This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
While we have long since migrated to CONFIG_SYS_GENERIC_BOARD being
enabled, we had just a few places left that still referenced or defined
it. Update.
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit enables CONFIG_BLK and removes USB_STORAGE which is awaiting
proper implementation for current U-Boot interfaces. Additionally the
console selection is now handled by Kconfig and no longer needs to be in
the config header. CONFIG_SYS_MALLOC_F_LEN=0x2000 was added to sync with
other boards. CONFIG_SPL_BLK and CONFIG_SPL_DM_MMC are disabled because
they currently do not allow the OMAP3-EVM (OMAP34XX) to actually boot.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Since commit bfea69ad27 ("stm32f7: sdram: correct sdram
configuration as per micron sdram"), CONFIG_SYS_RAM_FREQ_DIV
flag is no more used, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Remove CONFIG_CMD_CACHE from include/configs/stm32f746-disco.h
and enable it in stm32f746-disco_defconfig
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Enable instruction and data caches.
Fix boot_sd command as since commit d409c96216 ("armv7m: disable
icache before linux booting"), instruction cache is automatically
disable before linux booting. "icache off" from boot_sd command
becomes useless, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since commit aa5e3e22f4 ("board: stm32: switch to DM STM32 timer")
SYS_CLK_FREQ is useless, remove it from stm32f4 and stm32f7 boards.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use gd->bd->bi_dram[0].start initialized from DT instead of using
hardcoded CONFIG_SYS_SDRAM_BASE from config file.
Remove unused CONFIG_SYS_RAM_BASE and CONFIG_SYS_SDRAM_BASE defines.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Move some configuration #defines that do not apply to other bcmstb
boards from bcmstb.h to bcm7445.h.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Move the contents of prior_stage.h into bcmstb.h to prevent a build
failure when bcmstb.h is #include'ed before the asm/arch symbolic link
is present.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Update all A83T devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 221cb9fd2ee3042689fe0e6613d0f34eb46a5af6
Author: Mylène Josserand <mylene.josserand@bootlin.com>
Date: Fri May 4 21:05:44 2018 +0200
ARM: dts: sun8i: Add enable-method for SMP support for the A83T SoC
Note: bananapi-m3 and cubietruck-plus board dts files has
usb_otg enabled in U-Boot which were not present in Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add a uclass for AXI (Advanced eXtensible Interface) busses, and a
driver for the gdsys IHS AXI bus on IHS FPGAs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
This update adds PPC64 ELF V1 ABI support to bootelf for both the
program header and section header options. Elf64 support was already
present for the program header option, but it was not handling the
PPC64 ELF V1 ABI case. For the PPC64 ELF V1 ABI, the e_entry field of
the elf header must be treated as function descriptor pointer instead
of a function address. The first doubleword of the function descriptor
is the function's entry address.
Signed-off-by: Rob Bracero <robbracero@gmail.com>
[trini: Fix whitespace issues]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch save common LED property "default-state" value
in post bind of LED uclass.
The configuration for this default state is only performed when
led_default_state() is called;
It can be called in your board_init()
or it could added in init_sequence_r[] in future.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The 16 char ethernet name size is inadequate to hold the name of ethernet
name "DPMAC17@rgmii-id", which is a valid name in LX2160AQDS/LX2160ARDB.
Therefore, increase the name string size to 20 chars.
Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Ioana Ciocoi Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This introduces two new APIs dm_pci_find_capability() and
dm_pci_find_ext_capability() to get PCI capability address and
PCI express extended capability address for a given PCI device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently we don't have a complete list of capability and extended
capability ids. This adds them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present all emulated sandbox pci devices must be present in the
device tree in order to be used. The real world pci uclass driver
supports pci device driver matching, and we should add such support
on sandbox too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We don't have the live-tree version of fdtdec_get_pci_vendev().
This adds the API.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Correct typos in the comment block of uclass_first/next_device_check().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These macros should not be put in the generic pci.h header file.
Since they are not referenced anywhere, remove them completely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This add the initial support of the broadcom reference
board bcm968380gerg with a bcm68380 SoC.
This board has 512 MB of RAM, 128 MB of flash (nand),
2 USB port, 1 UART, 4 ethernet ports and BCM43217 (wifi).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This adds the initial support of the Broadcom BCM6838 SoC familly,
only cpu, dram, uart and leds are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The only platform left for the AU1x00 SoCs was the pb1x00 platform, an
apparent clone of the dbau1x00 platform. As pb1x00 had no listed
maintainer I am assuming that it is also orphaned. Remove this platform
and then remove the unused SoC support.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This platform has been marked as orphan since June of 2016 and should
have been removed some time ago. Do so now.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
CONFIG_MTD_DEVICE is required for the mtdparts command and but it is missing from the mvebu_armada-37xx.h
CONFIG_MTD_PARTITIONS is needed for the ubi support. Some of the Marvell based devices may require this as well.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GP24 and SBx81GT24 cards
cards collectively referred to as SBx81LIFXCAT in u-boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Now that there is DM support in the RTC_MV driver update board configs
to use it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
To aid in migrating CONFIG_RTC_MV to Kconfig move the definition of it
from mv-plug-common.h to the board config headers that nest it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This allows selection of the boot device at build time without source
code modification.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Use MVEBU_SPL_BOOT_DEVICE_* to select between SPI and MMC, instead of
board specific symbols. This commit enables the boot device selection
menu to all mvebu platforms, but it is only effective on Turris Omnia
and gdsys Controlcenter DC platforms. A following commit will enable
boot selection for other platforms.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Add dummy functions when CONFIG_POWER_DOMAIN not defined.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch moves the the config SYS_MALLOC_LEN to
Kconfig. It will be just for Zynq arch and to do
will be for all other archs.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to have the same setting in subsequent config if we
can have it only once in shared.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This change is necessary to allow booting the Odroid XU3 from SD card
after enabling the DM_MMC support.
After this change the SD card mmc IP block is correctly enumerated as mmc2
(and not as mmc1 as in the legacy code).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Several boards do not use the default UART3, so they do a check
for ifdef CONFIG_SPL_BUILD and enable the pointer for
CONFIG_SYS_NS16550_COMx to point to OMAP34XX_UARTx.
Let's consoldate this all into one place, and remove them from the
individual boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add clk_valid() to check for optional clocks are valid.
Call clk_valid() in test/dm/clk.c and add relevant test routine to
sandbox clk tests.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present each entry has an offset within its parent section. This is
useful for figuring out how entries relate to one another. However it
is sometimes necessary to locate an entry within an image, regardless
of which sections it is nested inside.
Add a new 'image-pos' property to provide this information. Also add
some documentation for the -u option binman provides, which updates the
device tree with final entry information.
Since the image position is a better symbol to use for the position of
U-Boot as obtained by SPL, update the SPL symbols to use this instead of
offset, which might be incorrect if hierarchical sections are used.
Signed-off-by: Simon Glass <sjg@chromium.org>
After some thought, I believe there is an unfortunate naming flaw in
binman. Entries have a position and size, but now that we support
hierarchical sections it is unclear whether a position should be an
absolute position within the image, or a relative position within its
parent section.
At present 'position' actually means the relative position. This indicates
a need for an 'image position' for code that wants to find the location of
an entry without having to do calculations back through parents to
discover this image position.
A better name for the current 'position' or 'pos' is 'offset'. It is not
always an absolute position, but it is always an offset from its parent
offset.
It is unfortunate to rename this concept now, 18 months after binman was
introduced. However I believe it is the right thing to do. The impact is
mostly limited to binman itself and a few changes to in-tree users to
binman:
tegra
sunxi
x86
The change makes old binman definitions (e.g. downstream or out-of-tree)
incompatible if they use the 'pos = <...>' property. Later work will
adjust binman to generate an error when it is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
That's a set of prety minor changes and fixes for ARC.
Among them:
* Improvement in CREG GPIO driver used on ARC dev boards
that allow us to re-use the driver for SPI's chip select
* Enable SPI-flsh on AXS10x boards which allows to update
U-Boot binary that gets loaded by boot-ROM
* Fix accommodating always utilized unaligned access by
GCC for ARC starting from 8.1.0
There was an EHCI endian accessor issue. Now it's fixed by commit
9829ce2ff2 ("usb: ehci: Fix accessors for big-endian platforms and
descriptors"). Revert commit e6a727fffe ("powerpc/T104xRDB: Fix
endian access issue on EHCI intinalization"). On T104x platform,
USB EHCI register use little endian.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
There was an EHCI endian accessor issue. Now it's fixed by commit
9829ce2ff2 ("usb: ehci: Fix accessors for big-endian platforms and
descriptors"). Revert commit 0f2296bab1 ("powerpc/p1_p2_rdb_pc:
Fix endian access issue on EHCI intinalization"). On P1 P2 platforms,
USB EHCI register use little endian.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Now number of PHY on Allwinner is handling via dt data,
drivers at phy/allwinner/phy-sun4i-usb.c
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner H6 is a new SoC from Allwinner features USB3 and PCIe
interfaces.
This patch adds support for it.
The corresponding DTSI file, from Linux next-20180720, is also
introduced.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
As the Allwinner H6 chip has a new memory map, its GIC MMIO address is
thus different.
Change the address on H6.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
On the new Allwinner H6 SoC, the SRAM A2 address (SPL load address) is
at 0x20000, which is different with any old Allwinner SoCs.
Add SPL position and size configuration for this.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The new Allwinner H6 SoC has its SRAM A1 at neither 0x0 nor 0x10000, but
it's at 0x20000. Thus the SUNXI_HIGH_SRAM option needs to be refactored
to support this new configuration.
Change it to SUNXI_SRAM_ADDRESS, which holds the real address of SRAM
A1 in the memory map.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
AXS10x boards have preloader that reads SPI flash pages and searches
special image header to fetch and load binary.
Add tool, make target (bsp-generate) to generate
update script and u-boot binary image with header for preloader.
Also add script to default environment to apply updates.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ePTT
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-07-25
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
When called with ENVOP_SAVE, env_get_location() only returns the
gd->env_load_location variable without actually checking for
the environment location and priority.
This behaviour causes env_save() to fall into an infinite loop when
the low-level drv->save() call fails.
The env_save() function should not loop through the environment
location list but it should save the environment into the location
stored in gd->env_load_location by the last env_load() call.
Signed-off-by: Nicholas Faustini <nicholas.faustini@azcomtech.com>
Reviewed-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
While there is probably no reason to do so in a real life situation, it
will allow to compile test both stacks with the same sandbox defconfig.
As we cannot define two 'tpm' commands at the same time, the command for
TPM v1 is still called 'tpm' and the one for TPM v2 'tpm2'. While this
is the exact command name that must be written into eg. test files, any
user already using the TPM v2 stack can continue to do so by just writing
'tpm' because as long as TPM v1 support is not compiled, U-Boot prompt
will search for the closest command named after 'tpm'.
The command set can also be changed at runtime (not supported yet, but
ready to be), but as one can compile only either one stack or the other,
there is still one spot in the code where conditionals are used: to
retrieve the v1 or v2 command set.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: In sandbox_tpm2_fill_buf() use NULL not \0 to ensure NULL
terminated string due to LLVM warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
The udevice given to the open() function of course must be opened,
not closed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With some recent changes to relevant drivers here the openrd board
(openrd_client in this case) does not fit within its size constraint.
We can however drop the slightly extended baudrate table and then the
duplication of mtdparts/mtdids in the default environment. These
defaults are set in the environment by the 'mtdparts' command and
otherwise referenced throughout the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
The default value with distro_bootcmd is 2 seconds, which is
reasonably fast, and provides a consistent experience across platforms
supporting distro_bootcmd.
The current bootdelay value of 0 seconds is a bit challenging to
interrupt when desired.
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Enable distro_bootcmd for a standardized boot process across multiple
platforms.
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adding distro_bootcmd support bumps the default environment size over
4500. Increase to SZ_16K to allow for room to grow in the future.
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Replace non-standard variable names kerneladdr, initrdaddr and fdtaddr
with kernel_addr_r, ramdisk_addr_r and fdt_addr_r, as documented in
u-boot README.
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Now the UCLASS_ETH device "node" field is owerwritten by some network drivers in
case of Ethernet PHYs which are linked to UCLASS_ETH device using
"phy-handle" DT property and when Ethernet PHY driver needs to read some
additional information from DT. In such cases following happens (in
general):
- network drivers
priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
priv->interface);
<-- phydev is connected to dev which is UCLASS_ETH device
if (priv->phy_of_handle > 0)
dev_set_of_offset(priv->phydev->dev, priv->phy_of_handle);
<-- phydev->dev->node is overwritten by phy-handle DT node
- PHY driver in .config() callback
int node = dev_of_offset(dev);
<-- PHY driver uses overwritten dev->node
const void *fdt = gd->fdt_blob;
if (fdtdec_get_bool(fdt, node, "property"))
...
As result, UCLASS_ETH device can't be used any more for DT accessing.
This patch adds additional ofnode node field to struct phy_device which can
be set explicitly by network drivers and used by PHY drivers, so
overwriting can be avoided. Also add helper function phy_get_ofnode()
which will check and return phy_device->node or dev_ofnode(phydev->dev) for
backward compatibility with existing drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Because some phy wants to export some functions [1], export.h was
including the whole phy subsystem which pulls in lots of stuff that
causes some ordering and redefinition issues. Split out the only part
that is actually needed in export.h and include it there and in phy.h.
[1] commit 9527931507 ("board/ls2085rdb: Export functions for
standalone AQ FW load apps")
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The same basic parsing was implemented in tftp and nfs, so add a helper
function to do the work once.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
For net_boot_common, we allow the serverip to be specified as part of
the boot file name. For net commands that require serverip, include that
source as a valid specification of serverip.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
A new defconfig is introduced to support SPL boot from QSPI NOR
flash. This is to support falcon mode for faster booting into
Linux.
Signed-off-by: York Sun <york.sun@nxp.com>
For SoCs with PBL, u-boot-with-spl-pbl.bin is the final image for
SPL boot. Drop unused u-boot-with-spl.bin.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Ashish Kumar <ashish.kumar@nxp.com>
CC: Ruchika Gupta <ruchika.gupta@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
For SPL boot with PBL, u-boot-with-spl-pbl.bin is the final image.
Drop unused u-boot-with-spl.bin.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Ruchika Gupta <ruchika.gupta@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
CC: Udit Agarwal <udit.agarwal@nxp.com>
CC: Sumit Garg <sumit.garg@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Commit a52ff334c5 ("armv8: ls1046ardb: SPL size reduction") reduced
image size for SPL. IFC was disabled. If PPA is loaded in SPL, MMU is
enabled as a result. Removing IFC skips IFC region in the MMU table,
causing later failure in RAM version U-boot when accessing CPLD
through IFC. Only disable IFC if PPA is not enabled for SPL.
Signed-off-by: York Sun <york.sun@nxp.com>
Move CONFIG_SPI_FLASH_SPANSION, CONFIG_SPI_FLASH, to defconfig.
Also disable disable 4K erase size option.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
use "fsl_mc lazyapply dpl addr" instead of "fsl_mc apply dpl addr"
change dpl load addr to 0x80001000 from 0x80200000 because dpl gets
corrupted at 0x80200000 during bootm command excecution.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove unused function efi_get_time_init().
Initialization of the RTC has to be done in board bring up not in the EFI
subsystem.
There is no RTC device in the UEFI spec. The RTC is only accessed through
the runtime services.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use const for the buffer. We are not changing the buffer.
Use efi_uintn_t where prescribed by the UEFI spec.
Prefer u32 over uint32_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The system table contains a link to the list of configurations tables.
These include the device tree, SMBIOS table, and the ACPI table.
This array is currently statically linked. With the patch it is allocated
as EFI_RUNTIME_SERVICES_DATA. Due to the structure of the system table we
cannot work with a linked list here.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
