In commit 6f46c7441a ("phy: cadence: Sierra: Add a UCLASS_PHY device for
links"), a separate udevice of type UCLASS_PHY was created for each link.
Therefore, move the corresponding link operations under the link device.
Also, change the uclass of sierra phy to UCLASS_MISC as it is no longer the
phy device.
Fixes: 6f46c7441a ("phy: cadence: Sierra: Add a UCLASS_PHY device for links")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Georgi Vlaev <g-vlaev@ti.com>
Ensure there is a valid reset-gpio defined before using it.
Fixes: f9852acdce ("phy: nop-phy: Fix enabling reset")
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The reset function should place the phy into reset, while the
init function should take the phy out of reset. Currently the
reset function takes it out of reset, and the init calls the
reset.
Signed-off-by: Adam Ford <aford173@gmail.com>
The port/hub leaf nodes don't contain the phy definitions in some dts
files so check the parents.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Simon Glass <sjg@chromium.org>
Official DT bindings use compatible string marvell,armada-3700-ehci.
Update drivers and DTS files.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
In commit d368e10705 ("phy: marvell: a3700: Convert to official DT
bindings in COMPHY driver") was done update to official DT bindings but
compatible string of official DT bindings was not updated.
Fix it now.
Fixes: d368e10705 ("phy: marvell: a3700: Convert to official DT bindings in COMPHY driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Some usb-nop-xceiv devices use a gpio take them out
of reset. Add a reset function to put them into that
state. This is similar to how Linux handles the
usb-nop-xceiv driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
In some cases, a single SerDes instance can be shared between two different
processors, each using a separate link. In these cases, the SerDes
configuration is done in an earlier boot stage. Therefore, add support to
skip reconfiguring, if it is was already configured beforehand.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add support for multilink configuration of Sierra PHY. Currently,
maximum two links are supported.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add single link PCIe register configurations for no SSC and internal
SSC. Also, add missing PMA lane registers for external SSC.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
PIPE phy status is used to communicate the completion of several PHY
functions. Check if PHY is ready for operation while configured for
PIPE mode during startup.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Check if PMA cmn_ready is set indicating the startup process is complete.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add PHY PCS common register configuration sequences for single link.
Update single link PCIe register sequence accordingly.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
No functional change. Rename some regmap variables as mentioned in Sierra
register description documentation.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Sierra driver currently supports single link configurations only. Prepare
driver to support multilink multiprotocol configurations along with
different SSC modes.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Sierra has two PLLs, PLL_CMNLC and PLL_CMNLC1 and each of these PLLs has
two inputs, plllc_refclk (input from pll0_refclk) and refrcv (input from
pll1_refclk). Model PLL_CMNLC and PLL_CMNLC1 as a clock so that it's
possible to select one of these two inputs from device tree.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add missing clk_disable_unprepare() in cdns_sierra_phy_remove().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Instead of having separate structure members for each input clock, add
an array for the input clocks within "struct cdns_sierra_phy". This is
in preparation for adding more input clocks required for supporting
additional clock combination.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
No functional change. Group devm_reset_control_get() and
devm_reset_control_get_optional() to a separate function.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
No functional change. Group all devm_clk_get_optional() to a
separate function.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Cadence Sierra PHY driver registers PHY using devm_phy_create()
for all sub-nodes of Sierra device tree node. However Sierra device
tree node can have sub-nodes for the various clocks in addtion to the
PHY. Use devm_phy_create() only for nodes with name "phy" (or "link"
for old device tree) which represent the actual PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Commit 39b823381d ("phy: cadence: Add driver for Sierra PHY")
de-asserts PHY_RESET even before the configurations are loaded in
phy_init(). However PHY_RESET should be de-asserted only after
all the configurations has been initialized, instead of de-asserting
in probe. Fix it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This weak function is not used anymore, so completely remove it.
Private struct comphy_map is not used by any board code anymore, so move it
into private driver header file comphy_core.h.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
On boards using the RK3399 SoC, the USB OHCI and EHCI controllers share
the same PHY device instance. While these controllers are being stopped
they both attempt to power-off and deinitialize it, but trying to
power-off the deinitialized PHY device results in a hang. This usually
happens just before booting an OS, and can be explicitly triggered by
running "usb start; usb stop" in the U-Boot shell.
Implement a uclass-wide counting mechanism for PHY initialization and
power state change requests, so that we don't power-off/deinitialize a
PHY instance until all of its users want it done. The Allwinner A10 USB
PHY driver does this counting in-driver, remove those parts in favour of
this in-uclass implementation.
The sandbox PHY operations test needs some changes since the uclass will
no longer call into the drivers for actions matching its tracked state
(e.g. powering-off a powered-off PHY). Update that test, and add a new
one which simulates multiple users of a single PHY.
The major complication here is that PHY handles aren't deduplicated per
instance, so the obvious idea of putting the counts in the PHY handles
don't immediately work. It seems possible to bind a child udevice per
PHY instance to the PHY provider and deduplicate the handles in each
child's uclass-private areas, like in the CLK framework. An alternative
approach could be to use those bound child udevices themselves as the
PHY handles. Instead, to avoid the architectural changes those would
require, this patch solves things by dynamically allocating a list of
structs (one per instance) in the provider's uclass-private area.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com> - Rock960
Somewhere along the way, someone misspelt "invalid" and it got copied
everywhere. Fix it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add PSGTR driver for Xilinx ZynqMP.
The most of configurations are taken from Linux kernel psgtr driver.
USB3.0 and SGMII configurations are tested on SOM. In SGMII case also
IOU_SLCR reg is updated to get proper clock setup and signal detection
configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/36e6e9d3baf8511af1916e91e4887032ca2b6c20.1641458978.git.michal.simek@xilinx.com
Convert A3720 common PHY driver to official DT bindings.
This puts us closer to be able to synchronize A3720 device-trees with
those from Linux.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The device tree binding provides for getting VBUS state from a device
referenced by phandle, as an optional alternative to using a GPIO. In
U-Boot, where there is no power supply class, this VBUS detection will
be implemented using a regulator device and its get_enable method.
Let's hook this up to the PHY driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Linux driver checks the VBUS detection GPIO first; then VBUS power
supply; then finally assumes VBUS is present. When adding VBUS power
supply support, we want to match that order, so we get the same behavior
in case both a GPIO and a power supply are provided in the device tree.
So refactor the function a bit to remove the early return, and use the
same "assume VBUS is present" final fallback.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Both of these messages log the GPIO number of the ID detection GPIO,
which is not terribly useful, especially in the VBUS detection function.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
Subroutines in comphy_usb2_power_up() and comphy_sgmii_power_up() functions
may fail. In this case, do not continue execution of current function and
instead jump to the end. Return value in 'ret' variable is already set.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
phy_txd_inv or phy_rxd_inv needs to be set only in case when
appropriate polarity is inverted. Otherwise these bits should be
cleared.
Same change was included in TF-A project:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/9406
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marvell Armada 3700 Functional Specifications, section 52.2 PCIe Link
Initialization says that TXDCLK_2X_SEL bit needs to be enabled for PCIe
Root Complex mode.
Same change was included in TF-A project:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/9408
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add protection on presence and order of the phy node sub node
by using the mandatory reg information.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The vbus-supply is an optional property of sub-node connector node.
and no more in the usb phyc node (in first proposed binding).
This regulator for USB VBUS may be needed for host mode.
See the latest kernel binding for details in
Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml.
usbphyc_port0: usb-phy@0 {
reg = <0>;
phy-supply = <&vdd_usb>;
#phy-cells = <0>;
connector {
compatible = "usb-a-connector";
vbus-supply = <&vbus_sw>;
};
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
