Commit graph

500 commits

Author SHA1 Message Date
Samuel Holland
e008e5132f sunxi: fix initial environment loading without MMC
Commit e42dad4168 ("sunxi: use boot source for determining environment
location") changed our implementation of env_get_location() and enabled
it for every board, even those without MMC support (like the C.H.I.P.
boards). However the default fallback location of ENVL_FAT requires MMC
support compiled in, so the board hangs when trying to initially load
the environment.

Change the algorithm to only return configured environment locations,
and improve the fallback algorithm on the way.

The env_init() routine calling this function here does not behave well
if the return value is ENVL_UNKNOWN on the very first call: it will make
U-Boot proper silently hang very early.
Work around this issue by making sure we return some configured (dummy)
environment location when prio is 0. This for instance happens when
booting via FEL.

This fixes U-Boot loading on the C.H.I.P. boards.

Fixes: e42dad4168 ("sunxi: use boot source for determining environment location")
Reported-by: Chris Morgan <macroalpha82@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fix FEL boot case by not returning ENVL_UNKNOWN when prio==0]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-06-26 11:22:54 +01:00
Samuel Holland
3ba0a25c44 sunxi: Skip MMC0 init when its pinmux conflicts with UART0
Currently, selecting UART0_PORT_F entirely disables MMC support on sunxi
platforms. But this is a bigger hammer then needed. Muxing UART0 to the
pins on port F only causes a conflict with MMC0, so minimize the impact
by specifically skipping MMC0 init. We can continue to use MMC1/2 if
those are enabled.

Let's also remove the preprocessor check while refacting this function.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-05-24 01:14:35 +01:00
Peng Fan
151a030063 arm: set cntfrq_el0 if CONFIG_COUNTER_FREQUENCY is valid
Since COUNTER_FREQUENCY is obselete, so set cntfrq_el0 if
CONFIG_COUNTER_FREQUENCY is valid

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
2022-04-21 15:27:18 -04:00
Samuel Holland
a0ca51f70b sunxi: Support building a SPL as a TOC0 image
Now that mkimage can generate TOC0 images, and the SPL can interpret
them, hook up the build infrastructure so the user can choose which
image type to build. Since the absolute load address is stored in the
TOC0 header, that information must be passed to mkimage.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
8c2bdff483 sunxi: Remove non-DM MMC pin setup
This is now handled automatically by the pinctrl driver.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
aadf3d5383 sunxi: Remove options and setup code for I2C2-I2C4
These options are not currently enabled anywhere. Any new users should
use DM clocks and pinctrl.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
3e42d919af sunxi: Remove non-DM GMAC pin setup
This is now handled automatically by the pinctrl driver.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Andre Przywara
e943753dc2 sunxi: Fix old GMAC pinmux setup
Commit 5bc4cd05d7 ("sunxi: move non-essential code out of s_init()")
moved the call to eth_init_board() from s_init() into board_init_f().
This means it's now only called from the SPL, which makes sense for
most of the other moved low-level functions. However the GMAC pinmux and
clock setup in eth_init_board() was not happy about that, so it broke
the sun7i GMAC.

Since Ethernet is of no use in the SPL anyway, just move the call into
board_init(), which is only run in U-Boot proper.

This fixes Ethernet operation for the A20 SoCs, which broke in
v2022.04-rc1, with the above mentioned commit.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Petr Štetiar <ynezz@true.cz> [a20-olinuxino-lime2]
2022-03-26 00:16:06 +00:00
Andre Przywara
e42dad4168 sunxi: use boot source for determining environment location
Currently we only support to load the environment from raw MMC or FAT
locations on Allwinner boards. With the advent of SPI flash we probably
also want to support using the environment there, so we need to become
a bit more flexible.

Change the environment priority function to take the boot source into
account. When booted from eMMC or SD card, we use FAT or MMC, if
configured, as before.
If we are booted from SPI flash, we try to use the environment from
there, if possible. The same is true for NAND flash booting, although
this is somewhat theoretical right now (as untested).

This way we can use the same image for SD and SPI flash booting, which
allows us to simply copy a booted image from SD card to the SPI flash,
for instance.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2022-03-10 17:33:50 +05:30
Tom Rini
3aaabfe9ff Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
This is the promised second part of the sunxi PR for 2022.04, albeit
technially outside of the merge window. We were working on this full
steam since the beginning of the year, and it deserves to be merged,
I think.
The main attraction is support for the F1C100s SoC, which sports a
venerable ARM926 core. Support for this SoC and the LicheePi Nano board
has been in Linux for years, and U-Boot patches were posted mid last
year already.
The new SoC using ARMv5 also means that the bulk of the new code should
not touch any existing boards, although we did some refactorings first,
of course, which actually cleans up some existing sunxi code.

Compile tested for all 160 sunxi boards, and briefly tested on BananaPi M1,
OrangePi Zero, Pine64 and Pine-H64. Tested by others on their boards,
including F1C100s and F1C200s devices.
2022-02-03 23:24:31 -05:00
Icenowy Zheng
116e1ed1ab sunxi: board: Add support for SUNIV
Generic Timer Extension is not available on SUNIV.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-02-04 00:09:57 +00:00
Chris Morgan
52bcc4f053 sunxi: Add option to prevent booting on power plug-in
For sunxi boards with the AXP209, AXP221, AXP809, and AXP818 PMICs
(plus possibly others, I only confirmed the datasheets for these),
it is sometimes desirable to not boot whenever the device is
plugged in. An example would be when using the NTC CHIP inside a
PocketCHIP.
This provides a configurable option to check if bit 0 of
register 0 of the PMIC says it was powered because of a power button
press (0) or a plug-in event (1). If the value is 1 and this option
is selected, the device shuts down shortly after printing a message
to console stating the reason why it's shutting down. Powering up the
board with the power button is not affected.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[Andre: reword to speak of boot, remove #ifdefs]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-01-30 01:25:00 +00:00
Giulio Benetti
d0ffd15cff sunxi: dram_sun4i/5i: use DRAM_MEMORY_TYPE_DDR3 instead of magic number 3
Since DRAM_MEMORY_TYPE_DDR3 is defined let's use it instead of magic
number 3.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-01-30 01:03:37 +00:00
Icenowy Zheng
2753b07269 sunxi: call fdt_fixup_ethernet again to set macaddr for more aliases
Sometimes some ethernet aliases do not exist in U-Boot DT but they
exist in the DT used to boot the system (for example, modified via DT
overlays). In this situation setup_environment is called again in
ft_board_setup() to generate macaddr environment variable for them.
However now the call to fdt_fixup_ethernet() is moved before the call
of ft_board_setup().

Call fdt_fixup_ethernet() again to add MAC addresses for the extra
ethernet aliases.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[updated commit message]
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-01-30 01:03:37 +00:00
Tom Rini
2f8a6db5d8 Finish conversion of CONFIG_SYS_CLK_FREQ to Kconfig
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things.  First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h.  This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.

With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available).  Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27 16:20:18 -05:00
Andre Przywara
fbd9207e7f sunxi: Remove misleading USB-OTG charger message
The sunxi MUSB glue driver has some code to check for external VBUS
presence when it's going to use the MUSB host mode, and it warns if
there is VBUS provided through the cable (in sunxi_musb_enable()).

This code was apparently copied to the USB gadget detection code
(g_dnl_board_usb_cable_connected()), but here we actually *expect*
external VBUS power, so a warning is wrong and confusing.
So far this message rarely triggered, but a recent patch (6fa41cdd19)
changed this:
===========================
=> ums 0 mmc 2
UMS: LUN 0, dev mmc 2, hwpart 0, sector 0x0, count 0xe90000
A charger is plugged into the OTG
/A charger is plugged into the OTG
\A charger is plugged into the OTG
|A charger is plugged into the OTG
-A charger is plugged into the OTG
....
===========================

Remove the message for the gadget cable detection call, and just return
the status of the VBUS detection, as this is what the callers are after.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-12-08 23:07:15 +00:00
Samuel Holland
2421497cb7 sunxi: video: Convert panel I2C to use DM_I2C
Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).

Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.

This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.

Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12 11:01:17 +01:00
Chukun Pan
e7510d24ca sunxi: Add support for FriendlyARM NanoPi R1S H5
This adds support for the NanoPi R1S H5 board.

Allwinner H5 SoC
512MB DDR3 RAM
10/100/1000M Ethernet x 2
RTL8189ETV WiFi 802.11b/g/n
USB 2.0 host port (A)
MicroSD Slot
Reset button
Serial Debug Port
WAN - LAN - SYS LED

The dts file is taken from Linux 5.14 tag.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
425084610e sunxi: Clean up inclusions of asm/arch/gpio.h
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.

Some files did not contain any GPIO code at all, so this header was
completely unused.

A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.

The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Arnaud Ferraris
8f872bb37d board: sunxi: enable status LED early
For some systems, such as the PinePhone, there is no way for the end
user to make sure the system is indeed booting before the boot script is
executed, which takes several seconds. Therefore, it can be useful to
provide early visual feedback as soon as possible.

In order achieve this goal, this patch initializes the status LED (if
configured) in the SPL.

Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
dda9fa734f sunxi: Simplify MMC pinmux selection
Only one board, Yones Toptech BD1078, actually uses a non-default MMC
pinmux. All other uses of these symbols select the default value or an
invalid value. To simplify things, remove support for the unused pinmux
options, and convert the remaining option to a Boolean.

This allows the pinmux to be chosen by the preprocessor, instead of
having the code parse a string at runtime (for a build-time option!).
Not only does this reduce code size, but it also allows this Kconfig
option to be used in a table-driven DM pinctrl driver.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Arnaud Ferraris
5427da02be configs: add PineTab defconfig
The PineTab device-tree is already in u-boot, this commit adds the
corresponding defconfig, based on pinephone_defconfig.

Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:43 +01:00
Tom Rini
de69572569 Convert CONFIG_SYS_I2C_SOFT et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_SOFT
   CONFIG_SYS_I2C_SOFT_SPEED
   CONFIG_SYS_I2C_SOFT_SLAVE

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30 14:10:06 -04:00
Samuel Holland
1011ebc72b sunxi: Select environment MMC based on boot device
Currently, the environment is always stored in eMMC if eMMC is enabled
in the config. This means images written to SD and eMMC will cross-
contaminate their environments unless the configuration is changed.

By dropping the device number from the environment location string and
implementing mmc_get_env_dev, we will always use the environment from
the boot device when booting from SD/eMMC.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-08-01 00:11:34 +01:00
Andre Przywara
212224ed68 sunxi: board: Add H616 MMC2 pins
We hardcode the pinctrl setting for the MMC controllers in boards.c,
since we need them also in the SPL, where there is no DT yet.

Add the respective setting for the H616 SoC, to enable eMMC on boards
with this SoC as well.
Also to make diagnosing this problem easier, print a warning if a board
tries to setup MMC2 pins without a respective SoC setting being defined.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan at amarulasolutions.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec at siol.net>
2021-07-10 01:22:09 +01:00
Yu-Tung Chang
2527b24f39 sunxi: h3: Add initial ZeroPi support
ZeroPi is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner H3 SOC.

ZeroPi features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 256MB/512MB DDR3 RAM
- microsd slot
- 10/100/1000Mbps Ethernet
- Debug Serial Port
- DC 5V/2A power-supply

Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-07-10 01:22:09 +01:00
Kory Maincent
6c2c7e9cb9 arm: sunxi: add support for DIP detection to CHIP board
Add the extension_board_scan specific function to scan the information
of the EEPROM on one-wire and fill the extension struct.
Add the Kconfig symbol to enable the needs to detect DIPs.

Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Andre Przywara <andre.przywara@arm.com>
2021-05-13 13:09:09 -04:00
Igor Opaniuk
2147a16983 dm: i2c: use CONFIG_IS_ENABLED macro for DM_I2C/DM_I2C_GPIO
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.

CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.

All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
     's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
    's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
    's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
    's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
    's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
    's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +

Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-21 06:08:00 +01:00
Simon Glass
401d1c4f5d common: Drop asm/global_data.h from common header
Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-02 15:33:42 -05:00
Jernej Skrabec
38be6b8387 sunxi: Add support for OrangePi Zero2
OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card
support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0
port. It also has two GPIO headers which allows further peripherals to
be used.

The devicetree file is taken from v3 of the OrangePi Zero2 Linux
submission [1], which it's not yet merged.

[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632084.html

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:01 +00:00
Jernej Skrabec
d0b07c15c2 sunxi: add support for R_I2C on H616
This port is needed for communication with PMIC. SPL uses it to set DRAM
voltage on H616 boards.

Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:01 +00:00
Jernej Skrabec
fbd37d8d28 sunxi: Add support for AXP305 PMIC
This PMIC can be found on H616 boards and it's very similar to AXP805
and AXP806.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:00 +00:00
Andre Przywara
e9ad1b8dc5 sunxi: Properly check for SATAPWR and MACPWR
The #ifdef CONFIG_xxxPWR conditionals were not working as expected, as
string Kconfig symbols are always "defined" from the preprocessor's
perspective. This lead to unnecessary calls to the GPIO routines, but
also always added a half a second delay to wait for a SATA disk to power
up. Many thanks to Peter for pointing this out!

Fix this by properly comparing the Kconfig symbols against the empty
string. strcmp() would be nicer for this, but GCC does not optimise this
away, probably due to our standalone compiler switches.

Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi WinPlus
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
2021-01-25 21:52:00 +00:00
Andre Heider
c81877a919 sunxi: Add support for Orange Pi 3
dts file is taken from Linux 5.11-rc1 tag.

The Bluetooth controller of this device ships with a default address,
use the new CONFIG_FIXUP_BDADDR option to fix it up.

Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[Updated OrangePi 3 DT, rebase and config update]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:00 +00:00
Jernej Skrabec
a54b2925a6 sunxi: Add support for Tanix TX6
This commit adds support for Tanix TX6 TV box, based on H6. It's low end
H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other
peripherals.

DT file is taken from Linux 5.11-rc1 release.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:00 +00:00
Andre Heider
9267ff89ee sunxi: board: add a config option to fixup a Bluetooth address
Some Bluetooth controllers, like the BCM4345C5 of the Orange Pi 3,
ship with the controller default address.

Add a config option to fix it up so it can function properly.

Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-11 23:19:34 +00:00
Andre Heider
928f4f4868 sunxi: board: extract creating a unique sid into a helper function
Refactor setup_environment() so we can use the created sid for a
Bluetooth address too.

Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-11 23:19:34 +00:00
Andy Shevchenko
92600edb43 sunxi: board: Move USB ethernet initialization to board_late_init()
For the sake of consistency (*) and order of initialization, i.e.
after we have got the ethernet address, interrupt and timer initialized,
try to initialize USB ethernet gadget.

*) for example, zynqmp uses same order.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-11 23:19:34 +00:00
Icenowy Zheng
ab3b53f30f sunxi: add PineCube board
PineCube is an IP camera development kit released by Pine64.

It comes with the following compoents:

- A mainboard with Sochip S3 SoC, a 16MByte SPI Flash, AXP209 PMIC,
a power-only microUSB connector, a USB Type-A connector, a 10/100Mbps
Ethernet port and FPC connectors for camera and daughter board.
- An OV5640-based camera module which is connected to the parallel CSI
bus of the mainboard.
- A daughterboard with several buttons, a SD slot, some IR LEDs, a
microphone and a speaker connector.

As the device tree is synchronized in a previous commit, just add it to
Makefile, create a new MAINTAINER item and provide a defconfig.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-11 23:19:33 +00:00
Icenowy Zheng
8c51c65273 sunxi: allow to use AXP20[39] attached to I2C0 on V3 series
The reference design of Allwinner V3 series uses an
AXP203 or AXP209 PMIC attached to the I2C0 bus of the SoC, although the
first community-available V3s board, Lichee Pi Zero, omitted it.

Allow to introduce support for the PMIC on boards with it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-11-17 00:42:21 +00:00
Samuel Holland
882fb905e0 sunxi: a64: Add a defconfig for the PinePhone
The PinePhone is a smartphone produced by Pine64, with an A64 SoC,
2 or 3 GiB LPDDR3 RAM, 16 or 32 GiB eMMC, 720x1440 MIPI-DSI panel,
and Quectel EG25-G modem.

There are two main board revisions: 1.1 for early adopters, and 1.2
for mass production. Since there is code to detect the board revision
at boot, one config/image can support both boards.

Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2020-11-17 00:42:21 +00:00
Samuel Holland
20f3ee31c3 sunxi: board: Set fdtfile to match the DT chosen by SPL
Previously, fdtfile was always the value in CONFIG_DEFAULT_DEVICE_TREE.
This meant that, regardless of the DT chosen by SPL (either by changing
the header in the image or by the selection code at runtime), Linux
always used the default DT.

By using the name from the SPL header (which, because of the previous
commit, always matches the DT used by U-Boot proper), Linux also sees
the same board as U-Boot/SPL, even if the boot script later loads a DT
from disk.

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: remove no longer needed CONFIG_SPL_LOAD_FIT guards]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2020-11-17 00:42:20 +00:00
Samuel Holland
41530cf681 sunxi: board: Save the chosen DT name in the SPL header
This overwrites the name loaded from the SPL image. It will be different
if there was previously no name provided, or if a more accurate name was
determined by the board variant selection logic. This means that the DT
name in the SPL header now always matches the DT appended to U-Boot.

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: move function under CONFIG_SPL_LOAD_FIT guard]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2020-11-17 00:42:20 +00:00
Samuel Holland
8a8b73b6d7 sunxi: board: Add PinePhone DT selection logic
There are two different publicly-released revisions of the PinePhone
hardware, versions 1.1 and 1.2; and they need different device trees.
Since some GPIO pins were rerouted, we can use that to distinguish
between them.

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-11-17 00:42:20 +00:00
Samuel Holland
54ac5aa174 sunxi: board: Simplify Pine A64 DT selection logic
Instead of using an entirely separate matching algorithm, simply update
the name of the DT we want to match. Enabling this logic does not depend
on the FIT config name, only on the initial guess of the board name.

Importantly, the initial guess must be "sun50i-a64-pine64-plus", because
otherwise the logic would trigger when "sun50i-a64-pine64-lts" was
written to the SPL header.

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-11-17 00:42:20 +00:00
Samuel Holland
467b7e52ec sunxi: board: Add a helper to get the SPL DT name
This moves the validity checking and typecasts all to one place away
from the string comparison logic, and it detangles the compile-time
and runtime control flow.

The new helper will also be used by U-Boot proper in a future commit.

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: protect new function with CONFIG_SPL_LOAD_FIT]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2020-11-17 00:42:20 +00:00
Samuel Holland
2fcd74899c sunxi: board: Use a more descriptive variable name
The variable "cmp_str" always leaves me wondering if it is the DT name
of the current board (yes) or DT name in the FIT config entry (no).

In preparation for expanding the functionality here, rename it to
something that obviously means "this is the DT name we are looking for".

Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-11-17 00:42:20 +00:00
Samuel Holland
e72a6be4fc sunxi: binman: Add support for including SCP firmware
Allwinner sun50i SoCs contain an OpenRISC 1000 CPU that functions as a
System Control Processor, or SCP. ARM Trusted Firmware (ATF)
communicates with the SCP over SCPI to implement the PSCI system
suspend, shutdown and reset functionality. Currently, SCP firmware is
optional; the system will boot and run without it, but system suspend
will be unavailable.

Since all communication with the SCP is mediated by ATF, the only thing
U-Boot needs to do is load the firmware into SRAM. The SCP firmware
occupies the last 16KiB of SRAM A2, immediately following ATF.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-10-22 11:43:43 +05:30
Simon Glass
f5bbd9a3a6 sunxi: Drop the FIT-generator script
This file is no-longer used. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-09-22 12:50:43 -06:00
Patrick Delaunay
f286e37c14 board: sunxi: change trace level for phy errors managed by uclass
As the error message is now displayed by generic phy functions,
the pr_err can be change to pr_idebug.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-09-08 08:46:32 -04:00