Set CONFIG_COUNTER_FREQUENCY according to COUNTER_FREQUENCY in
config header file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[trini: Re-run migration]
LS(1021/1012/1028/1043/1046/1088/2088), LX2160, LX2162
platforms are enabled with JR driver model.
removed sec_init() call from board files.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
This converts the following to Kconfig:
CONFIG_ETHPRIME
This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME
similar to other options that are not always set and control environment
variables.
Signed-off-by: Tom Rini <trini@konsulko.com>
Apple SoCs have an integrated NVMe controller that isn't connected
over a PCIe bus. In preparation for adding support for this NVMe
controller, split out the PCI support into its own file. This file
is selected through a new CONFIG_NVME_PCI Kconfig option, so do
a wholesale replacement of CONFIG_NVME with CONFIG_NVME_PCI.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Move the SATA options inside an 'if SATA' part, so they are grouped.
Fix the 'Complient' typo while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <trini@konsulko.com>
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR,
CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and
move these entries to defconfigs.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_MXC
CONFIG_SYS_I2C_MXC_I2C1
CONFIG_SYS_I2C_MXC_I2C2
CONFIG_SYS_I2C_MXC_I2C3
CONFIG_SYS_I2C_MXC_I2C4
Signed-off-by: Tom Rini <trini@konsulko.com>
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL. Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to
one or more symbols.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
The tsec driver now requires DM_MDIO when DM_ETH is enabled. To avoid
build errors, enable DM_MDIO in these boards' configs before we actually
add DM_MDIO support to tsec.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add Root Complex and Endpoint mode specific config entries, such that
it's feasible to enable the RC and/or EP mode driver indepently.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1021A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Now that we have added driver model support to the TSEC driver,
convert ls1021atwr board to use it.
This depends on previous DM series for ls1021atwr:
http://patchwork.ozlabs.org/patch/561855/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[Vladimir] Made the following changes:
- Added 'status = "disabled";' for all Ethernet ports in ls1021a.dtsi
- Fixed the confusion between the SGMII/TBI PCS for enet0 and enet1 -
a mistake ported over from Linux. Each SGMII PCS lies on the private
MDIO bus of the interface (and the RGMII enet2 has no SGMII PCS).
- Added CONFIG_DM_ETH to all ls1021atwr_* defconfigs
- Completely removed non-DM_ETH support from ls1021atwr
- Changed "compatible" string from "fsl,tsec-mdio" to "fsl,etsec2-mdio"
and from "fsl,tsec" to "fsl,etsec2" to match Linux
This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
