The "Mode :" line is the only one in "mmc info" output that has a
space in front of the colon. Drop the space to make it consistent
with the rest of the output, e.g.:
=> mmc dev 1 ; mmc info
switch to partitions #0, OK
mmc1 is current device
Device: sd@ee160000
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Bus Speed: 50000000
Mode : SD High Speed (50MHz)
^------------------------------ Remove this space
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
Bus Width: 1-bit
Erase Group Size: 512 Bytes
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
CC: Tom Rini <trini@konsulko.com>
According to the R-Car Gen3 Hardware Manual Rev 1.50 of Nov 30, 2018, the
TX clock internal delay mode isn't supported on R-Car E3 (r8a77990) or D3
(r8a77995).
Avoid setting the APSR:TDM bit on these SoCs. Moreover, only set APSR:TDM
when the DT explicitly specifies RGMII ID or TXID mode instead of setting
it unconditionally when the PHY link speed is 1000 Mbit/s.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
To assure the pins on R-Car Gen3 SoCs are configured correctly, always
select pin control drivers on Gen3 SoCs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This function is now replaced by common pin controller GPIO configuration
functionality, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Cc: Eugeniu Rosca <roscaeugeniu@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick DELAUNAY <patrick.delaunay@st.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
Switch to generic pin controller API for configuring pins as GPIOs
instead of using the ad-hoc call into the R-Car PFC driver. Moreover,
add .free() implementation for the GPIO controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Cc: Eugeniu Rosca <roscaeugeniu@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick DELAUNAY <patrick.delaunay@st.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
Implement the gpio_request_enable/gpio_disable_free callbacks to let
the GPIO driver call the pin control framework and let it reconfigure
pins as GPIOs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Cc: Eugeniu Rosca <roscaeugeniu@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick DELAUNAY <patrick.delaunay@st.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
Add missing cfg->type = PINMUX_TYPE_GPIO upon successfully setting pin
as a GPIO to retain the pin configuration information.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Cc: Eugeniu Rosca <roscaeugeniu@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick DELAUNAY <patrick.delaunay@st.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
Add callback to configure, and de-configure, pin as a GPIO on the
pin controller side. This matches similar functionality in Linux
and aims to replace the ad-hoc implementations present in U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Cc: Eugeniu Rosca <roscaeugeniu@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick DELAUNAY <patrick.delaunay@st.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
The ATF can pass additional information via the first four registers,
x0...x3. The R-Car Gen3 with mainline ATF, register x1 contains pointer
to a device tree with platform information. Parse this device tree and
extract DRAM size information from it. This is useful on systems where
the DRAM size can vary between configurations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
clk_get_rate may return -ENODEV if the clock isn't valid.
Also, make the error cases go through a single path.
Fixes: ff8eee0330 ("cmd: clk: Add trivial implementation of clock dump
for DM")
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
There are a few functions defined in the header file, but they are
not referenced by any Davinci code. In order to make a general
function in the future with static function declarations, this
patch will remove the references all together.
Signed-off-by: Adam Ford <aford173@gmail.com>
There is a delay function that was commented out. This patch
re-enables it, because it will be needed for da850 ohci support.
Signed-off-by: Adam Ford <aford173@gmail.com>
The btrfs implementation methods .ls(), .size() and .read() returns 1 on
failure, but the command handlers expect values <0 on failure.
For example if given a nonexistent path, the load command currently
returns success, and hush scripting does not work.
Fix this by setting return values of these methods to -1 instead of 1 on
failure.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
When CROSS_BUILD_TOOLS is set, set HOSTCFLAGS to CFLAGS otherwise CC
will be used with HOSTCFLAGS which seems wrong
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
The card detect pin was incorrectly using IRQ_TYPE_LEVEL_LOW
instead of GPIO_ACTIVE_LOW when reading the state of the CD pin.
Without this patch, MMC1 won't be detected.
This is the same patch submitted to linux-omap, but I was hoping
to get it applied to U-Boot without having to wait for the
linux adoption and then backporting.
Fixes: 5448ff33f2 ("ARM: DTS: Resync Logic PD SOM-LV 37xx
devkit with Linux 4.18-RC4")
Signed-off-by: Adam Ford <aford173@gmail.com>
The DM* family of SOCs is no longer supported. We now support the
omap-l138 lcdk board and Lego EV3 platform. Reflect those changes
in the README.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Add am335x-pocketbeagle to CONFIG_OF_LIST in am335x_evm_defconfig.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add device-tree files from linux 5.1-rc7 needed to complete support
for PocketBeagle.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Transition to the IOPAD macros as used in Linux in which the pin mux
mode is specified using a dedicated parameter while also dropping the
related MUX_MODEx macros that are no longer needed. This transition
will allow us to keep both Linux and U-Boot DTS in sync more easily.
While at it also align the file name of the include file itself and
update any references accordingly.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
- at91sam9g20-taurus.dts: use labels
- cleanup taurus port to compile clean with
current mainline again. SPL has no serial
output anymore, so it fits into SRAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
TI-SCI firmware will only respond to messages when the
TI_SCI_FLAG_REQ_ACK_ON_PROCESSED flag is set. Most messages
already do this, set this for the ones that do not.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Alejandro Hernandez <ajhernandez@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
commit 95f4bbd581 ("lib: fdt: Allow LZO and GZIP DT compression in U-Boot")
introduced Kconfig option for gzip in U-Boot, but help text
says gzip for SPL, which is wrong. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
The existing comments where confusing read and write. The comment for
fs_write() had:
"@addr: The address to read into"
So let's rework the comments and format them in Sphinx style.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Switch from using the high priority DMSC transmit message queue used
by the secure R5 MCU island boot context to the low priority message
queue. While the change in priority is irrelevant for the current boot
architecture it however gives us access to a deeper message queue that
will allow us to buffer more messages. This is an important aspect when
sending several messages without requesting and waiting for a response
in a row which is a communication scheme used during core shutdown for
example. See AM654 TISCI User Guide for additional details.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
In commit ad6054f1fe where support for the
Sancloud BeagleBone Enhanced (BBE) was added, new conditional
configuration of either MII pin muxing or RGMII pin muxing is done
depending on the board type. However, the old call to set up MII pin
muxing was not removed.
This may result in misconfiguration of the pin muxing for the BBE or
duplicate configuration for other boards and so we remove this obsolete
call.
Signed-off-by: Paul Barker <paul.barker@sancloud.co.uk>
Restart operation never exists and reset operation never
makes the watchdog expire immediately but expire_now operation
does.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Upcoming sysfw (2019.03) will not open the channelized firewalls during
init, it only going to do so in response to the channel configuration
message.
Remove the channel state checks done before the channel configuration and
move it after the configuration for warning purposes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
An earlier commit converted the TISCI receive timeouts to be specified
in ms rather than us however it failed to take this change into account
when passing the actual timeout to be used when invoking the mailbox
receive API. This leads to the actual timeout to be 1,000 times shorter
than expected and as a result certain TISCI operations would fail.
Fix the issue by converting the timeout declared in ms to us on the fly
as expected by the respective API.
Fixes: fd6b40b1ba ("firmware: ti_sci: Add support for NAVSS resource management")
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the mmc maintainer from Jaehoon to me.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Marek Vasut <marex@denx.de>
Currently packet data is wrongly extracted when metadata is NULL.
Fix it and negate the if check.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
This pull request provides error fixes for the handling of GPT partitions
and for the UEFI subsystem.
-----BEGIN PGP SIGNATURE-----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=GUpA
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc2
This pull request provides error fixes for the handling of GPT partitions
and for the UEFI subsystem.
This options will be enabled by default by CZ.NIC shipped U-Boot. Enable
them in defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for the gpio command and driver for the I2C connected
pca9538 controller, to be able to determine if SFP module is present in
the Turris Omnia router.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The twsi_wait function reads the control register for interrupt flag,
and if interrupt flag is present, it immediately reads status register.
On our device this sometimes causes bad value being read from status
register, as if the value was not yet updated.
My theory is that the controller does approximately this:
1. sets interrupt flag in control register,
2. sets the value of status register,
3. causes an interrupt
In U-Boot we do not use interrupts, so I think that it is possible that
sometimes the status register in the twsi_wait function is read between
points 1 and 2.
The bug does not appear if I add a small delay before reading status
register.
Wait 100ns (which in U-Boot currently means 1 us, because ndelay(i)
function calls udelay(DIV_ROUND_UP(i, 1000))) before reading the status
register.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
There is a Factory RESET button on the back side of the Turris Omnia
router. When user presses this button before powering the device up and
keeps it pressed, the microcontroller prevents the main CPU from booting
and counts how long the RESET button is being pressed (and indicates
this by lighting up front LEDs).
The idea behind this is that the user can boot the device into several
Factory RESET modes.
This patch adds support for U-Boot to read into which Factory RESET mode
the user booted the device. The value is an integer stored into the
omnia_reset environment variable. It is 0 if the button was not pressed
at all during power up, otherwise it is the number identifying the
Factory RESET mode.
This patch also changes bootcmd to a special hardcoded value if Factory
RESET button was pressed during device powerup. This special bootcmd
value sets the colors of all the LEDs on the front panel to green and
then tries to load the rescue image from the SPI flash memory and boot
it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The regdomain environment variable is set according to value read from
EEPROM. This has to be done in board_late_init, after the environment
variables are read from SPI. Select CONFIG_BOARD_LATE_INIT in Kconfig
for the Turris Omnia target.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Since board watchdog is now unified and not handled in board files,
remove the unnecessary includes.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Unify the way how Omnia and Mox print board information (RAM size and
serial number).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Refactor RAM size reading from EEPROM in preparation for next patch.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This driver is required for Turris Omnia to read ethernet addresses.
Move the dependency from turris_omnia_defconfig to Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Refactor code which accesses the microcontroller and EEPROM via I2C.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
If SCSI is enabled, U-Boot should try to boot also from SCSI device on
Turris Omnia.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The I2C dependencies are defined in include/configs/turris_omnia.h,
because Turris Omnia won't boot correctly without I2C support.
Move these dependencies to Kconfig, so that they are selected if Turris
Omnia is selected as target.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
