Some host controllers need addidional initialization after ehci_reset()
In non-dm implementation it is possible to use CONFIG_EHCI_HCD_INIT_AFTER_RESET.
This patch adds similar option to ehci drivers using dm.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
We have a separate compatible for almost each SoC. Add one for the A83T.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We have a separate compatible for almost each SoC. Add one for the A83T.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The 2nd usb controller on sun4i/sun7i has its base address 0x8000
bytes from the 1st one, rather then 0x1000. Also the ahb clk gates
are interleaved with the ohci clk-gates introducing a hole between
the clks for usb1 and usb2.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add test into xhci_submit_control_message for usb requesttype in USB
vendor request being of standardized type. This fixes detection of
certain USB fixes, for example Ethernet, USB 3.0 port. Non standardized
requesttype in USB vendor request will be ignored.
Signed-off-by: Ted Chen <tedchen@realtek.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
When 'usb start' is used, block devices are created for any USB flash sticks
and disks, etc. When 'usb stop' is used, these block devices are currently
not removed.
We don't want old block devices hanging around since they can still be
visible to U-Boot. Therefore, when USB is shut down, remove and unbind all
the block devices created by the USB subsystem.
Possibly we should unbind all devices which don't cause problems by being
unbound. Most likely we can remove everything except USB controllers, hubs
and emulators. We can consider that later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
For the case where an external VBUS is used, we should enable the external
VBUS comparator in the driver. This would prevent an unnecessary overcurrent
error which would then disable the host port.
The overcurrent condition was happening on the SoCFPGA Cyclone5 devkit, thus
USB was not working on the devkit. This patch fixes that problem.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Fix the following warning on aarch64 introduced by using p2v/v2p
functions in the code:
In file included from ./arch/arm/include/asm/byteorder.h:29:0,
from include/compiler.h:125,
from include/image.h:19,
from include/common.h:88,
from drivers/usb/host/ehci-hcd.c:10:
drivers/usb/host/ehci-hcd.c: In function ‘ehci_td_buffer’:
drivers/usb/host/ehci-hcd.c:250:49: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
td->qt_buffer[idx] = cpu_to_hc32(virt_to_phys((void *)addr));
^
include/linux/byteorder/little_endian.h:34:51: note: in definition of macro ‘__cpu_to_le32’
#define __cpu_to_le32(x) ((__force __le32)(__u32)(x))
^
drivers/usb/host/ehci-hcd.c:250:24: note: in expansion of macro ‘cpu_to_hc32’
td->qt_buffer[idx] = cpu_to_hc32(virt_to_phys((void *)addr));
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Rini <trini@konsulko.com>
Add explicit cpu_to_be32()/be32_to_cpu() conversion to BE EHCI I/O
accessors to align them with their LE counterpart. No functional
change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
If the USB EHCI is configured for little endian MMIO, make sure to
clear the USBMODE_BE flag from the USBMODE register.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Certain processor architectures, like MIPS, require that the USB
structures and transfer buffers are passed with their PA to the
USB controller. If VA is passed, the USB will not work. Add the
necessary virt_to_phys() calls into the USB EHCI code to make it
work.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Some architectures, like MIPS, require remapping of the registers.
Add the map_physmem() call to handle it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Due to introducing the new PLLB clock handle functions,
use these functions to clean up the PLLB enable/disable code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Heiko Schocher <hs@denx.de>
Due to introducing the new UTMI PLL clock handle functions,
use these function to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the new peripheral clock handle functions,
use these functions to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
[fixup for missing clk.h in at91_emac.c]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Now, all this driver does can be covered by the generic EHCI driver
(drivers/usb/host/ehci-generic.c). UniPhier SoCs have switched to
use it. Delete this driver rather than bothering to convert it to
Driver Model.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
This driver is designed in a generic manner, so clocks should be
handled genericly as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use existing library function to poll bit(s).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Add a compatible string to allow this to be specified in the device tree
if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
USB protocol allows for 16 IN and 16 OUT endpoints (USB 2.0 Spec,
8.3.2.2 Endpoint Field). A function may have an EP 1 for both IN and OUT,
so these two should be kept separate. As EPs are either BULK or INTERRUPT
(or ISO), it is fine to have one array per direction for all transfer
types (also see e236519b73).
USB device address is 7 bits, so a bus may have more than 16 devices.
Check the device number, as the DWC2 driver only supports BULK/ISO for
the first 16 devices.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
CSPLITs for INTERRUPT transactions have to be scheduled in each microframe
following the SSPLIT. INTERRUPT transfers are executed in the next even/
odd microframe depending on the HCCHAR_ODDFRM flag.
As there are no handshakes for INTERRUPT SSPLITs the SSPLIT may have
failed (transport error) without the error being detected by the host
driver. If the last CSPLIT is not received within 4 microframes after the
SSPLIT there was a transaction error and the complete transaction has
to be restarted.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
In contrast to non-SPLIT transfers each transaction has to be submitted
as an individual chunk.
The transaction state machine proceeds from SSPLIT to CSPLIT if the ACK
flag is set. CSPLIT has to be repeated while NYET is set.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
The split register setting is used for both SSPLIT and CSPLIT transactions,
the bit for CSPLIT has to be set seperately.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Split the movement of data between CPU and Host Controller from the
status handling and tracking of transfer progress.
This will also simplify adding of SPLIT transaction support.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
A transfer is completed if the XFERCOMP flag is set, irrespective of the
ACK flag. BULK OUT transfers to some HS devices complete without having
the ACK flag set, which signal the devices has responded with an NYET
to the transfer (PING protocol).
The new behaviour matches the Linux kernel minus any PING protocol.
Also see 5966defabdcc (usb: dwc2: fix bulk transfers)
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Fix two errors in transfer len calculation, move loop invariant code out
of loop.
If xfer_len is equal to CONFIG_DWC2_MAX_TRANSFER_SIZE (or slightly
smaller), the xfer_len will be to large, e.g.:
xfer_len = MAX_TRANSFER_SIZE = 65535
max packet size = 512
=> num_packets = 128
=> IN xfer_len = 65536
For OUT transactions larger than (65536 - mps) bytes, the xfer_len
determination is quite awkward, it is only correct due to:
- max_packet_size for control/bulk/interrupt is required to be
power-of-two.
- (CONFIG_DWC2_MAX_TRANSFER_SIZE + 1) % max-packet-size is zero
for all allowed (2^3 ... 2^9) packet sizes
As the max xfer len is loop invariant, it can be moved out of the loop.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Add board_usb_phy_mode weak function on similar lines to ehci-mx6.
However since Vybrid USB does not have a true OTG, make this weak
functon just return 0. The function is supposed to be implemented
by the individual boards using a GPIO for providing the OTG pin
functionality.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
The current ehci-vf USB driver for Vybrid hardcodes the USB host
and client functionality. Remove this.
Reported-by: Santhosh Kumar Janardhanam <santhosh.kj@hcl.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Convert this driver to use the new driver model PCI API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Most driver model PCI functions have a dm_ prefix. At some point, when the
old code is converted to driver model and the old functions are removed, we
will drop that prefix.
For consistency, we should use the dm_ prefix for all driver model
functions. Update pci_get_bdf() accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Start split and complete split tokens need the hub address and the
downstream port of the first HS hub (device view).
The core of the function was duplicated in both host/ehci_hcd and
musb-new/usb-compat.h.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
flush_dcache_range may access data after priv->aligned_buffer end if
len > DWC2_DATA_BUF_SIZE.
memcpy may access data after buffer end if done > 0
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
This driver is meant to be used with any OHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
With the old order of initialization the hcor pointer has been setup to
the same address as Exynos EHCI base address (0x12110000 instead of
0x12110010).
Such behaviour was caused by reading value of 0 instead of 0x10 from EHCI
HCCPBASE register without doing proper clock initialization before.
To fix this problem hcor initialization has been moved after USB PHY setup.
Now ehci_readl(&ctx->hcd->cr_capbase) returns correct value.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
This patch removes unsued function usb_phy_reset, rather common function
dwc3_phy_reset is used.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
As per dwc3 databook, delay is required before taking the core out of reset.
This delay is required so that the PHY are stable, and then we can take core
out of reset.
Reference is taken from linux dwc3 code, file: drivers/usb/dwc3/core.c.
Signed-off-by: Sriram Dash <sriram.dash@freescale.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
This driver is meant to be used with any EHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
The DM entry should be unique, otherwise it will collide with other
drivers. Fix this by assigning the driver a more unique name than
usb_ehci.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Simon Glass <sjg@chromium.org>
The driver does "return 0" in function with void type.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Fix the following build break:
drivers/usb/host/xhci-omap.c:35:5: error: ‘board_usb_init’ aliased to external symbol ‘__board_usb_init’
int board_usb_init(int index, enum usb_init_type init)
^
Signed-off-by: Felipe Balbi <balbi@ti.com>
Each scan of the USB bus may return different results. Existing driver-model
devices are reused when found, but if a device no longer exists it will stay
around, de-activated, but bound.
Detect these devices and remove them after the scan completes.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function should not be used with driver model. While there are users
of USB Ethernet that use driver model for USB but not Ethernet, we have
to keep it around. Add a comment to that effect.
Signed-off-by: Simon Glass <sjg@chromium.org>
