Commit graph

47933 commits

Author SHA1 Message Date
Vignesh R
96907c0fe5 dm: spi: Read default speed and mode values from DT
In case of DT boot, don't read default speed and mode for SPI from
CONFIG_*, instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:34 +05:30
Vignesh R
e835a74159 ARM: dts: dra7x: Support QSPI MODE-0 operation at 64MHz
According to Data Manual(SPRS915P) of AM57x, TI QSPI controller on
DRA74(rev 1.1+)/DRA72 EVM can support up to 64MHz in MODE-0, whereas
MODE-3 is limited to 48MHz. Hence, switch to MODE-0 for better
throughput.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:33 +05:30
Vignesh R
988fb5ce61 defconfig: k2g_evm_defconfig: Enable Cadence QSPI controller
Enable Cadence QSPI controller support to use QSPI on K2G SoC. Also
enable Spansion flash support to access s25fl512s flash present on K2G
QSPI bus.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:33 +05:30
Vignesh R
b60774fff1 ARM: dts: K2G: Add support for QSPI controller
K2G SoC has a Cadence QSPI controller to communicate with NOR flash
devices. Add DT nodes to support the same.
Also, K2G EVM has a s25fl512s flash connect to QSPI bus at CS 0. Add nor
flash slave node for the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:33 +05:30
Vignesh R
2372e14f19 spi: cadence_quadspi: Enable QUAD mode based on DT data
Instead of relying on CONFIG_SPI_FLASH_QUAD to be defined to enable QUAD
mode, make use of mode_rx field of dm_spi_slave_platdata to determine
whether to enable or disable QUAD mode. This is necessary to support
muliple SPI controllers where one of them may not support QUAD mode.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:33 +05:30
Vignesh R
dac3bf20fb spi: cadence_qspi_apb: Support 32 bit AHB address
AHB address can be as long as 32 bit, hence remove the
CQSPI_REG_INDIRECTRDSTARTADDR mask. Since AHB address is passed from DT
and read as u32 value, it anyway does not make sense to mask upper bits.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:32 +05:30
Vignesh R
fdf02a36c5 defconfig: k2g_evm_defconfig: enable SPI driver model
Enable SPI and SPI Flash driver model as K2G SPI controller driver
supports driver model.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:32 +05:30
Vignesh R
c8e750473a ARM: dts: k2g: add support for Davinci SPI controller
K2G SoC has 4 SPI instances that are compatible with davinci_spi
controller(present on previous generation of Keystone2 devices). Add DT
nodes for the same. K2G EVM has a N25Q128A13 SPI NOR flash connected on
SPI-1. Add DT bindings for the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:32 +05:30
Vignesh R
c48f879c38 defconfig: k2l_evm_defconfig: enable SPI driver model
Enable SPI and SPI Flash driver model as K2L SPI controller driver
supports driver model.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:32 +05:30
Vignesh R
188179481d ARM: dts: k2l: Enable Davinci SPI controller
Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:32 +05:30
Vignesh R
cf4f0a9afc defconfig: k2e_evm_defconfig: enable SPI driver model
Enable SPI and SPI Flash driver model as K2E SPI controller driver
supports driver model.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:31 +05:30
Vignesh R
2655f1625a ARM: dts: k2e: Enable Davinci SPI controller
Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:31 +05:30
Vignesh R
376c533b89 defconfig: k2hk_evm_defconfig: enable SPI driver model
Enable SPI and SPI Flash driver model as K2HK SPI controller driver
supports driver model.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:31 +05:30
Vignesh R
96368e6e38 ARM: dts: k2hk: Enable Davinci SPI controller
Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:31 +05:30
Vignesh R
e5fcf0372b ARM: dts: keystone2: add SPI aliases for davinci SPI nodes
Add aliases for SPI nodes in order for it to be probed by the DM
framework.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:31 +05:30
Vignesh R
3983224423 keystone2: spi: do not define DM_SPI and DM_SPI_FLASH for SPL build
Since Keystone2 devices do not have support DM in SPL, do not define
DM_SPI and DM_SPI_FLASH for SPL build.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:30 +05:30
Vignesh R
192bb756dc spi: davinci_spi: Convert to driver to adapt to DM
Convert davinci_spi driver so that it complies with SPI DM framework.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:30 +05:30
Vignesh R
7c61686255 dm: core: implement dev_map_physmem()
This API helps to map physical register addresss pace of device to
virtual address space easily. Its just a wrapper around map_physmem()
with MAP_NOCACHE flag.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:08 +05:30
Mingkai Hu
d73718f323 armv8: Enable CPUECTLR.SMPEN for coherency
For A53, data coherency is enabled only when the CPUECTLR.SMPEN bit is
set. The SMPEN bit should be set before enabling the data cache.
If not enabled, the cache is not coherent with other cores and
data corruption could occur.

For A57/A72, SMPEN bit enables the processor to receive instruction
cache and TLB maintenance operations broadcast from other processors
in the cluster. This bit should be set before enabling the caches and
MMU, or performing any cache and TLB maintenance operations.

Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-08 17:16:49 -04:00
Daniel Schwierzeck
d56dd0b1f8 test/py: support 'memstart =' in u_boot_utils.find_ram_base()
Some archs like MIPS or PPC have a different 'bdinfo' output
than ARM regarding the memory configuration. Also support
'memstart = 0x*' in u_boot_utils.find_ram_base() to make
all tests requiring the RAM base working on those archs.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
2016-07-08 17:16:45 -04:00
Stephen Warren
085e64dd42 test/py: strip VT100 codes from match buffer
Prior to this patch, any VT100 codes emitted by U-Boot are considered part
of a command's output, which often causes tests to fail. For example,
test_env_echo_exists executes printenv, and then considers any text on a
line before an = sign as a valid U-Boot environment variable name. This
includes any VT100 codes emitted. When the test later attempts to use that
variable, the name would be invalid since it includes the VT100 codes.
Solve this by stripping VT100 codes from the match buffer, so they are
never seen by higher level test code.

The codes are still logged unmodified, so that users can expect U-Boot's
exact output without interference. This does clutter the log file a bit.
However, it allows users to see exactly what U-Boot emitted rather than a
modified version, which hopefully is better for debugging. It's also much
simpler to implement, since logging happens as soon as text is received,
and so stripping the VT100 codes from the log would require handling
reception and stripping of partial VT100 codes.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2016-07-08 17:16:42 -04:00
Alexander Graf
0de02de768 arm: Fix setjmp (again)
Commit e677724 (arm: Fix setjmp) added code to fix compilation of the setjmp
code path with thumv1. Unfortunately it missed a constraint that the adr
instruction can only refer to 4 byte aligned offsets.

So this patch adds the required alignment hooks to make compilation
work again even when setjmp doesn't happen to be 4 byte aligned.

Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Tom Rini <trini@konsulko.com>
2016-07-08 17:16:38 -04:00
Yoshinori Sato
747431b9d5 serial_sh: Add standrad SCI (w/o FIFO) support
Add support for standard type SCI (without FIFO) port.

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2016-07-09 05:51:57 +09:00
Yoshinori Sato
359787cfe4 serial_sh: Device Tree support
Add Device Tree bindings.

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2016-07-09 05:51:57 +09:00
Andre Przywara
59d07ee08e SPL: tiny-printf: avoid any BSS usage
As printf calls may be executed quite early, we should avoid using any
BSS stored variables, since some boards put BSS in DRAM, which may not
have been initialised yet.
Explicitly mark those "static global" variables as belonging to the
.data section, to keep tiny-printf clear of any BSS usage.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2016-07-08 12:50:34 -04:00
Stephen Warren
a82642f398 test/py: fix CONFIG_ tests
Some CONFIG_ variables were recently renamed, but test/py wasn't updated
to match. This causes some tests to be skipped. Fix test/py so the tests
are run.

Fixes: 1163625898 ("Rename reset to sysreset")
Fixes: f1f9d4fac5 ("hush: complete renaming CONFIG_SYS_HUSH_PARSER to CONFIG_HUSH_PARSER")
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2016-07-08 12:47:58 -04:00
Mateusz Kulikowski
eb9d3ca356 mmc: msm_sdhci: Set mmc->dev pointer in msm_sdc_probe()
MMC core expects (now) valid mmc->dev pointer.
During conversion in commit cffe5d86 not every driver was updated.

This patch fixes crash while accessing MMC on
boards using Qualcomm SDHCI controller.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-08 09:57:30 -04:00
Tom Rini
abbaa23f65 Merge branch 'master' of git://git.denx.de/u-boot-usb 2016-07-07 09:58:41 -04:00
York Sun
eb364c3dc2 powerpc: mpc85xx: kmp204x: Fix compiling error for usb errata
Commit 9262367 moves USB errata workaround into a C file. This
causes compiling error for kmcoge4 and kmlion1. To enable the
errata workaround, define CONFIG_USB_EHCI_FSL in common header.

Signed-off-by: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ed Swarthout <Ed.Swarthout@nxp.com>
Cc: Sriram Dash <sriram.dash@nxp.com>
Fixes: 92623672f9 ("fsl: usb: make errata function common for PPC and ARM")
2016-07-07 13:34:10 +02:00
Tom Rini
99b8275797 Merge branch 'master' of git://git.denx.de/u-boot-tegra 2016-07-06 15:55:36 -04:00
Tom Rini
246fa47840 Merge branch 'master' of git://git.denx.de/u-boot-net 2016-07-06 15:55:21 -04:00
Oleksandr Tymoshenko
4c64c4db3b net: rtl8169: Fix return value for rtl_send_common
Return value of rtl_send_common propogates unmodified all the way
up to eth_send and further to API consumer if CONFIG_API is enabled.
Previously rtl_send_common returned number of bytes sent on success
which was erroneouly detected as error condition by API consumers
that checked for operation success by comparing return value with 0.

Switch rtl_send_common to use common convention: return 0 on success
and negative value for failure.

Cc: Stephen Warren <swarren@nvidia.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-06 10:45:11 -05:00
Ralf Hubert
e4ead4a21d net: Fix incorrect RPC packets on 64-bit systems
This patch fixes incorrect RPC packet layout caused by
'long' type size difference on 64 and 32-bit architectures.

Signed-off-by: Ralf Hubert <r.hubert@technisat.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-06 10:45:07 -05:00
Mingkai Hu
19c9ddaa4f driver: net: phylib: add support for aquantia AQR106/107 PHY
This patch adds support for aquantia AQR106/107 PHY.

Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-06 10:45:04 -05:00
Alexey Brodkin
66d027e22c net: designware: Make driver independent from DM_GPIO again
Commit 90b7fc924a "net: designware: support phy reset device-tree
bindings" made DW GMAC driver dependent on DM_GPIO by unconditional
usage of purely DM_GPIO stuff like:
 * dm_gpio_XXX()
 * gpio_request_by_name()

But since that driver as of today might be easily used without
DM_GPIO (that's the case for Synopsys AXS10x boards) we're
shielding all DM_GPIO things by ifdefs.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-06 10:45:00 -05:00
Joe Hershberger
2307ea4053 common: Always include errno.h in common.h
We want people using errnos for errors instead of -1, so make it easy
by always including the definition of all the errnos.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-07-06 10:44:56 -05:00
Anatolij Gustschin
c8864d7209 spi: spi-uclass: fix typo in debug output
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-06 12:40:32 +05:30
Simon Glass
703aaf76c2 fdt: Drop some unused compatible strings
We have driver-model drivers for some of these now, so drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05 13:23:04 -07:00
Simon Glass
8d37483e7c tegra: video: Always use write-through cache on LCD
This seems to give the best performance, so let's use it always.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05 13:19:08 -07:00
Simon Glass
ec5507707a video: tegra: Move to using simple-panel and pwm-backlight
We have standard drivers for panels and backlights which can do most of the
work for us. Move the tegra20 LCD driver over to use those instead of custom
code.

This patch includes device tree changes for the nvidia boards. I have only
been able to test seaboard. If this patch is applied, these boards will
also need to be synced with the kernel, and updated to use display-timings:

   - colibri
   - medcom-wide
   - paz00
   - tec

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05 13:19:08 -07:00
Simon Glass
ce02a71c23 tegra: dts: Sync tegra20 device tree files with Linux
Sync everything except the display panel, which will come in a future patch.
One USB port is left disabled since we don't want to support it in U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05 13:19:08 -07:00
Simon Glass
862887d883 errno: Allow errno_str() to be used without CONFIG_ERRNO_STR
The pmic framework uses errno_str() and this requires board that use it to
enable CONFIG_ERRNO_STR to avoid a build error. Update the header to provide
a NULL error message when CONFIG_ERRNO_STR is not defined, and fix the build
error.

This will show as "(null)" when U-Boot prints it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05 13:19:08 -07:00
Simon Glass
00e9e6d1ff errno: Add copyright header and header guard
Bring in a copyright for this file from cmd/pmic.c since this file was
submitted by the same author at around the same time. Also fix the missing
header guard.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05 13:19:08 -07:00
Stephen Warren
f39a6a3277 pci: tegra: actually program REFCLK_CFG* on recent SoCs
On recent SoCs, tegra_pcie_phy_enable() isn't called; but instead
tegra_pcie_enable_controller() calls tegra_xusb_phy_enable(). However,
part of tegra_pcie_phy_enable() needs to happen in all cases. Move that
code to tegra_pcie_port_enable() instead.

For reference, NVIDIA's downstream Linux kernel performs this operation
in tegra_pcie_enable_rp_features(), which is called immediately after
tegra_pcie_port_enable(). Since that function doesn't exist in the U-Boot
driver, we'll just add it to the tail of tegra_pcie_port_enable() instead.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05 11:14:32 -07:00
Stephen Warren
3cfc6be4a8 pci: tegra: correctly program PADS_REFCLK registers
The value that should be programmed into the PADS_REFCLK register varies
per SoC. Fix the Tegra PCIe driver to program the correct values. Future
SoCs will require different values in cfg0/1, so the two values are stored
separately in the per-SoC data structures.

For reference, the values are all documented in NV bug 1771116 comment 20.
The Tegra210 value doesn't match the current TRM, but I've filed a bug to
get the TRM fixed. Earlier TRMs don't document the value this register
should contain, but the ASIC team has validated all these values, except
for the Tegra20 value which is simply left unchanged in this patch.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05 11:14:32 -07:00
Sjoerd Simons
70c440e5bd rockchip: video: Lower hpd wait time
Waiting 30 seconds for the hpd to go high seems a bit much, especially
on headless boots. Lowering the timeout to 300ms.

Sending as RFC because frankly i don't know what a sensible timeout is
here, but 30 seconds is clearly not it :)

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Dropped RFC tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-05 10:38:56 -06:00
Marek Vasut
12c67d7522 powerpc: mpc85xx: Do not build errata command in SPL
The errata command is useless in SPL, so don't build it. This fixes
multiple build failures on PowerPC.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: York Sun <york.sun@nxp.com>
Fixes: 92623672f9 ("fsl: usb: make errata function common for PPC and ARM")
2016-07-05 17:40:28 +02:00
Hans de Goede
e6e188f562 usb: dm: Make "usb info" use usb_for_each_root_dev()
The old dm "usb info" implementation has several issues:

1) NULL pointer deref when a bus has no children
2) Not showing usb devices on busses without an emulated root-hub (otg host)
3) Attempting to show devices on inactive busses
4) "usb info" Would cause some hosts to get re-probed something which only
   "usb reset" should do

TL;DR: proper iterating over usb bus root devs is hard, use the helper
for it.

Reported-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-05 14:14:11 +02:00
Hans de Goede
2138fd6d5d usb: dm: Add a usb_for_each_root_dev() helper function
Iterating over usb-root devs and doing something for all of them is
a bit tricky with dm, factor out the proven usb_show_tree() for this
into a helper function.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-05 14:14:11 +02:00
Tom Rini
e8009beff6 Merge git://git.denx.de/u-boot-arc 2016-07-04 11:46:21 -04:00