This patch adds support for the common AHCI controller on the Marvell
Armada 38x.
Tested on the Marvell DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch changes the initialization of the AHCI controller to not
enable the default interrupts (DEF_PORT_IRQ). As interrupts are
not used in U-Boot in general, this should not break the common AHCI
driver operation.
This change is needed to support the Marvell Armada 38x AHCI
controller. With interrupts enabled, this results in timeouts in
ahci_device_data_io(). Not enabling these interrupts fixes this
problem and the common AHCI driver works fine.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds MMC/SDIO support to the Marvell DB-88F6820-GP board
configuration. Including support for the common partitions and
filesystems.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Armada A38x implements an SDHCI compatible SDIO controller. This patch
enables the Marvell driver to support this SoC. And enables the
SDIO controller if selected by the board configuration.
Tested on Marvell DB-88F6820-GP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
While implementing SDIO/MMC SPL booting for the Marvell Armada 38x, the
following problem occured. The SPL runs in internal SRAM which is
the L2 cache locked to memory. When the MMC buffers now are located
on the stack (or bss), the SDIO controller (SDHCI) can't write into
this L2 cache memory.
This patch introduces a method to use a fixed buffer that will be
used for all transfers by defining CONFIG_FIXED_SDHCI_ALIGNED_BUFFER.
This way, the board can use this buffer address located in SDRAM
for all transfers. This solves this SPL problem on the A38x and
should only be used in the SPL U-Boot version.
Tested for SPL booting on Marvell Armada 38x DB-88F6820-GP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The loop counter based timeout detection does not work on the Armada
38x based board (DB-88F6820-GP). At least with dcache enabled a
timeout is detected. Without dcache enabled, the timeout does not
occur. Increasing the loop counter solves this issue. But a better
solution is to use a timer based timeout detection instead. This
patch now implements this timer based detection.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
commit f566c99 "net: Update hardware MAC address if it changes in env"
removes writing MAC address to designware controller after soft reset.
This makes designware ethernet port fail to work. Actually the MAC
address should always be programmed after soft reset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
sun8i-a33-ippo-q8h-v1.2-lcd1024x600.dts has been merged into the upstream
Linux kernel as sun8i-a33-ippo-q8h-v1.2.dts, adjust u-boot to follow.
Note we've never shipped a final u-boot version with the old name, so this
is safe todo.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
we currently use in-development IODelay values for DRA72x which are
proposed in the data sheet, however, DRA72x EVM uses DP83865 ethernet
Phy over RGMII. The PHY characteristics and routing choices made on
the EVM, make the current iodelay values fail ethernet communication.
Instead, we need to choose custom values for DRA72x-evm specifically
designed for the PHY and routing on the platform for ethernet to
function.
Cc: Nishanth Menon <nm@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
We have not supported the private library for ARM 64bit.
Prohibit ARM64 boards from enabling it until we make things ready.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
am43xx_evm_ethboot/usbhost_boot_defconfig entries are
missing in MAINTAINER file. Adding entries for them.
Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This removes the following two warnings from buildman:
WARNING: no status info for 'cairo'
WARNING: no maintainers for 'cairo'
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Added UART DCC support for armv8
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The root cause of this problem should now be fixed.
This reverts commit a6a4c542d3.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>
When CONFIG_SYS_THUMB_BUILD is defined these functions may be called from
Thumb code. Add the required ENTRY and ENDPROC bracketing so that BLX is
used to call these ARM functions, instead of plain BL, which will fail.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Pavel Machek <pavel@denx.de>
The LPC32XX GPIO driver platdata currently contains GPIO state information,
which should go into priv_data. Thus rename lpc32xx_gpio_platdata to
lpc32xx_gpio_priv and convert to use dev_get_priv() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
Sinlinx SinA33 is a core/daughter board SDK kit from Sinlinx. It has
the A33 SoC, USB host, USB OTG, audio input/output, LCD, camera, SDIO
and GPIO headers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Copy over all the latest dts changes from mripard/sunxi/dt-for-4.2.
This adds a dts file for Sinlinx SinA33 dev board, and the required
changes in the .dtsi files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A33 adds a pinmux function for UART0 in the PB pin group.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The original code was configuring the external pins after enabling
the R_PIO clock, which meant the configuration never made it to
the pin controller the first time in SPL.
Why this was working before is uncertain. Maybe the state was left
from a previous boot sequence, or RSB just happened to be the default
configuration. However with some A33 chips, SPL failed to configure
the PMIC. This was seen by me and Maxime on the Sinlinx SinA33 dev
board.
Reordering the calls fixed this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit 487b327 ("sunxi: GPIO pin mux hardware-feature-specific function
index defines") renamed all GPIO index defines, but missed the PORT F
UART0 setup functions.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Increase console IO buffer size to 1024 from the previous value of 256.
The previous value was too short for editing environment variables like
ubiboot from the console.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Added TEGRA20_SLINK entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Added TEGRA20_SFLASH entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Added TEGRA114_SPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Added ICH_SPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Added FSL_QSPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Haikun Wang <haikun.wang@freescale.com>
DM supported spi drivers are enbled only when DM_SPI enabled,
so added DM_SPI if condition in Kconfig to show thoese only
when it enabled.
Also re-order the config items as incresing alphabetic order.
Signed-off-by: Jagan Teki <jteki@openedev.com>
