- added to keymile-common.h:
- bootcount support
- COMMAND HISTORY
- CONFIG_AUTO_COMPLETE
- CONFIG_SYS_FLASH_PROTECTION
- JFFS2 support
- CONFIG_VERSION_VARIABLE
- extracted common I2C settings for all boards
- common default environment settings summarized
Signed-off-by: Heiko Schocher <hs@denx.de>
The Nand flash was unable to read and write properly
due to Nand Chip Select (nCE) setup was in reverse
order. Also, increase the Nand time out value to 60.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
The serial boot dram extended/standard mode register was not
setup and was using default DRAM setup causing the U-boot was
unstable to boot up in serial mode.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
According to coldfire manual data timeout > address time out
also use correct macro to program XARB_CFG
Signed-off-by: Arun C <arunedarath@mistralsolutions.com>
nboot command currently does not skip bad blocks and gives read error when
loading image stored over bad block. With patch applied, nboot works as
expected:
Device 0 bad blocks:
00780000
014a0000
02000000
02cc0000
04aa0000
Loading from NAND 128MiB 3,3V 8-bit, offset 0x2c00000
Image Name: Linux-2.6.22-omap1
Created: 2008-11-20 23:44:32 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1052520 Bytes = 1 MB
Load Address: 10008000
Entry Point: 10008000
Skipping bad block 0x02cc0000
Automatic boot of image at addr 0x10400000 ...
...
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch fixes a problem spotted by Mikhail Zolotaryov on Sequoia with
the DDR2 configuration to only use one CS (rank). As this code is most
likely copied from the original Sequoia version, this error was copied
as well.
This patch also removes some dead code.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a problem spotted by Mikhail Zolotaryov on Sequoia with
the DDR2 configuration to only use one CS (rank). As this code is most
likely copied from the original Sequoia version, this error was copied
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Sequoia board schematics (DES0211_11_SCH_11.pdf, page 5, unit U1D)
specifies that BankSel#1 is not connected, while bootloader memory
configuration is (board/amcc/sequoia/sdram.c):
mtsdram(DDR0_10, 0x00000300);
i.e. both Chip Selects used - not correct.
If we change to correct value here:
mtsdram(DDR0_10, 0x00000100);
memory is accessible OK also.
Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Signed-off-by: Stefan Roese <sr@denx.de>
The routine assumed 4 bank SDRAMs, enhance to configure for 4 or 8
bank SDRAMs.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch makes sure the correct mask is applied when setting
the encryption and I2C bus 0 clock in SCCR.
Failing to do so may lead to ENCCM being 0 in which case I2C bus 0
won't function.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@aimvalley.nl>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The rtl8139 driver use pci_mem_to_phys. So it need PCI system memory
registration.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
We can built 'make sh7785lcr_32bit_config'. And add new command "pmb"
for this mode. This command changes PMB for using 512MB system memory.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Some register value was hardcoded for System memory size 128MB and
memory offset 0x08000000. This patch fixed the problem.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
It is necessary for some pci device driver.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Commit af1c2b84 added a generic phy support, with an ID of zero
and a 32 bit mask; meaning that it will match on any PHY ID.
The problem is that there is a test that checked if a matching
PHY was found, and if not, it printed the non-matching ID.
But since there will always be a match (on the generic PHY,
worst case), this test will never trip.
In the case of a misconfigured PHY address, or of a PHY that
isn't explicitly supported outside of the generic support,
you will never see the ID of 0xffffffff, or the ID of the
real (but unsupported) chip. It will silently fall through
onto the generic support.
This change makes that test useful again, and ensures that
the selection of generic PHY support doesn't happen without
some sort of notice. It also makes it explicitly clear that
the generic PHY must be last in the PHY table.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Fix typo in makefile which broke out of tree builds.
Also use expolicit "rm" instead of "ln -sf" which is known to be
unreliable.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
These were left in accidentally, and are not really useful unless the
code is as broken as it was when it was being developed.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Commit e1be0d25, "32bit BUg fix for DDR2 on 8572" prevented other
sdram_cfg bits (such as ecc and self_refresh_in_sleep) from being set.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Fix typo in makefile which broke out of tree builds.
Also use expolicit "rm" instead of "ln -sf" which is known to be
unreliable.
Signed-off-by: Wolfgang Denk <wd@denx.de>
add CONFIG_BOOTCOUNT_LIMIT feature for 8360 CPU.
The bootcounter uses 8 bytes from the muram,
because no other memory was found on this
CPU for the bootcount feature. So we must
correct the muram size in DTS before booting
Linux.
This feature is actual only implemented for
MPC8360, because not all 83xx CPU have qe,
and therefore no muram, which this feature
uses.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
old code implemented the QE_ENET10 errata only for Silicon
Revision 2.0. New code reads now the Silicon Revision
register and sets dependend on the Silicon Revision the
values as advised in the QE_ENET10 errata.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
it is possible that some board variants have different DDR II
RAM sizes. So we autodetect the size of the assembled RAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
