Bananapi-m2-plus has usb otg routed host with either EHCI0/OHCI0
sync the same from Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Enable USB_MUSB_GADGET which operate OTG in peripheral mode
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner H3 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
or MUSB controller.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner PHY USB code is now part of generic-phy framework,
so drop existing legacy handling like arch/arm/mach-sunxi.c
and related code areas.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner USB PHY handling can be done through driver-model
generic-phy so add the generic-phy ops to relevant places
on host and musb sunxi driver and enable them in respective
SOC's.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
The sunxi otg phy has a bug where it wrongly detects a high speed squelch
when reset on the root port gets de-asserted with a lo-speed device.
The workaround for this is to disable squelch detect before de-asserting
reset, and re-enabling it after the reset de-assert is done. Add a sunxi
specific phy function to allow the sunxi-musb glue to do this.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner PHY USB code is now part of generic-phy framework,
so use it in board_usb_cable_connected.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Sync sun4i-usb-phy bindings from Linux, since the
drivers/phy/allwinner/phy-sun4i-usb.c follow similar.
Sync changes from Linux with below commit:
"phy: sun4i-usb: add support for R40 USB PHY"
(sha1: f3d96f8d23d8e6d0b7642ee946b9b2ac3418fb4d)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner A23 has 2 USB PHY's and 0x04 has phy ctrl offset.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner A33 has 2 USB PHY's and 0x10 has phy ctrl offset.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Add PHY configs for Allwinner A10/A13/A20 which are SUN4I.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Unlike, other Allwinner SUN4I Phy supporting SOC, A83T has
2 USB PHY's and second one is HSIC. So phy control need to
configure to handle these HSIC and SIDDQ requirement.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
ID and VBUS detection code require when musb changing
between Host and/or Peripheral modes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
USB PHY implementation for Allwinner SOC's can be handling
in to single driver with different phy configs.
This driver handle all Allwinner USB PHY's start from 4I to
50I(except 9I). Currently added A64 compatibility more will
add in next coming patches.
Current implementation is unable to get pinctrl, clock and reset
details from DT since the dm code on these will add it future.
Driver named as phy-sun4i-usb.c since the same PHY logic
work for all Allwinner SOC's start from 4I to A64 except 9I
with different phy configurations.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Like other Allwinner SoC, the H3/H5/A64 is missing the config register
from the musb hardware block. Use a known working value for it
like other SoC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Clock gating bits on H43/H5 were wrong, fix them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Add OTG device clkgate and reset for H3/H5 through driver_data.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
clock gating bits on a64 are different than H3_H5, so fixed
only required bits on clock_sun6i.h.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Unlike other Allwinner SOC's H3/H5/V3s OTG support 4 endpoints
with relevant fifo configs, rest all have 5 endpoints.
So add the fifo configs and defer them based on driver_data.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Filling musb_hdrc pdata using structure will unnecessary
add extra ifdefs, so fill them inside probe call for
better code understanding and get rid ifdefs using
devicetree compatible.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
- add proper macros for musb_config members
- use bool 'true' for multipoint and dyn_fifo instead of numerical 1
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Move struct sunxi_ccm_reg pointer to private structure
so-that accessing ccm reg base become more proper way
and avoid local initialization in each function.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
This reverts commit 819f1e081c.
This check was introduced in order to cope with the size limitation we had
when we were still using the raw environment in MMC. However, this
introduces padding as well, which can result in an overly huge binary if
one wants to flash the environment to some other location.
Since we now have a FAT-based environment, this check is not so useful
anymore, so we can just drop it.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Måns Rullgård <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for DEBUG_UART on ARC devboards
This required us to do 2 things:
1) Insert a call to debug_uart_init() in early boot code
2) Convert serial_arc to Kconfig
Once both items above are done we just patched defconfigs.
Some minor fixes for the Raspberry Pi:
- Fix SD writes on new sdhost controller
- Sanitize default load addresses, allowing for better payload placement
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=te7/
-----END PGP SIGNATURE-----
Merge tag 'signed-rpi-next' of git://github.com/agraf/u-boot
Patch queue for rpi - 2018-05-24
Some minor fixes for the Raspberry Pi:
- Fix SD writes on new sdhost controller
- Sanitize default load addresses, allowing for better payload placement
The debug UART is intended for use very early in U-Boot to debug
problems before serial drivers are up.
Call debug_uart_init right before board_init_f.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As of Linux 4.16, a multiplatform AArch64 kernel with our distro config
takes 26M. The current space reservation leaves only 17M for the kernel
and if it goes over it, the initrd gets overwritten when loading the
kernel from the filesystem.
A similar problem happens on ARMv7 with the DTBs taken from the
downstream Raspberry Pi foundation kernel. I guess they compile them
with DT overlay support enabled which grows them just enough.
Fix both of these problems by rewriting the memory map, which now allows
kernels to be up to 36M and DTBs up to 1M. Also the comment block was
kind of obsolete ever since the introduction of AArch64 support and the
firmware-loaded DTB doesn't get placed at 0x100 anymore either, so that
is fixed as well.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add support for loading U-Boot and optionally FDT from a fitImage
in SPL by using the full fitImage support from U-Boot. While we do
have limited SPL loading support in SPL with a small footprint, it
is missing a lot of important features, like checking signatures.
This support has all the fitImage features, while the footprint is
obviously larger.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add missing CC and LDSHARED variables to the Makefile to pass the
correct C compiler and linker path to the build of _libfdt.so .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The script decodecode can be used to disassemble the 'Code:' line written
when an exception occurs.
The script is copied from Linux v4.16.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If an exception occurs in a loaded image and the relocation offset is
unknown, it is helful to know the instructions pointed to by the
program counter. This patch adds the missing output.
A possible output is:
Code: e1c560d0 e12fff1e e120077b e12fff1e (e7f7defb)
The parentheses indicate the instruction causing the exception.
The output can be disassembled using the decodecode script provided
by the Linux kernel project.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Following the conversion of the SPDX license tags, a number of files
compiled with -pedantic now generate warnings similar to the following
for using C99-style '//' comments in ISO C90 code:
tools/gen_eth_addr.c:1:1: warning: C++ style comments are not allowed in ISO C90
// SPDX-License-Identifier: GPL-2.0+
^
The SPDX comment-style change means that these files have adopted C99,
so need to change the language-standard to --std=gnu99 or --std=gnu11
to let the compiler know this.
As we now require GCC 6 or newer for the cross-compiler, the project has
implicitly moved the project to GNU11: let older GCC versions on various
Linux distros know to treat our host tools as GNU11 as well.
References: commit 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MMC is not initialized in SPL, so it cannot load u-boot.img
preventing boot from MMC.
Also driver specific functions are guarded with generic
configuration options which leads to build failures when device
driver is not enabled in config. Fix that by using driver
specific defines.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Stefano Babic <sbabic@denx.de>
Just add IH_TYPE_STANDALONE to fit_get_image_type_property().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
These functions may be needed in SPL, so add empty variants of them
if CONFIG_SPL_FIT_PRINT is disabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename CONFIG_FIT_SPL_PRINT to CONFIG_SPL_FIT_PRINT and add Kconfig
entry for it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for loading FPGA into the SPL fitImage support. The
mechanism is flexible and allows user to override the actual
function for loading the FPGA itself. This is because on some
systems, the FPGA must be programmed to allow DRAM access, so
loading the full fitImage may not be possible if it contains
the bitstream. Instead, the spl_load_fpga_image() provides all
the tools to load the bitstream in parts while programming it
into the FPGA.
Signed-off-by: Marek Vasut <marex@denx.de>
[trini: Don't always have a branch to print out type]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a command to manipulate the bootcounter. This is useful if you can
run device recovery from inside U-Boot and need to reset the bootcounter
after executing that process as part of altbootcmd.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
