Internal registers in SPL are at address 0xd0000000 and in proper U-Boot at
address 0xf1000000. UART base address is located in internal registers.
Fix DEBUG_UART_BASE option to correct value for both SPL and proper U-Boot.
This change fixes hangup of proper U-Boot when it is trying to print
something via debug UART.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Stop parsing fixed-link in the MAC driver. Instead support only PHY mode
and let the fixed PHY driver handle the fixed-link case.
Enable CONFIG_PHY_FIXED for mvneta boards that need it: Turris Omnia and
ESPRESSObin.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the modern DM MDIO API for connecting PHY in the mvneta driver.
This requires enabling MVMDIO driver in several config files.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_ETHPRIME defines primary ethernet device and env variable $ethact
stores currently active ethernet device.
So there is no point to set ethact= in default environment. Instead set
CONFIG_ETHPRIME properly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Enable ext4 write support in Turris Omnia's defconfig. Some users find
it useful.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The state of the current DDR training code for Armada 38x is such that
we cannot be sure it will always train successfully - although after the
last change we were yet unable to find a board that failed DDR training,
from experience in the last 2 years we know that it is possible.
The experience also tells us that in many cases the board fails training
only sometimes, and after a reset the training is successful.
Enable the new option that makes the board reset itself on DDR training
failure immediately. Until now we called hang() in such a case, which
meant that the board was reset by the MCU after 120 seconds.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Apple SoCs have an integrated NVMe controller that isn't connected
over a PCIe bus. In preparation for adding support for this NVMe
controller, split out the PCI support into its own file. This file
is selected through a new CONFIG_NVME_PCI Kconfig option, so do
a wholesale replacement of CONFIG_NVME with CONFIG_NVME_PCI.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
On of the MiniPCIe ports on Turris Omnia is also a mSATA port. Whether
it works in SATA or PCIe mode is determined by a strapping pin, which
value is read from the MCU.
We already determine which type of card is connected when configuring
SerDeses.
But until now we left both SATA and PCIe port 0 nodes in device tree
enabled, and so the SATA driver is probed in U-Boot / Linux even if we
know there is no mSATA card, and similarly PCIe driver tries to link on
port 0 even if we know there is mSATA card, not a PCIe card.
Fixup device tree blob to disable SATA node if mSATA card is not
present, and to disable PCIe port 0 node if mSATA card is present.
Do this for U-Boot's DT blob before relocation and also for kernel DT
blob before booting.
This ensures that software does not try to use SATA or PCIe HW when
corresponding PHY is not configured.
Signed-off-by: Pali Rohár <pali@kernel.org>
[ refactored and fixed some issues ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
When booting over UART, sending U-Boot proper may take too much time and
MCU watchdog will reset the board before U-Boot proper is loaded.
Better disable MCU watchdog in SPL when booting over UART.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
PCIe-based NVMe SSD disks in M.2 2230/2242/2260 form-factor can be
connected to Turris Omnia mPCIe slot via passive M.2 <--> mPCIe adapter.
So enable PCIe NVMe drivers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Now that proper load and execution addresses are set in v1 kwbimage we
can use it for loading and booting U-Boot proper.
Use the new spl_parse_board_header() function to implement parsing the
kwbimage v1 header. Use information from this header to locate offset and
size of the U-Boot proper binary, instead of using the legacy U-Boot
header which is prepended to the U-Boot proper binary stored at fixed
offset. This has the advantage that we do not need to relay on legacy
U-Boot header anymore and therefore U-Boot proper binary can be stored at
any offset, as is the case when loading & booting U-Boot proper by
BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL
code anymore.
Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case
BootROM is used for loading and executing U-Boot proper. This reduces the
size of U-Boot's SPL image. By default these config options are enabled
and so BootROM loading is not used. In some cases BootROM reads from SPI
NOR at lower speed than U-Boot SPL. So people can decide whether they
want to have smaller SPL binary at the cost of slower boot.
Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO,
CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT,
CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and
CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply"
(which can be selectivelly turned off and causes booting via BootROM).
Options CONFIG_SYS_SPI_U_BOOT_OFFS,
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to
zero as they define the location where kwbimage header starts. It is the
location where BootROM expects start of the kwbimage from which it reads,
parses and executes SPL part. The same applies to option
CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one.
Update all config files to set correct values of these options and set
CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot
proper starts.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fixup SPI NOR partition nodes in Linux' device tree prior booting Linux.
Linux' devicetree does not contain "u-boot-env" partition and we do not
want to add it there because the address is different between stock
U-Boot and current upstream U-Boot.
Instead we add code that recreates partition nodes from scratch
according to how U-Boot sees them (which is defined in U-Boot's device
tree).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that the MTD subsystem properly supports OF partitions of a SPI NOR,
we can enable the MTD command and start using it instead of the
deprecated sf command.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit e2e95e5e25 ("spi: Update speed/mode on change") changed the
boot time on Turris Omnia from ~2.3s to over 8s, due to SPL loading main
U-Boot from SPI NOR at 1 MHz instead of 40 MHz.
This is because the SPL code passes the CONFIG_SF_DEFAULT_SPEED option
to spi_flash_probe(), and with the above commit spi_flash_probe() starts
prefering this parameter instead of the one specified in device-tree.
The proper solution here would probably be to fix the SF subsystem to
prefer the frequency specified in the device-tree, if it is present, but
I am not sure what else will be affected on other boards with such a
change. So until then we need a more simple fix.
Since the CONFIG_SF_DEFAULT_SPEED option is used by the code, put the
correct value there for Turris Omnia. Also put the correct value to
CONFIG_SF_DEFAULT_MODE and use 40 MHz when reading environment.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This command can be useful for U-Boot scripts.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Pali Rohár <pali@kernel.org>
Acked-by: Pali Rohár <pali@kernel.org>
This command can be sometimes used for debugging.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Pali Rohár <pali@kernel.org>
Acked-by: Pali Rohár <pali@kernel.org>
With this the date command is available on Turris Omnia.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Pali Rohár <pali@kernel.org>
Acked-by: Pali Rohár <pali@kernel.org>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
Update mvebu SPL boot selection mechanism for the move to driver model
usage by ensuring that the required driver support for SPI and MMC
booting is available in SPL when the respective boot method is
selected.
Previously, all mvebu boards selected a boot method (implicitly
MVEBU_SPL_BOOT_DEVICE_SPI for many) even if SPL booting wasn't used.
This changes mvebu boot method selection to depend on SPL usage which
resolves the issue with aarch64 boards which don't use SPL getting an
implicit boot device selection resulting in unmet dependencies. The
32-bit arm boards do use SPL, but I'm led to conclude that most aren't
intentionally using the MVEBU_SPL_BOOT_DEVICE selection since none have
SPL_DM_SPI enabled in their defconfig even though they still implicitly
select the SPI boot method.
This also results in the new addition of SPL_GPIO_SUPPORT to helios4.
The mainline dts for helios4 includes the cd-gpios entry for sdhci with
identical addresses as the clearfog dts. I don't have a helios4 board
to confirm, but based on the current source conclude that the board
itself is either wired to pull the signal low for eMMC, or the default
MMC boot isn't fully functional in mainline. In either case, as far as
I can tell, including the GPIO support will at least cause no
regression.
Tested on SolidRun ClearFog devices.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
