA9554/PCA9554-type expander found
on the AM654 EVM base board.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Enable GPIO driver for PCA953X-compatible I2C-based I/O expander
which includes support for the TCA9554/PCA9554-type expander found
on the AM654 EVM base board.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable I2C via driver model as well as the associated set of U-Boot
commands to allow us interacting with various I2C slave devices.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Enable I2C via driver model as well as the associated set of U-Boot
commands to allow us interacting with various I2C slave devices.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable all the relevant configs that enables support for loading
sysfw via MMC.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Switch to using the full malloc scheme in post-relocation SPL to allow
better utilization of available memory for example by allowing memory
to get freed. Initially allocate a 16MB-sized region in DDR starting
at address 0x84000000 for this purpose.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Sync the sdhci0 node from kernel. This changes the compatible that is
required to be there in the driver. Change the same for the SD card node
which is not yet supported in kernel. This also syncs the main_pmx0 node
as a side effect.
Also change the name of the driver to match the compatible in kernel.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
So far USB was not enabled for the Allwinner H6 boards, as the PHY
driver was not ready and the clock gates were missing. Since this is now
fixed, let's add the PHY and the OHCI/EHCI drivers to the build, for
all existing H6 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the H6 DRAM driver only supports one kind of LPDDR3 DRAM.
Split the timing parameters for this LPDDR3 configuration into a
separate file, to allow selecting an alternative later at compile time
(as the sunxi-dw driver does).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.
Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2"
(sha1: cc4bddade114b696ab27c1a77cfc7040151306da)
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.
To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The USE_TINY_PRINTF symbol only changes things within SPL and TPL
builds, so make it depend on that support. Next, make it default as
within these cases we should rarely have need of more advanced print
formats outside of the debug context.
To do this, in a few cases we need to correct our Kconfig dependencies
as we had cases of non-SPL targets select'ing this symbol. Finally, in
the case of a few boards we really do need the full printf
functionality.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI
and SPI_FLASH are converted.
The device tree contains only the minimal nodes required by U-Boot
since the size of U-Boot is limited to 256K on this device.
Signed-off-by: David Lechner <david@lechnology.com>
This addresses the following warning message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be
readily adapted. There is some additional 'gpio-hog' support
needed to fully setup USB in a similar manner to Linux.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Add support of Trusted boot chain with OP-TEE
- reserved 32MB at the end of the DDR for OP-TEE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Deactivate WATCHDOG by default in u-boot to avoid issue to boot kernel
and rootfs without the needed daemon to reload it.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
- SPL SATA enhancements to allow booting from RAW SATA device
needed for Clearfog (Baruch)
- Enable SATA booting on Clearfog (Baruch)
- Misc changes to Turris Omnia (Marek)
- Enable CMD_BOOTZ and increase SYS_BOOTM_LEN on crs305-1g-4s
(Luka)
- Enable FIT support for db-xc3-24g4xg (Chris)
- Enable DM_SPI on Keymile Kirkwood board with necessary changes
for this (Pascal)
- Set 38x and 39x AVS on lower frequency (Baruch)
- import DT updates from Linux
- add UniPhier SPI controller driver
- make U-Boot image for 64bit SoCs position independent
- tidy up various init code for next generation SoCs
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=X9wS
-----END PGP SIGNATURE-----
Merge tag 'uniphier-v2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2019.10
- import DT updates from Linux
- add UniPhier SPI controller driver
- make U-Boot image for 64bit SoCs position independent
- tidy up various init code for next generation SoCs
- misc cleanups
The name CONFIG_LEGACY_IMAGE_FORMAT reads slightly better along with
allowing us to avoid a rather nasty Kbuild/Kconfig issue down the line
with CONFIG_IS_ENABLED(IMAGE_FORMAT_LEGACY). In a few places outside of
cmd/ switch to using CONFIG_IS_ENABLED() to test what is set.
Signed-off-by: Tom Rini <trini@konsulko.com>
The corresponding configurations are selected in the common Kconfig file.
This is easier than changing every affected board default configuration
file. The default configuration for the PORTL2 board, however, still needs
some modifications to correctly use the driver model.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This change enables CMD_BOOTZ and increases SYS_BOOTM_LEN to
make it easier to work with kernel images.
Signed-off-by: Luka Kovacic <me@lukakovacic.xyz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
For a planned new SoC in this SoC family, the base address of the
DRAM will be changed from 0x80000000 to 0x20000000.
The PIE support will be useful to maintain multiple similar SoCs
whose DRAM addresses differ.
Now CONFIG_SYS_TEXT_BASE is not important. I just set it to 0
to ensure CONFIG_POSITION_INDEPENDENT is working.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdJEZEAAoJEB6zHgIOrC/I+LAH/jUDQpF5I68h0ZFGm3xoyGhm
3CSv8viOm/kL+GLubjnv4cwAp8N8VRpeJekz0Jt1Xp8C6OIgtnJ2Fln72KD+Z0IC
Rq7ByRS16iq4b6IUDRZObE4Jzxmf7rXU3jr0+/vd/en7kxVlvA9+Gsffs3OTGxC7
z9PysRZPBMH/smIPXdEQxYifnbpDG4fmfGcUWKrYfkB0Kq6Ep98Ia/gXNCY8XJ/A
sbNQGjJWJZWXS/TDetcC2VikssJ+yNFF34uzV+HD5Y3DW6ywLhuoDOz1pg8RR36i
YjcTCQz8lL/UVaUzrGUgPVAC3gdKY6J26GtV3vZavxBcmtGf0FhVtXO/tZc9AsY=
=6G45
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features and fixes for 2019.10 cycle
This includes the Atmel QSPI driver and support for the at91 boards.
This is the port of the driver from Linux, mostly done by Tudor Ambarus.
Add the default config file of QSPI media. The config is based on
sama5d27_som1_ek_mmc_defconfig.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add the default config file of QSPI media. The config is based on
sama5d2_xplained_mmc_defconfig.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
We use a sst spi-nor flash memory on sama5d27_som1_ek. Select
the others for testing purposes.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
We have a macronix spi-nor flash on sama5d2_xplained RevB and
a sst spi-nor flash on RevC. Select the rest for testing purposes.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Migrate the ubispl configuration for the omap3_igep00x0 and
am335x_igep003x boards to KConfig. Both boards were built with
SOURCE_DATE_EPOCH=0 and found to be equal before and after.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Javier Martínez Canillas <javier@dowhile0.org>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Enable the extended ENV options for AT91 and OMAP2PLUS in order to be
able to use CONFIG_ENV_UBI_* on these architectures.
As this change also makes the configs ENV_SIZE, ENV_SECT_SIZE,
ENV_OFFSET visible to AT91 and OMAP2PLUS, migrate users of these to
KConfig.
This migration was run using an extended moveconfig.py which evaluates
expressions such as "(512 << 10)". See patch ("moveconfig: expand
simple expressions").
All modified boards were built with SOURCE_DATE_EPOCH=0 before and
after the change and successfully confirmed that the identical binary
is generated (the only exception was igep00x0, which does not define
CONFIG_ENV_IS_IN_UBI in the original board header. Once that is
defined, the test passes too).
hs: rebased patch to:
68b90e57bc: "configs: tinker-rk3288 disable CONFIG_SPL_I2C_SUPPORT"
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Tom Rini <trini@konsulko.com>
Introduce the KConfig option CONFIG_ENV_UBI_VOLUME_REDUND for defining
the name of the UBI volume used to store the redundant environment.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
hs: get rid of stm32mp1* build errors
After the transition to DM, only the mx6dl/solo wandboard
is supported.
Add FIT image support so that all the wandboard variants
can be supported, like it was prior to the DM conversion.
Successfully booted Linux on mx6q/solo/qp wandboards.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
We need to update TEXT BASE for TPL/SPL/U-Boot;
SPL no need relocate STACK after enable TPL, so remove it;
Don't enable pinctrl names so that SPL can get pinctrl dts;
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
There is a regression seen on Poplar platform, which doesn't even show
a U-Boot version banner on booting. It turns out that due to landing
of commit 3a7c45f6a7 ("simple-bus: add DM_FLAG_PRE_RELOC flag to
simple-bus driver"), we need to increase SYS_MALLOC_F_LEN from its
default size 0x400, as pre-relocation requires more memory there. Let's
increase SYS_MALLOC_F_LEN to 0x4000 to fix the regression.
Thanks to Andreas Färber <afaerber@suse.de> for reporting, and Bin Meng
<bmeng.cn@gmail.com> for trouble shooting.
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Enable DM Video support on iMX53 M53Menlo and fix minor details
to restore previous behavior of the system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM block and DM MMC and DM USB support on iMX53 M53Menlo .
Convert board code to match the DM support. This also enables DM
pincontrol to configure the SDHI pins.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
