Vanessa's NXP e-mail is no longer active.
Contacted her offline and she told me that she does not have
access to the board anymore and it is OK to remove her
from MAINTAINERS.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Errors were handled only if an I2C transfer timed out
and received a NACK which is very unlikely. This commit
changes the condition such that errors are handled if
an I2C transfer times out or received a NACK.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Reviewed-by: Heiko Schocher <hs@denx.de>
The NETSEC GMAC occasionally falls into a weird state where
MAC_REG_DESC_SOFT_RST has never been cleared and shows errors like the
below when networking commands are issued:
=> ping 192.168.1.1
ethernet@522d0000 Waiting for PHY auto negotiation to complete... done
netsec_wait_while_busy: timeout
Using ethernet@522d0000 device
ARP Retry count exceeded; starting again
ping failed; host 192.168.1.1 is not alive
It happens on not only 'ping' but also 'dhcp', 'tftp' and so on.
Luckily, restarting the NETSEC GMAC and trying again seems to fix the
problematic state. So first ensure that we haven't entered the state by
checking MAC_REG_DESC_SOFT_RST to be cleared; otherwise, restarting
NETSEC/PHY and trying again would work as a workaround.
Signed-off-by: Ryosuke Saito <ryosuke.saito@linaro.org>
Tested-by: Masahisa Kojima <masahisa.kojima@linaro.org>
commit 280f45d239 ("configs: get rid of build warnings due to
SPL_USB_DWC3_GENERIC") missed enabling DWC3 glue layer for
usbmsc_defconfig and this broke boot from USB mass storage.
Fix this by enabling DWC3 glue layer.
Fixes: 280f45d239 ("configs: get rid of build warnings due to SPL_USB_DWC3_GENERIC")
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Make sure to stay within bounds, as a misbehaving HTTP server
can trigger a buffer overflow if not properly handled.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Use fdt_fixup_memory to make the memory size data from dtb match
the actual size.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
Enable CONFIG_OF_BOARD_SETUP, so we could use ft_board_setup() to fixup
memory size passed to kernel.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on R-Car Gen3 Salvator-X boards. This allows software
to identify the PHY model at any time, regardless of the state of
the PHY reset line.
This is a fix for missed addition of these properties on Salvator-X
boards.
Ported from Linux kernel commit 722d55f3a9bd810f3a1a31916cc74e2915a994ce .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Move BinmanLogging reference tag after section "Signing FIT container
with private key in an image" and just before section "Logging".
Fixes: 0f40e23fd2 ("binman: add documentation for binman sign option")
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The test_event_base and test_event_probe unit tests use function
event_register() which depends on CONFIG_EVENT_DYNAMIC=y.
Fixes: 7d02645fe4 ("event: Add a simple test")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Previously, the file extension was .txt, and it referenced the uImage.FIT
directory, which no longer exists. This commit updates the path accordingly.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
To avoid confusion document that timer_dev_priv.clock_rate and
timer_get_rate() yield the timer rate in hertz.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 64-bit app is supported now, so update the documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We don't have a documentation page for our TPM subsystem. I plan
on sending one in the future, but in the meantime document the
new 'tpm autostart' command in the QEMU instructions while using
a SWTPM
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
On commit e663b2ff4ba2("tpm: Add 'tpm autostart' shell command") an
autostart function was added for both TPM1.2 and 2.0 devices. Instead
of correctly wiring the autostart command for TPM1.2 devices that patch
mistakenly added it on 'tpm init'
Fixes: commit e663b2ff4ba2("tpm: Add 'tpm autostart' shell command")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
spl_blk_load_image() should not return an uninitialized value if
blk_get_devnum_by_uclass_id() fails.
Fixes: 8ce6a2e175 ("spl: blk: Support loading images from fs")
Reported-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
+ Implement OpenSBI DBCN extension for early debug console
+ Fixes for VisionFive2 board
+ Fix timer missing
+ Fix L2 LIM issue
+ Enable PCIE auto enumeration to support USB and NVMe by default
+ Set eth0 mac address properly
+ Add __noreturn attribute to spl_invoke_opensbi
Use the DBCN SBI extension to implement a debug console.
Make it the default for S-mode RISC-V.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The DBCN extension provides a Console Write Byte call.
Implement function sbi_dbcn_write_byte to invoke it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
spl_invoke_opensbi function is not returned to SPL. Thus, we need to
set __noreturn function attribute.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
SPL_SYS_MALLOC_CLEAR_ON_INIT would enable SYS_MALLOC_CLEAR_ON_INIT by
default, but that's not need on JH7110, so disable that.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Starfive JH7110 needs to clear L2 LIM to zero before use or ECC error
would be triggered. Currently, we use DDR ram for SPL malloc arena on
Visionfive 2 board in defconfig, but it's also possible to use L2 LIM as
SPL malloc arena. To avoid triggering ECC error in this scenario, we
imply SPL_SYS_MALLOC_CLEAR_ON_INIT as default.
Signed-off-by: Bo Gan <ganboing@gmail.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
To support SPL_SYS_MALLOC_CLEAR_ON_INIT, we have to modify
#ifdef CONFIG_SYS_MALLOC_CLEAR_ON_INIT
to #if CONFIG_IS_ENABLED(SYS_MALLOC_CLEAR_ON_INIT)
Signed-off-by: Bo Gan <ganboing@gmail.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add SPL version of SYS_MALLOC_CLEAR_ON_INIT, this would help devices
that need to clear ram before use to work correctly.
Signed-off-by: Bo Gan <ganboing@gmail.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since PLDA PCIE driver is added and VL805 support is enabled in
defconfig for Starfive Visionfive 2, modify the document to keep
consistent.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
Although PCIE driver already exists, board defconfig isn't configured to
enable PCIE enum on boot, thus USB storage device and NVME drive are not
supported by default. So modify defconfig to enable PCIE auto enum, then
start USB subsystem and scan nvme drive on boot.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
The JH7110 has the arhitectural CPU timer on all 5 rv64 cores.
Note that in the device tree.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
For the architectural timer on riscv, there already is a defined
device tree binding[1]. Allow timer instances to be created from
device tree matches, but for now retain the old mechanism, which
registers the timer biggy-back with the CPU.
[1] linux/Documentation/devicetree/bindings/timer/riscv,timer.yaml
Signed-off-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
fdt_fixup_ethernet() sets eth0 mac address from ethaddr. Set
ethaddr to environment instead of eth0addr.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This platform is behind on migrations (it is the sole user of the oldest
legacy version of the USB gadget stack and is long overdue for
migration) and with Pali no longer being a maintainer, we remove this
platform.
Signed-off-by: Tom Rini <trini@konsulko.com>
Polling every second to check whether the CPU has cooled down is
too frequent.
Allow more time for the CPU to cool down by increasing the polling
interval to 5 seconds by defaut.
This value is used in the absence of the 'polling-delay' devicetree
property.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The temperature unit is millidegree Celsius, so divide by 1000 to correctly
print the temperature values in Celsius.
While at it, also change a typo: "has beyond" to "is beyond".
Signed-off-by: Fabio Estevam <festevam@denx.de>
dev_info() message is not printed by default. Increase the log level
to dev_crit(). This allows the critical messages related to the temperature
getting beyong the alert threshold to be displayed.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
When the 'polling-delay' property is not passed via devicetree,
pdata->polling_delay keeps at 0. This causes the imx_tmu driver to get
stuck inside the busy while() loop when the CPU temperature is above
the alert point.
Fix this problem by passing a one second polling interval, which provides
a proper delay to let the system to cool down and exit the while() loop
when the temperature is below the alert point.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Select the i.MX8MM thermal driver as it is useful for displaying
the CPU temperature and its grading:
CPU: Commercial temperature grade (0C to 95C) at 38C
It also prevents booting when the temperature is above the alert
point.
Signed-off-by: Fabio Estevam <festevam@denx.de>
