The TI DP83867 phy has been replaced with the MaxLinear GPY111 phy
due to part availability. Add support for it:
- increase post-reset time to 300ms per datasheet
- add tx-delay/rx-delay config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add gpio hog support for board-specific gpio lines:
- put hogs in u-boot.dtsi so as to keep the regular dts files
in sync with the kernel. The hogs will not be put in the kernel
as that makes them un-usable by userspace as well as
re-initializes them to dt defaults overriding changes which may
have been done by bootloader commands.
- specify gpio names and initial config
- enable GPIO_HOG
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- rename gsc{.c,.h} to eeprom{.c.h} for clarity
- collapse eeprom_get_dev
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable USB support for host controller and various USB ethernet
devices.
Example usage of USB Mass Storage (UMS) support:
u-boot=> mmc list
FSL_SDHC: 0
FSL_SDHC: 1
FSL_SDHC: 2 (eMMC)
u-boot=> ums 0 mmc 2
UMS: LUN 0, dev mmc 2, hwpart 0, sector 0x0, count 0xe30000
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use PREBOOT as well. This allows a customer to just set fdt_board as
on any other module to customize the device tree for his carrier
board.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop optional support for the ancient Apalis iMX6 V1.0 hardware which
had the UART wired as DCE rather than DTE.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This fixes the following crash when run on a Colibri iMX7S aka solo:
Colibri iMX7 # usb start
starting USB...
Bus usb@30b10000: USB EHCI 1.00
Bus usb@30b20000:
The i.MX 7Solo has only one single USB OTG1 but no USB host port. Trying
to initialize the nonexisting port just crashes.
While at it also drop board_usb_phy_mode() which is also no longer used
in the driver model age.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In case a customer wants to set fdtfile currently preboot overrides it
always with preboot just before the bootdelay. Use test -n to check
if fdtfile is already set and only set it if nothing got touched manually
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
For recovery purpose allow booting via SDP over USB as well.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add missing support of FIT-images and enable a verbosity for
this feature.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop legacy nfsboot script in favor of distroboot DHCP boot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Use the same name of DHCP Distroboot script as in regular eMMC case.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As video support is very specific depending on the exact display
customisation we decided to disable video support for all out modules
by default.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add DT bindings for a subset of GPCv2 which handles USB and PCIe PDs,
HSIOMIX PD controller and missing USB PD properties. This is required
to bring up the DWC3 USB controller up.
This is based on linux next and patches which are still pending
review, but which are likely going to be part of Linux 5.19:
b2d67d7bdf74 ("arm64: dts: imx8mp: disable usb3_phy1")
290918c72a29 ("arm64: dts: imx8mp: Add memory for USB3 glue layer to usb3 nodes")
https://www.spinics.net/lists/arm-kernel/msg958501.html
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The i.MX8MP glue needs to be configured based on a couple of DT
properties, implement .glue_configure callback to parse those DT
properties and configure the glue accordingly.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Rename the select_dr_mode callback to glue_configure, the callback is
used for more than enforcing controller mode even on the TI chips, so
change the name to a more generic one. No functional change.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add trivial driver for i.MX8MP HSIOMIX handling. This is responsible
for enabling the GPCv2 power domains and clock for USB 3.0 and PCIe
in the correct order. Currently supported is the USB 3.0 part which
can be tested, PCIe support should be easy to add.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX8MP power domain handling into the driver. This is based on the
Linux GPCv2 driver state which is soon to be in Linux next.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement power_domain_get_by_name() convenience function which parses
DT property 'power-domain-names' and looks up power domain by matching
name.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
This driver is the only SMCCC dependency in iMX8M U-Boot port. Rework
the driver based on Linux GPCv2 driver to directly control the GPCv2
block instead of using SMCCC calls. This way, U-Boot can operate the
i.MX8M power domains without depending on anything else.
This is losely based on Linux GPCv2 driver. The GPU, VPU, MIPI power
domains are not supported to save space, since they are not useful in
the bootloader. The only domains kept are ones for HSIO, PCIe, USB.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The arch/arm/include/asm/arch-imx8m/power-domain.h is not included
anywhere except in drivers/power/domain/imx8m-power-domain.c, just
inline the content and drop the header. No functional change.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
In case the power domain node structure is gpc@303a0000/pgc/power-domain@N,
do not bind power domain driver to the 'pgc' node, but rather descend into
it and only bind power domain drivers to power-domain@N subnodes. This way
we do not waste one useless driver instance associated with 'pgc' node.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
In case the ops is not implemented, return 0 in the core right away.
This is better than having multiple copies of functions which just
return 0 in each power domain driver. Drop all those empty functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
The div loop uses reassign and reuse parent_rate, which causes
the parent rate reference to be wrong after the first loop, the
resulting clock becomes incorrect for div != 1.
Fixes: 829e06bf41 ("imx8ulp: clock: Add MIPI DSI clock and DCNano clock")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
- Two TI K3 updates, update SYS_MALLOC_F_LEN default to be 0x2000 and
move TI am33xx to use that as well, fix DT relocation with multiple
DRAM banks, and add a gpio read sub-command.
As explained in commit 4af2a33ee5 ("cmd: gpio: Make `gpio input`
return pin value again") the `gpio input` is used in scripts to obtain
the value of a pin, despite the fact that CMD_RET_FAILURE is
indistinguishable from a valid pin value.
To be able to detect failures and properly use the value of a GPIO in
scripts we introduce the `gpio read` command that sets the variable
`name` to the value of the pin. Return code of the `gpio read` command
can be used to check for CMD_RET_SUCCESS or CMD_RET_FAILURE.
CONFIG_CMD_GPIO_READ is used to enable the `gpio read` command.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Allow device tree to provide ti,ddr-freq0 to be used as the initial DDR
frequency that is set for lpddr4 before initialization of the
controller. Make this optional and continue to use PLL bypass frequency
as is done currently if ti,ddr-freq0 is not provided.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The current implementation of boot_relocate_fdt() places DT at the
highest usable DRAM address, which is calculated as:
env_get_bootm_low() + env_get_bootm_mapsize()
which by default becomes gd->ram_base + gd->ram_size.
Systems like i.MX53 can have multiple DRAM banks with gap between them,
e.g. have DRAM at 0x70000000-0x8fffffff and 0xb0000000-0xcfffffff , so
for them the calculated highest DRAM address is 0xafffffff, which is
exactly in the gap and thus not usable.
Fix this by iterating over all DRAM banks and tracking the remaining
amount of the total mapping size obtained from env_get_bootm_mapsize().
Limit the maximum LMB area size to each bank, to avoid using nonexistent
DRAM.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The k3-ddrss driver wants to configure the DDRSS_V2A_CTL_REG to reflect
the maximum possible SDRAM of 2 GB for AM64x (instead of the register's
default that says 8 GB, which the AM64x DDR controller wouldn't support).
The offset 0x20 was correct, but the register name DDRSS_V2A_R1_MAT_REG
was that of the next register at offset 0x24.
Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
- Migrate CONFIG_SYS_MEM_TOP_HIDE to Kconfig, IOMUX bugfix, 2 BTRFS
bugfixes, update .gitignore and .mailmap files, aspeed GPIO bugfix,
image-fit and squashfs code cleanups, enable EXT4 and ISO partitions on
DeveloperBox.
- populate u-boot,bootconf under /chosen, see
https://github.com/devicetree-org/dt-schema/pull/71 for corresponding
change
Currently there is no btrfs support in SPL. But macro CONFIG_FS_BTRFS is
defined also when building SPL. When both FS_BTRFS and SPL are enabled
then build process throw compile error.
Fix check for btrfs code in fstypes[] to allow compiling FS_BTRFS only in
proper U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fix following two compile errors on big endian systems:
CC fs/btrfs/btrfs.o
In file included from include/linux/byteorder/big_endian.h:107,
from ./arch/powerpc/include/asm/byteorder.h:82,
from ./arch/powerpc/include/asm/bitops.h:8,
from include/linux/bitops.h:152,
from include/uuid.h:9,
from fs/btrfs/btrfs.c:10:
fs/btrfs/conv-funcs.h: In function ‘btrfs_key_to_disk’:
include/linux/byteorder/generic.h:90:21: error: ‘__cpu_to_le16’ undeclared (first use in this function); did you mean ‘__cpu_to_le16p’?
#define cpu_to_le16 __cpu_to_le16
^~~~~~~~~~~~~
fs/btrfs/conv-funcs.h:79:10: note: in expansion of macro ‘cpu_to_le16’
__u16: cpu_to_le16, \
^~~~~~~~~~~
CC fs/btrfs/compression.o
In file included from ./arch/powerpc/include/asm/unaligned.h:9,
from fs/btrfs/compression.c:16:
include/linux/unaligned/access_ok.h:6:19: error: redefinition of ‘get_unaligned_le16’
static inline u16 get_unaligned_le16(const void *p)
^~~~~~~~~~~~~~~~~~
In file included from fs/btrfs/ctree.h:16,
from fs/btrfs/btrfs.h:12,
from fs/btrfs/compression.c:8:
include/linux/unaligned/le_byteshift.h:40:19: note: previous definition of ‘get_unaligned_le16’ was here
static inline u16 get_unaligned_le16(const void *p)
^~~~~~~~~~~~~~~~~~
Include file asm/unaligned.h contains arch specific macros and functions
for unaligned access as opposite to linux/unaligned le_byteshift.h which
contains macros and functions specific to little endian systems only.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Qu Wenruo <wqu@suse.com>
We should only access console_devices[file][i] once we have checked that i
< cd_count[file]. Otherwise, we will access uninitialized memory at the end
of the loop. console_devices[file][i] should not be NULL, but putting the
assignment in the loop condition allows us to ensure that i is checked
beforehand. This isn't a bug, but it does make valgrind stop complaining.
Fixes: 400797cad3 ("IOMUX: Split out for_each_console_dev() helper macro")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Andrew Scull <ascull@google.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* free() checks if its argument is NULL. Remove duplicate checks.
* Remove duplicate free(ovcopy).
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The offset of the current read back register is the value of the gpio pin,
not the value written for the gpio output.
This patch fix it to avoid the other gpio output value controlled by the
same register being set incorrectly.
Fixes: 7ad889b0f3 ("gpio: Add Aspeed GPIO driver")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Since this box is SystemReady compliant enable ISO_PARTITION which is
needed to start some installers (e.g Fedora). While at it enable EXT4
as well which is a common filesystem for targets
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Xilinx has been acquired by AMD that's why emails should be also updated.
The patch is updating .mailmap file and also MAINTAINERS files as was done
by commit 5cd1ecb994 ("ppc: qemu: Update MAINTAINERS for correct email
address").
The rest of my emails are not going to change.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
It can be useful for the OS (Linux) to know which configuration has
been chosen by U-Boot when launching a FIT image.
Store the name of the FIT configuration node used in a new string
property called 'u-boot,bootconf' in the '/chosen' node in device tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
