Commit graph

91 commits

Author SHA1 Message Date
Oleksandr Suvorov
99dd2549a1 GPIO: fxl6408: Add support for FXL6408 GPIO expander
Initial support for Fairchild's 8 bit I2C gpio expander FXL6408.
The CONFIG_FXL6408_GPIO define enables support for such devices.

Based on: https://patchwork.kernel.org/patch/9148419/

Signed-off-by: Oleksandr Suvorov <cryosay@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
2022-02-05 13:38:39 +01:00
Tom Rini
068415eade Xilinx changes for v2022.04-rc1
gpio:
 - Add modepin driver
 
 net:
 - Save random mac addresses to eth variable
 
 zynqmp gem:
 - Add support for mdio bus DT description
 - Add support for reset and SGMII phy configuration
 - Reduce timeout for MDIO accesses
 
 zynqmp clk:
 - Fix clock handling for gem and usb
 
 phy:
 - Add zynqmp phy/serdes driver
 
 serial:
 - Add one missing compatible string
 
 microblaze:
 - Symbol alignement
 - SPL fixups
 - Code cleanups
 
 zynqmp:
 - Various dt changes, DP pre-reloc, gem resets, gem clocks
 - Switch SOM to shared psu configuration
 - Move dcache handling to firmware driver
 - Workaround gmii2rgmii DT description issue
 - Enable broadcasts again
 - Change firmware enablement logic
 - Small adjustement in firmware driver
 
 versal:
 - Support new mmc@ DT nodes
 - Fix run time variable handling
 - Add missing I2C_PMC ID for power domain
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
 IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
 =HtB+
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx changes for v2022.04-rc1

gpio:
- Add modepin driver

net:
- Save random mac addresses to eth variable

zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses

zynqmp clk:
- Fix clock handling for gem and usb

phy:
- Add zynqmp phy/serdes driver

serial:
- Add one missing compatible string

microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups

zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver

versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
2022-01-19 11:43:44 -05:00
T Karthik Reddy
3b441cf4e4 zynqmp: gpio: Add support for zynqmp gpio modepin driver
ZynqMP modepin driver has capability to get/set/check status of modepin
gpios. These modepins are accessed using xilinx firmware. In modepin
register, [3:0] bits set direction, [7:4] bits read IO, [11:8] bits
set/clear IO.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/2d802d98fd56d95d764532a33e844d935e0cebb3.1635505900.git.michal.simek@xilinx.com
2022-01-05 10:22:02 +01:00
Tom Rini
b2d1c828b9 Convert CONFIG_KIRKWOOD_GPIO to Kconfig
This converts the following to Kconfig:
   CONFIG_KIRKWOOD_GPIO

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27 16:20:19 -05:00
Hannes Schmelzer
bba76a17bd drivers/gpio: add support for MAX7320 i2c i/o expander
This commit adds support for the MAX7320 (and clones) gpio expander.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2021-10-19 11:25:24 -04:00
Tom Rini
6674edaabf Prepare v2021.10-rc4
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmFBKRgACgkQFHw5/5Y0
 tyw/PwwAtGB3rBeYW4rjWuMC5WP1UDTnvZIAok5ImWumWDahjDm8Yq2VCzAe9adw
 EYBjuNmaNl9aQvGVqlVJeIcLku5MLuLQu2za8vhc1R8X9VTPPY+LLTcdOokOmB8y
 8JiaE7fJsb1bZeV+diF9tss3B0IkUrwSJtW1d+qfdz/4UiRvwK5BhnZgzIobDldO
 g1Ldz/xiR2GOAXlUMwDrNAi6qNvmeAqRsQxySVrjltAV2ST7LJnOiHuWvJX6g6VS
 l796Hleh/kULfEW6n+1ZaTNqvVRcJ8xYSOG8w8y9u6HuPBA3JrYH1p1Eo5n7PPDv
 US71Iy/ncweTyfTMEBThWLqjHOQ05sVkWX/r4fj2iJRli+Og53lE1fVJ4ajIx7vz
 Tc76wI43i0I5lr2yTErjUG6EzDDoueqd+c8BwxihNLUK/+QG31xoCEMfC80C25ro
 QhYVFgiPWN0ySUD5M5tbGXODvfNNIDKXpY5oSOTVtemZtDEMpO2zBM1s/K3RV7Ud
 Je9Pj0Cu
 =Me42
 -----END PGP SIGNATURE-----

Merge tag 'v2021.10-rc4' into next

Prepare v2021.10-rc4

Signed-off-by: Tom Rini <trini@konsulko.com>

# gpg: Signature made Tue 14 Sep 2021 06:58:32 PM EDT
# gpg:                using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C
# gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate]

# Conflicts:
#	board/Arcturus/ucp1020/spl.c
#	cmd/mvebu/Kconfig
#	common/Kconfig.boot
#	common/image-fit.c
#	configs/UCP1020_defconfig
#	configs/sifive_unmatched_defconfig
#	drivers/pci/Kconfig
#	include/configs/UCP1020.h
#	include/configs/sifive-unmatched.h
#	lib/Makefile
#	scripts/config_whitelist.txt
2021-09-16 10:29:40 -04:00
Simon Glass
3232bdf0b3 pci: Drop DM_PCI
This option has not effect now. Drop it, using PCI instead where needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-13 18:23:13 -04:00
Simon Glass
b2f9bac0e7 gpio: Add a GPIO config
At present we have SPL_GPIO and TPL_GPIO but not piain GPIO. This
works because there is a special build rule in Makefile that always
includes the drivers/gpio directory.

It is better to have all driver directories included by drivers/Makefile
and there is already a rule in there for this purpose. It just needs a
Kconfig for U-Boot proper, so add one.

Enable the option always for now, since this mimics current behaviour.
This can be updated once DM_GPIO is used everywhere.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-04 12:26:02 -04:00
Michal Simek
b4c2c151b1 Kconfig: Remove all default n/no options
default n/no doesn't need to be specified. It is default option anyway.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-31 17:47:49 -04:00
Sebastian Reichel
0b3da993a4 gpio: mcp230xx: Introduce new driver
Introduce driver for I2C based MCP230xx GPIO chips, which are
quite common and already well supported by the Linux kernel.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-08-22 10:53:14 +02:00
Simon Glass
83061dbd1c Rename GPIO_SUPPORT to GPIO
Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-07-28 14:29:36 -04:00
Stephan Gerhold
1e0b4c07bf gpio: Add driver for Nomadik GPIO
Nomadik GPIO is a fairly simple GPIO module used in the ST-Ericsson
Ux500 SoCs (and some older Nomadik SoCs). It uses registers where
each GPIO is represented as a single bit, plus "set" and "clear"
registers that allow updating the state without having to read the
existing state.

The driver implements support for it for use together with DM_GPIO
and the existing ste-dbx5x0.dtsi device tree.

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-14 16:47:56 -04:00
Michal Simek
ca8bb0ccb7 gpio: pca953x: Add missing i2c dependency
pca953x also depends on i2c that's why add dependency to Kconfig.
Where GPIO is enabled but I2C compilation error pops up.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-06-23 09:48:35 +02:00
Harm Berntsen
98b64fe70b gpio: Add support for DM GPIO for Kirkwood
The Armada driver also works on Nedap's custom Kirkwood board with a
Marvell 88F6180 CPU. The original commit of that driver,
commit 704d9a645e ("gpio: Add DM GPIO driver for Marvell MVEBU"),
also mentions that this driver would be suitable for Kirkwood. This
does not completely replace the Kirkwood specific driver as there
are still boards depending on that driver.

Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Stefan Roese <sr@denx.de>,
Reviewed-by: Stefan Roese <sr@denx.de>
2021-01-27 07:25:39 +01:00
Weijie Gao
ca610ddf97 gpio: add GPIO controller driver for MediaTek MT7620 SoC
This patch adds GPIO controller driver for MediaTek MT7620 SoC

Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-24 21:39:26 +01:00
Michal Simek
664e16ce99 xilinx: kconfig: Change Kconfig dependencies for Xilinx drivers
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2020-08-20 09:46:55 +02:00
Suneel Garapati
f7331c65b8 gpio: octeon_gpio: Add GPIO controller driver for Octeon
Add support for GPIO controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.

Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2020-08-03 21:11:41 +02:00
Rayagonda Kokatanur
a7090b42af drivers: gpio: add broadcom iproc gpio driver support
Add gpio driver support for Broadcom iproc-based socs.

Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-29 10:37:11 -04:00
Stefan Bosch
b8f748d6f2 gpio: add nexell driver
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- livetree API (dev_read_...) is used instead of fdt one (fdt...).

Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
2020-07-29 08:43:40 -04:00
Heiko Schocher
2bd261dd17 gpio: search for gpio label if gpio is not found through bank name
dm_gpio_lookup_name() searches for a gpio through
the bank name. But we have also gpio labels, and it
makes sense to search for a gpio also in the labels
we have defined, if no gpio is found through the
bank name definition.

This is useful for example if you have a wp pin on
different gpios on different board versions.

If dm_gpio_lookup_name() searches also for the gpio labels,
you can give the gpio an unique label name and search
for this label, and do not need to differ between
board revisions.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Don't enable by default]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-07 18:23:37 -04:00
Tom Rini
348d183e54 Convert CONFIG_AT91_GPIO to Kconfig
This converts the following to Kconfig:
   CONFIG_AT91_GPIO

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-26 10:29:04 -04:00
Trevor Woerner
71f6354b0e rename symbol: CONFIG_STM32 -> CONFIG_ARCH_STM32
Have this symbol follow the pattern of all other such symbols.

Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2020-05-15 14:47:35 -04:00
Klaus H. Sorensen
3fb22bc2f8 gpio/mpc83xx_spisel_boot.c: gpio driver for SPISEL_BOOT signal
Some SoCs in the mpc83xx family, e.g. mpc8309, have a dedicated spi
chip select, SPISEL_BOOT, that is used by the boot code to boot from
flash.

This chip select will typically be used to select a SPI boot
flash. The SPISEL_BOOT signal is controlled by a single bit in the
SPI_CS register.

Implement a gpio driver for the spi chip select register. This allows a
spi driver capable of using gpios as chip select, to bind a chip select
to SPISEL_BOOT.

It may be a little odd to do this as a GPIO driver, since the signal
is neither GP or I, but it is quite convenient to present it to the
spi driver that way. The alternative it to teach mpc8xxx_spi to handle
the SPISEL_BOOT signal itself (that is how it's done in the linux
kernel, see commit 69b921acae8a)

Signed-off-by: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2020-03-31 10:06:52 -04:00
Jason Li
2ccacf3c7f gpio: cortina_gpio: add DM_GPIO driver for CAxxxx SoCs
DM_GPIO based GPIO controller driver for CAxxxx SoCs.
This driver support multiple CPU architectures and
Cortina Access SoC platforms.

Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
2020-02-07 14:01:21 -05:00
Philippe Reynes
17f34ca803 gpio: bcm6345: allow to use this driver on arm bcm68360
This IP is also used on some arm SoC, so we allow to
use it on arm bcm68360 too.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2020-01-23 07:29:58 -05:00
Simon Glass
7e589bc19b x86: Add a generic Intel GPIO driver
Add a GPIO driver which uses the pinctrl driver to access the pad
information. This driver relies on the GPIO nodes being subnodes to the
pinctrl device.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-12-15 11:44:25 +08:00
Simon Glass
bcee8d6764 dm: gpio: Allow control of GPIO uclass in SPL
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.

Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.

Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.

This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-12-15 08:52:29 +08:00
Ashok Reddy Soma
982485214f gpio: zynq: Add gpio driver support for Versal
This patch adds support for gpio driver for versal platform

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:01 +02:00
Sagar Shrikant Kadam
d26b40450b gpio: sifive: add support for DM based gpio driver for FU540-SoC
This patch adds a DM based driver model for gpio controller present in
FU540-C000 SoC on HiFive Unleashed A00 board. This SoC has one GPIO
bank and 16 GPIO lines in total, out of which GPIO0 to GPIO9 and
GPIO15 are routed to the J1 header on the board.

This implementation is ported from linux based gpio driver submitted
for review by Wesley W. Terpstra <wesley@sifive.com> and/or Atish Patra
<atish.patra@wdc.com> (many thanks !!). The linux driver can be referred
here [1]

[1]: https://lkml.org/lkml/2018/10/9/1103

Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-18 09:04:01 +08:00
Lukasz Majewski
5484793363 kconfig: Convert CONFIG_MXS_GPIO to Kconfig
This converts the following to Kconfig:
   CONFIG_MXS_GPIO

Travis-CI: https://travis-ci.org/lmajewski/u-boot-dfu/builds/571260789

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2019-08-23 13:59:06 -04:00
Heiko Schocher
49b10cb492 gpio: fixes for gpio-hog support
recently added gpio hog patch was "in discussion"
state with Simon Glass. This patch now adds most
of comments from Simon Glass.

Signed-off-by: Heiko Schocher <hs@denx.de>
2019-07-29 09:32:10 -04:00
Tom Rini
0e80dda32c Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-sunxi
- Beelink-x2 STB support (Marcus)
- H6 DDR3, LPDDR3 changes (Andre, Jernej)
- H6 pin controller, USB PHY (Andre)
2019-07-16 11:19:31 -04:00
Andre Przywara
10cfbaabc1 sunxi: move SUNXI_GPIO to Kconfig
Probably for no particular reason SUNXI_GPIO was still defined the "old
way", in header files only.

Introduce SUNXI_GPIO to the Kconfig file in drivers/gpio to remove
another line from our dreadful config_whitelist.txt.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-16 17:13:15 +05:30
Tom Rini
a9a3a37f92 - syscon: add support for power off
- stm32mp1: add op-tee config
 - stm32mp1: add specific commands: stboard and stm32key
 - add stm32 mailbox driver
 - solve many stm32 warnings when building with W=1
 - update stm32 gpio driver
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJdKK2iAAoJEOKyvdngqpN1TvcH/jj1ujNdRKn994R3DqULzFtc
 Y0WGjAciTUuV0d9gZLxPZJwlWfqxLgbmUEBlPJQJe79gaM7kNN0PgAe6GNedFhGk
 UhRR7GgbA7wogorpRo8aLe3XYEqHtgPFkf1nSiNz/AHLBg8SB20VhWcY90Kha9lh
 IJ0GK+lSdCxiyaLBC2nswnI2PS/fl4NfC7KWvujtKZduIDIOHqh5q+39llpejyuw
 WOzL/bEa4ald6JKpxOii2KXNwD1gUDQGmPzADYcIdwzJtx9hft7DBSLC5Nr+ndBz
 72TjpbtfJ/qIurv8HeXYs9mtwnCO3WP+015fog0T0zjZ48BrT1A8C96ezwLOfz0=
 =W3ny
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20190712' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm

- syscon: add support for power off
- stm32mp1: add op-tee config
- stm32mp1: add specific commands: stboard and stm32key
- add stm32 mailbox driver
- solve many stm32 warnings when building with W=1
- update stm32 gpio driver
2019-07-14 09:09:49 -04:00
Heiko Schocher
5fc7cf8c8e gpio: add gpio-hog support
add gpio-hog support. GPIO hogging is a mechanism
providing automatic GPIO request and configuration
as part of the gpio-controller's driver probe function.

for more infos see:
doc/device-tree-bindings/gpio/gpio.txt

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Michal Simek <michal.simek@xilinx.com> (zcu102)
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-13 11:11:30 -04:00
Patrice Chotard
95fbdd1ad8 gpio: stm32: Rename stm32f7_gpio to stm32_gpio
As this driver is used on stm32f4/f7/h7 and stm32mp1
SoCs, rename it with a more generic name.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:50:58 +02:00
Marek Vasut
86b8e7d61a gpio: renesas: Add RZ/A1 R7S72100 GPIO driver
Add GPIO driver for RZ/A1 SoC. The IP is very different from the
R-Car Gen2/Gen3 one already present in the tree, hence a custom
driver.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-05-07 05:41:32 +02:00
Weijie Gao
16b94903e2 mips: rename mach-mt7620 to mach-mtmips
Currently mach-mt7620 contains only support for mt7628. To avoid confusion,
rename mach-mt7620 to mach-mtmips, which means MediaTek MIPS platforms.
MT7620 and MT7628 should be distinguished by SOC_MT7620 and SOC_MT7628
because they do not share the same lowlevel codes.

Dependencies of four drivers are changed to SOC_MT7628 as these drivers
are only used by MT7628.

Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-05-03 16:43:11 +02:00
Philippe Reynes
353496b756 gpio: bcm6345: allow this driver on ARCH_BCM63158
This IP is also used on some arm SoC, so we allow
to use this driver on arch bcm63158.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12 17:32:51 +02:00
Philippe Reynes
14c9bd46e5 gpio: bcm6345: allow this driver on ARCH_BCM6858
This IP is also used on some arm SoC, so we allow
to use this driver on arch bcm6858.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12 17:32:51 +02:00
Peng Fan
1610368234 gpio: introduce CONFIG_SPL_DM_PCA953X
Introduce CONFIG_SPL_DM_PCA953X for SPL usage.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28 20:35:47 +01:00
Lars Povlsen
ace9c103df mips: gpio: mscc: Obsoleted gpio-mscc-bitbang-spi.c
With the new mscc_bb_spi.c driver, there is no longer use for the
gpio-mscc-bitbang-spi.c driver.

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-01-16 13:56:43 +01:00
Lars Povlsen
be8313feee mips: mscc_sgpio: Add the MSCC serial GPIO device (SIO)
This add support for the the MSCC serial GPIO driver in MSCC
VCoreIII-based SOCs.

By using a serial interface, the SIO controller significantly extends
the number of available GPIOs with a minimum number of additional pins
on the device. The primary purpose of the SIO controller is to connect
control signals from SFP modules and to act as an LED controller.

This adds the base driver.

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
2019-01-16 13:56:43 +01:00
Gregory CLEMENT
02aea4da1d gpio: mscc-bitbang-spi: Add a simple gpio driver for bitbgang spi
The VCore III SoCs such as the Luton but also the Ocelot can remap an SPI
flash directly in memory. However, for writing in the flash the
communication has to be done by software.

Each of the signal used for the SPI are exposed in a single register. In
order to be able to use the soft-spi driver, the management of this pin
is done through this simple gpio driver.

Even if the main purpose of this driver is to be used by soft-spi, it can
still be used as a normal gpio driver but with limitation: for example
the first pin can't be used as output.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-12-19 15:23:01 +01:00
Stefan Roese
4751e5595e gpio: Add MT7621 GPIO support
This patch adds GPIO support for the Mediatek MT7621 SoC, tested on
MT7688 (Gardena smart-gateway). The driver is loosly based on the
Linux kernel version.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[fixed checkpatch.pl warnings: Prefer 'unsigned int' to bare use of 'unsigned']
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-11-18 16:02:22 +01:00
Adam Ford
5d653afc17 Convert CONFIG_DA8XX_GPIO to Kconfig
This converts the following to Kconfig:
   CONFIG_DA8XX_GPIO

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-23 14:33:21 -04:00
Michal Simek
4a69366967 microblaze: Convert generic platform to DM gpio
Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.

GPIO reset is handled via sysreset with adding this fragment to DT.

gpio-restart {
	compatible = "gpio-restart";
	gpios = <&reset_gpio 0 0 0>;
	/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};

hard-reset-gpio property is not documented and also handled.
Conversion is required.

Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:55 +02:00
Hannes Schmelzer
8fd05fccc8 drivers/gpio/mxc: fix MXC GPIO name in KConfig
The naming with "UART" is obviously wrong, we fix this here.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-06-18 16:50:07 +02:00
Patrick Delaunay
2514c2d0e6 arm: stm32: add new architecture for STM32MP family
- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader
- using driver model for all the drivers, even in SPL
- all security feature are deactivated (ETZC and TZC)
- reused STM32 MCU drivers when it is possible

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-19 16:14:21 -04:00
Vipul Kumar
71d5a14204 microblaze: Added Kconfig support for CONFIG_XILINX_GPIO
This patch added Kconfig support for CONFIG_XILINX_GPIO
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01 15:43:45 +01:00