According to doc/README.distro fdt_addr must not be set when DTB is not
available from hardware. So remove this entry.
Use address 32MB above the start of DRAM for kernel_addr_r. This way
we likely can avoid the self-relocation of the compressed kernel image
before it decompresses to offset 0x8000 from start of DRAM.
Use address 128MB above the start of DRAM for fdt_addr_r, since this is
the maximum location for the end of the kernel. So we avoid overwriting
the DTB.
Use 512k above that for ramdisk_addr_r. This should be enough for the
DTB, rest of DRAM can be used for initrd.
Place boot script / extlinux.conf at offset 0 / 1MB from start of DRAM.
This space is available for processing in U-Boot.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the RPC Hyperflash driver on R8A7795,R8A7796,R8A77965
Salvator-X,ULCB and R8A77990 Ebisu. Note that to make the HF
accessible, mainline ATF is mandatory and must be built with
RCAR_RPC_HYPERFLASH_LOCKED=0 . Note that this is intended for
development and testing convenience only and must be disabled
in deployment for platform security reasons.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
Increase max gunzip size, required for booting itb recovery images on
uDPU.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
[a.heider: adapt to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
scan_dev_for_efi is supposed to be called from scan_dev_for_boot.
However this call is missing for ls1028ardb and ls1028aqds boards. As
a result EFI boot doesn’t work. Fix this issue by removing custom
definition of scan_dev_for_boot and use the default definition
instead.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: andy.tang@nxp.com
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
PXE and DHCP shouldn't be listed when commands are not enabled that's why
handle it in the same way as is done for Zynq and ZynqMP.
Fixes: ec48b6c991 ("arm64: versal: Add support for new Xilinx Versal ACAPs")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch moves the the config SYS_MALLOC_LEN to Kconfig
as it is already done for zynq arch in commit 01aa5b8f05
("Kconfig: Move config SYS_MALLOC_LEN to Kconfig for zynq").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Provide fdtfile value in default env instead of setting
it dynamically in runtime.
Fixes: 85cb2bc686("apalis/colibri imx6: provide proper fdtfile value")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Provide fdtfile value in default env instead of setting
it dynamically in runtime.
Fixes: 85cb2bc686("apalis/colibri imx6: provide proper fdtfile value")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: a62c60610f("colibri_imx7_emmc: add Colibri iMX7D 1GB (eMMC) module support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: 304042c1f3("colibri_vf: set fdtfile for distroboot")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: board: 31b1e17f44("toradex: add Colibri iMX6ULL support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Set proper splashscreen env value instead of calling legacy function
to show embed boot logo.
Fixes: 195011b24d("colibri-imx7: fix splash logo drawing")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Set proper splashscreen env value instead of calling legacy function
to show embed boot logo.
Fixes: 391c712dde("colibri-imx6ull: show boot logo")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
enable DTS support for keymile mpc83xx based boards.
get rid of compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Therefore done:
- add DTS for all mpc83xx based boards from keymile
mainly they are not mainlined to linux.
- add u-boot specific dtsi
- add stdout-path
- add missing ucc4 par_io definitions, which were
in board code, but not in linux DTS
- remove not used ethernet nodes
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Series-to: u-boot
Series-version: 3
Series-changes: 3
- rebase patchset to current mainline commit
c0192950df
- update defconfig files
Series-changes: 2
- add patch which fixes Codingstyle errors in drivers/qe
- add patch which converts the mpc83xx based boards from
keymile to DM_ETH
Cover-letter:
powerpc, mpc83xx: add DM_ETH support
This patch series adds DM ethernet support for mpc83xx based
keymile boards.
Travis build:
END
Add platform data and a device structure for the spi device
present on am335x-icev2. This requires moving all omap3_spi
platform data structures and symbols to an omap3_spi.h so that
the board file can access them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The R5 SPL on J7200 SoCs will be limited to booting just the
MCU R5FSS0 R5F core in LockStep-mode at present, so add the
two required environment variables 'addr_mcur5f0_0load' and
'name_mcur5f0_0fw' that are needed by the R5 SPL early-boot
logic. The firmware name used is also different from that on
J721E SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
The J7200 SoCs have different number of remote processors, but reuse
the same environment settings as the J721E SoCs. The current env
variable rproc_fw_binaries is geared towards J721E SoCs and is
incorrect for J7200 SoCs. Please see the logic originally added in
commit 0b4ab9c9a7 ("env: ti: j721e-evm: Add support to boot rprocs
including R5Fs and DSPs").
Fix this by defining the DEFAULT_RPROCS macro appropriately using
the corresponding TARGET_EVM Kconfig symbol. This macro is used by
the 'rproc_fw_binaries' env variable in the common remoteproc env
header file k3_rproc.h.
The list of R5F cores to be started before loading and booting the
Linux kernel are as follows, and mainly comprises of the Main R5FSS0
cores in this order:
Main R5FSS0 (Split) Core0 : 2 /lib/firmware/j7200-main-r5f0_0-fw
Main R5FSS0 (Split) Core1 : 3 /lib/firmware/j7200-main-r5f0_1-fw
The MCU R5FSS0 is in LockStep mode and is expected to be booted by
R5 SPL, so it is not included in the list. The order of rprocs to
boot cannot be really modified as only the Main R5FSS0 cores are
involved and Core0 has to be booted first always before the
corresponding Core1.
Signed-off-by: Suman Anna <s-anna@ti.com>
The commit 316c927135 ("include: configs: j721e_evm: Add env variables
for mcu_r5fss0_core0 & main_r5fss0_core0") added four different new env
variables 'addr_mainr5f0_0load', 'name_mainr5f0_0fw', 'addr_mcur5f0_0load'
and 'name_mcur5f0_0fw' to the generic environment, but these are only
needed and used in R5 SPL for early-booting the MCU R5FSS0 and Main
R5FSS0 Core0 on J721E SoCs.
These are not really needed for A72 U-Boot, so limit the scope of
these variables only to R5 SPL. While at this, also fix the loadaddr
variable values to include the hex prefix like with other such env
variables.
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
The default rproc list currently used by A72 U-Boot to boot various
remote processors include the Main R5FSS0 (Split-mode) Core1, Main
R5FSS1 (LockStep mode) Core0 and the three DSPs. The Main R5FSS1 cluster
is configured for Split mode by default in the dts now, so add the
Main R5FSS1 Core1 (rproc #5) to the default rproc boot list. This
core is now booted after the Main R5FSS1 Core0 and before the DSPs.
The order of the rprocs to boot can always be changed at runtime if
desired by overwriting the 'rproc_fw_binaries' environment variable
at U-boot prompt. Note that the R5FSS Core1 cannot be booted before
its associated Core0.
Signed-off-by: Suman Anna <s-anna@ti.com>
Boot scripts for existing Espressobin Linux distributions, like OpenWRT,
expect that U-Boot set fdt_addr and kernel_addr envs. So add env aliases
from fdt_addr_r and kernel_addr_r values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
Current loadaddr is not writable on Espressobin and 'loadb' command cause
rebooting board. Marvell's U-Boot already set default loadaddr to value
0x06000000 [1] and after this change 'loadb' is working fine.
[1] - 0a5b159806
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
According to Marvell's U-Boot description [1] current env load addresses
overlaps with ATF RT services region and TEE. Because the ATF RT service
and TEE region is going to be marked as secure and can't be overwritten,
use different different addresses for envs.
[1] - 0a5b159806
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Add basic Marvell/Cavium OcteonTX/TX2 support (Suneel)
- Infrastructure changes to PCI uclass to support these SoC's (Suneel)
- Add PCI, MMC & watchdog driver drivers for OcteonTX/TX2 (Suneel)
- Increase CONFIG_SYS_MALLOC_F_LEN for qemu-x86 (Stefan)
Restrict the memory range available for image processing in the
"bootm" to 256 MiB so the kernel can access it and FDT or initrd are
not overwritten on ARM64.
Signed-off-by: Grygorii Tertychnyi <grygorii.tertychnyi@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The loading address is too close to the kernel address, so newer kernels
may overlap memory space, so loading the device tree may corrupt zImage.
This patch moves the fdt_addr_r to 0x14000000 which is also consistent
with guidance that the kernel be allocated 32MB. This places it
in the same place as the ramdisk, so this patch moves the ramdisk address
512KB after the fdt.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
We have a number of platforms that are a combination of a carrier board
and System-on-Module (SoM) that in turn allows for the board to have
different SoCs on it. In some cases, this is handled via board-specific
Kconfig options. In other cases we make use of
CONFIG_SYS_EXTRA_OPTIONS. This latter case however can lead to invalid
configurations as we will not in turn get options that in Kconfig are
selected by or depend on that setting.
To resolve this, make the SoC option a choice in Kconfig and make boards
depend on what they can support. This change opens us up for further
clean-ups in the cases where a single CONFIG_TARGET_xxx can support
different SoCs and today they do not, or do not cleanly do so.
Reported-by: Matt Porter <mporter@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Soeren Moch <smoch@web.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ian Ray <ian.ray@ge.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Cc: Simone CIANNI <simone.cianni@bticino.it>
Cc: Adam Ford <aford173@gmail.com>
Cc: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Parthiban Nallathambi <parthiban@linumiz.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Niel Fourie <lusus@denx.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Silvio Fricke <open-source@softing.de>
Tested-by: Matt Porter <mporter@konsulko.com> [colibri_imx6]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This patch adds support for all OcteonTX2 96xx/95xx
boards from Marvell.
For 96xx boards, use octeontx_96xx_defconfig and
for 95xx boards, use octeontx_95xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
This patch adds support for all OcteonTX 81xx/83xx
boards from Marvell.
For 81xx boards, use octeontx_81xx_defconfig and
for 83xx boards, use octeontx_83xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
CONFIG_CMD_RUN is set on by default in Kconfig.
Create xenguest_arm64_defconfig by using savedefconfig to avoid unnecessary
options.
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Total Compute is based on ARM architecture and has
the following features enabled in u-boot:
- PL011 UART
- PL180 MMC
- NOR Flash
- FIT image with Signature
- AVB
Signed-off-by: Usama Arif <usama.arif@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
