The 8572 DDR erratum1:
DDR controller may enter an illegal state when operating
in 32-bit bus mode with 4-beat bursts.
Description:
When operating with a 32-bit bus, it is recommended that
DDR_SDRAM_CFG[8_BE] is cleared when DDR2 memories are used.
This forces the DDR controller to use 4-beat bursts when
communicating to the DRAMs. However, an issue exists that
could lead to data corruption when the DDR controller is
in 32-bit bus mode while using 4-beat bursts.
Projected Impact:
If the DDR controller is operating in 32-bit bus mode with
4-beat bursts, then the controller may enter into a bad state.
All subsequent reads from memory is corrupted.
Four-beat bursts with a 32-bit bus only is used with DDR2 memories.
Therefore, this erratum does not affect DDR3 mode.
Work Arounds:
To work around this issue, software must set DEBUG_1[31] in
DDR memory mapped space (CCSRBAR offset + 0x2f00 for DDR_1
and CCSRBAR offset + 0x6f00 for DDR_2).
Currenlty, the code is using incorrect register DDR_SDRAM_CFG_2
as condition, but it should be DDR_SDRAM_CFG register.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Introduce CONFIG_E500MC to deal with the minor differences between
e500v2 and e500mc.
* Certain fields of HID0/1 don't exist anymore on e500mc
* Cache line size is 64-bytes on e500mc
* reset value of PIR is different
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Using CONFIG_SYS_CACHELINE_SIZE instead of 31 means we can handle
e500mc's 64-byte cacheline properly when it gets added.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As "ppc44x: Unification of virtex5 pp440 boards" did for the xilinx
ppc440 boards, this patch presents a common architecture for all the
xilinx ppc405 boards.
Any custom xilinx ppc405 board can be added very easily with no code
duplicity.
This patch also adds a simple generic board, that can be used on almost
any design with xilinx ppc405 replacing the file ppc405-generic/xparameters.h
This patch is prepared to work with the latest version of EDK (10.1)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
Some Blackfin UARTs are read-to-clear while others are write-to-clear.
This can cause problems when we poll the LSR and then later try and handle
any errors detected.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Use the sti instruction to set the initial interrupt mask rather than
banging on the core IMASK MMR to save both space and time.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We should use the algorithm in the Linux kernel so that the UART divisor
calculation is more accurate. It also fixes problems on some picky UARTs
that have sampling anomalies.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
During cpu init, make sure we initialize the CEC properly so that
interrupts can fire and be handled while U-Boot is running.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is done to allow other 83XX based platforms which also have UPM
(e.g. 8360) to configure and use their UPM in u-boot.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The rfcks should be shifted by 28 bits left. We didn't notice the bug
because we were using only 100MHz clocks (for which rfcks == 0).
Though, for SGMII we'll need 125MHz clocks.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Previously only the NOR flash mapping was written into the ranges
property of the ebc node. This patch now writes all enabled chip
select areas into the ranges property.
Signed-off-by: Stefan Roese <sr@denx.de>
Provide a weak defined routine to retrieve the CPU number for
reference boards that have multiple CPU's. Default behavior
is the existing single CPU print output. Reference boards with
multiple CPU's need to provide a board specific routine.
See board/amcc/arches/arches.c for an example.
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch add the capability to configure a PPC440 based IBM SDRAM
Controller with static, compiled-in, values. PPC440 memory subsystem
includes a Memory Queue core.
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Some cores don't support ethernet stashing at all, and some
instances have errata. Adds 3 properties to gianfar nodes
which support stashing. For now, just add this support to
85xx SoCs.
Signed-off-by: Andy Fleming <afleming@freescale.com>
* Check DDR interleaving mode from environment by reading memctl_intlv_ctl and
ba_intlv_ctl.
* Print DDR interleaving mode information
* Add doc/README.fsl-ddr to describe the interleaving setting
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Because some dimm parameters like n_ranks needs to be used with the board
frequency to choose the board parameters like clk_adjust etc. in the
board_specific_paramesters table of the board ddr file, we need to pass
the dimm parameters to the board file.
* move ddr dimm parameters header file from /cpu to /include directory.
* add ddr dimm parameters to populate board specific options.
* Fix fsl_ddr_board_options() for all the 8xxx boards which call this function.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Fix some bugs:
1. Correctly set intlv_ctl in cs_config.
2. Correctly set sa, ea in cs_bnds when bank interleaving mode is enabled.
3. Set base_address and total memory for each ddr controller in memory
controller interleaving mode.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Added the ability for C code to invalidate the i/d-cache's and
to flush the d-cache. This allows us to more efficient change mappings
from cache-able to cache-inhibited.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.
Signed-off-by: Heiko Schocher <hs@denx.de>
Added as a convenience for other platforms that uses MPC8360 (has 8 UCC).
Six eth interface is chosen because the platform I am using combines
UCC1&2 and UCC3&4 as 1000 Eth and the other four UCCs as 10/100 Eth.
Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
At least some revisions of the 8313, and possibly other chips, do not
wait for all pages of the initial 4K NAND region to be loaded before
beginning execution; thus, we wait for it before branching out of the
first NAND page.
This fixes warm reset problems when booting from NAND on 8313erdb.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Set the MQ Read Passing & MCIF Cycle limits to the recommended by AMCC
values. This fixes the occasional 440SPe hard locking issues when the 440SPe's
dedicated DMA engines are used (e.g. by the h/w accelerated RAID driver).
Previously the appropriate initialization had been made in Linux, by the
ppc440spe ADMA driver, which is wrong because modifying the MQ configuration
registers after normal operation has begun is not supported and could
have unpredictable results.
Comment from Stefan: This patch doesn't change the resulting value of the
MQ registers. It explicitly sets/clears all bits to the desired state which
better documents the resulting register value instead of relying on pre-set
default values.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This reverts commit dffd2446fb.
The fix introduced by this patch is not correct. The problem is
that the documentation is not correct for the MPC8544 with regards
to which bit in PORDEVSR2 is for the SEC_CFG.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Reference manual states that MxMR[MAD] increment is the indication
of write to UPM array is complete. Honour that. Also, make the dummy
write explicit.
also fix the comment.
Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
At a lot of places in the code the PIPE_INTERRUPT flags and friends
are used wrong. The wrong bits are compared to this flag resulting
in wrong conditions. Also there are macros that should be used for
PIPE_* flags.
This patch tries to fix them all, however, I was not able to test the
changes, because I do not have any of these boards.
Review required!
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
This is needed in unlock_ram_in_cache() because it is called from C and
will corrupt the small data area anchor that is kept in R2.
lock_ram_in_cache() is modified similarly as good coding practice, but
is not called from C.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
For some reason we duplicated the majority of code in lib_ppc/interrupts.c
Not know how that happened, but there is no good reason for it.
Use the interrupt_init_cpu() and timer_interrupt_cpu() since its why
they exist.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Measurements with our MPC8544 board showed that the I2C bus frequency
is wrong by a factor of 1.5. Obviously, the interpretation of the
MPC85xx_PORDEVSR2_SEC_CFG bit of the cfg_sec_freq register is not
correct. There seems to be an error in the 8544 RM.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Switch to the standard CFG_HZ=1000 value, while at it, minor white-space
cleanup, remove CFG_CLKS_IN_HZ from config-headers. Tested on mx31ads,
provides 2% or 0.4% precision depending on the
CONFIG_MX31_TIMER_HIGH_PRECISION flag. Measured with stop-watch on 100s
boot-delay.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
After changing SDRAM_CLKTR phase value rerun the memory preload
initialization sequence (INITPLR) to reset and relock the memory
DLL. Changing the SDRAM_CLKTR memory clock phase coarse timing
adjustment effects the phase relationship of the internal, to the
PPC chip, and external, to the PPC chip, versions of MEMCLK_OUT.
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
On 8536DS board, When the DDR clk is set async mode(SW3[6:8] != 111),
The display is still sync mode DDR freq. This patch try to fix
this. The display DDR freq is now the actual freq in both
sync and async mode.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
ePAPR says if the *cache-block-size is the same as *cache-line-size
than we don't need the *cache-line-size property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The spd_dram code shifts the base address, then masks 20 bits, but
forgets to shift the base address back. Fix this by just masking the
base address correctly.
Found this bug while trying to relocate a DDR memory at the base != 0.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
eventually leads to a machine check. This change assures that DPRAM
is allocated only once in that case.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch fixes a problem introdiced with patch
bbeff30c [ppc4xx: Remove superfluous dram_init() call or replace it by
initdram()].
The boards affected are:
- PCI405
- PPChameleonEVB
- quad100hd
- taihu
- zeus
Signed-off-by: Stefan Roese <sr@denx.de>
This patch prevents linker error on AT91RM9200 boards, if
CONFIG_CMD_I2_TREE is set.
It implements i2c_set_bus_speed and i2c_get_bus_speed as a dummy function.
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
This patch changes get_timer() for i.MX to return the time since
'base' instead of the time since the counter was at zero.
Symptom seen is flash timeout errors when erasing or programming a
sector using the common cfi flash code.
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
1) Change the i.MX serial driver to use the baud rate set in the
u-boot environment
2) don't assume a 16MHz value for PERCLK1 in baud rate calculations
3) don't write a 1 to the RDR bit in the USR2 reg. (bit is not "write
one to clear" like other status bits in the reg.)
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
Code in cpu/arm920t/start.S will die with a compilation error if
CONFIG_STACKSIZE + CFG_MALLOC_LEN works out to an invalid constant for
the ARM sub instruction. Change the code so that each is subtracted
independently to avoid the error.
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
This patch adds the reset_timer() function (needed by nand_base.c) and
modifies the get_timer_masked() to work in the same way as the omap24xx
function.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Based on original patch by Bernard Blackham <bernard@largestprime.net>
U-boot's HW ECC support for large page NAND on Davinci is completely
broken. Some kernels, such as the 2.6.10 one supported by
MontaVista for DaVinci, rely upon this broken behaviour as they
share the same code for ECCs. In the existing scheme, error
detection *might* work on large page, but error correction
definitely does not. Small page ECC correction works, but the
format is not compatible with the mainline git kernel.
This patch adds ECC code that matches what is currently in the
Davinci git repository (since NAND support was added in 2.6.24).
This makes the ECC and OOB layout written by u-boot compatible with
Linux for both small page and large page devices and fixes ECC
correction for large page devices.
The old behaviour can be restored by defining the macro
CFG_DAVINCI_BROKEN_ECC, which is undefined by default.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Acked-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Fix printf format-string/arg mismatches under -DDEBUG.
These warnings occur with DEBUG defined for a platform using
cpu/mpc85xx. Users of other architectures can unearth similar
problems by adding the line "CFLAGS += -DDEBUG=1" in config.mk right
after "CFLAGS += $(call cc-option,-fno-stack-protector)".
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The e500um says the timebase is volatile out of reset. To ensure
TB sync works we need to make sure its zero.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes warnings like this:
start.S:0: warning: target CPU does not support interworking
which come from some ARM cross compilers and are caused by hard-coded
(with "--with-cpu=arm9" configuration option) ARM targets (which
support ARM Thumb instructions), while the ARM target selected from
the command line (with "-march=armv4") doesn't support Thumb
instructions.
This warning is issued by the compiler regardless of the real use of
the Thumb instructions in code.
To fix this problem, we use options according to compiler version
being used.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Since this define is only used on one board that was never really in
production, removing this compile time option doesn't hurt and makes
the code more readable.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a compilation warning for the PIP405 board. It moves the
#ifndef CONFIG_CS8952_PHY define a little so that the warning doesn't
occur anymore. I am a little unsure if this #ifdef is at the correct
place now or if it could be removed completely. This needs to get
tested on the PIP405 board.
Signed-off-by: Stefan Roese <sr@denx.de>
ctrl_regs.c: In function 'compute_fsl_memctl_config_regs':
ctrl_regs.c:523: warning: 'caslat' may be used uninitialized in this function
ctrl_regs.c:523: note: 'caslat' was declared here
Add a warning in DDR1 case if cas_latency isn't a value we know about.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds GPCS, SGMII and M88E1112 PHY support
for the AMCC PPC460GT/EX processors.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Alternate SDRAM DDR autocalibration routine that can be generically used
for any PPC4xx chips that have the IBM SDRAM Controller core allowing for
support of more DIMM/memory chip vendors and gets the DDR autocalibration
values which give the best read latency performance (SDRAM0_RDCC.[RDSS]).
Two alternate SDRAM DDR autocalibration algoritm are provided in this patch,
"Method_A" and "Method_B". DDR autocalibration Method_A scans the full range
of possible PPC4xx SDRAM Controller DDR autocalibration values and takes a
lot longer to run than Method_B. Method_B executes in the same amount of time
as the currently existing DDR autocalibration routine, i.e. 1 second or so.
Normally Method_B is used and it is set as the default method.
The current U-Boot PPC4xx DDR autocalibration code calibrates the IBM SDRAM
Controller registers.[bit-field]:
1) SDRAM0_RQDC.[RQFD]
2) SDRAM0_RFDC.[RFFD]
This alternate PPC4xx DDR autocalibration code calibrates the following
IBM SDRAM Controller registers.[bit-field]:
1) SDRAM0_WRDTR.[WDTR]
2) SDRAM0_CLKTR.[CKTR]
3) SDRAM0_RQDC.[RQFD]
4) SDRAM0_RFDC.[RFFD]
and will also use the calibrated settings of the above four registers that
produce the best "Read Sample Cycle Select" value in the SDRAM0_RDCC.[RDSS]
register.[bit-field].
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cleans up some latent issues with the data cache control so that
dcache_enable() and dcache_disable() will work reliably (after
unlock_ram_in_cache() has been called)
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Record the Arbiter Event Register values and optionally display them.
The Arbiter Event Register can record the type and effective address of
an arbiter error, even through an HRESET. This patch stores the values in
the global data structure.
Display of the Arbiter Event registers immediately after the RSR value
can be enabled with defines. The Arbiter values will only be displayed
if an arbiter event has occured since the last Power On Reset, and either
of the following defines exist:
#define CONFIG_DISPLAY_AER_BRIEF - display only the arbiter address and
and type register values
#define CONFIG_DISPLAY_AER_FULL - display and interpret the arbiter
event register values
Address Only transactions are one of the trapped events that can register
as an arbiter event. They occur with some cache manipulation instructions
if the HID0_ABE (Address Broadcast Enable) is set and the memory region
has the MEMORY_COHERENCE WIMG bit set. Setting:
#define CONFIG_MASK_AER_AO - prevents the arbiter from recording address
only events, so that it can still capture
other real problems.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This is needed in unlock_ram_in_cache() because it is called from C and
will corrupt the small data area anchor that is kept in R2.
lock_ram_in_cache() is modified similarly as good coding practice, but
is not called from C.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Set DAT value before DIR values to avoid creating glitches on the
GPIO signals.
Set gpio level register before direction register to inhibit
glitches on high level output pins.
Dir and data gets cleared at powerup, so high level output lines see
a short low pulse between setting the direction and level registers.
Issue was seen on a new board with the nReset line of the NOR flash
connected to a GPIO. Setting the direction register puts the NOR flash
in reset so the next instruction to set the level cannot get executed.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Modified board_eth_init() functions of boards that have this FEC in addition
to other Ethernet controllers.
Affected boards:
bc3450
icecube
mvbc_p
o2dnt
pm520
total5200
tq5200
Removed initialization of controller from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The tsec driver contains a hard-coded array of configuration information
for the tsec ethernet controllers. We create a default function that works
for most tsecs, and allow that to be overridden by board code. It creates
an array of tsec_info structures, which are then parsed by the corresponding
driver instance to determine configuration. Also, add regs, miiregs, and
devname fields to the tsec_info structure, so that we don't need the kludgy
"index" parameter.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Notice: USB on S3C6400 currently works _only_ with switched off MMU. One could
try to enable the MMU, but map addresses 1-to-1, and disable data cache, then
it should work too and we could still profit from instruction cache.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
DM644x is just one of a series of DaVinci chips that use the EMAC driver.
By replacing all the function names that start with dm644x_* to davinci_*
we make these function more portable. I have tested this change on my EVM.
DM6467 is another DaVinci SOC which uses the EMAC driver and i will
be sending patches that add DaVinci DM6467 support to the list soon.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This function is needed for the new NAND infrastructure. We only need
a dummy implementation though for the NDFC.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a UIC external_interrupt hang if critical or non-critical
interrupt is set at the same time as a normal interrupt is set on UIC0.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Removed Magic numbers from Initialization preload registers
Tested with Kilauea, Glacier, Canyonlands and Katmai boards
About 5-7% improvement seen for LMBench memtests
Signed-off-by: Prodyut Hazarika <phazarika@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
For some reason we duplicated the majority of code in lib_ppc/interrupts.c
not show how that happened, but there is no good reason for it.
Use the interrupt_init_cpu() and timer_interrupt_cpu() since its why
they exist.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8536 Adds SDHC and SATA controllers to the PQ3 family. We
also have SERDES init code for the 8536.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Compute DIMM parameters based upon the SPD information.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Compute DIMM parameters based upon the SPD information in spd.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The main purpose of this rewrite it to be able to share the same
initialization code on all FSL PowerPC products that have DDR
controllers. (83xx, 85xx, 86xx).
The code is broken up into the following steps:
GET_SPD
COMPUTE_DIMM_PARMS
COMPUTE_COMMON_PARMS
GATHER_OPTS
ASSIGN_ADDRESSES
COMPUTE_REGS
PROGRAM_REGS
This allows us to share more code an easily allow for board specific code
overrides.
Additionally this code base adds support for >4G of DDR and provides a
foundation for supporting interleaving on processors with more than one
controller.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds a helper function to unlock the PCI configuration bit, so that
any extra PCI setup (such as outbound windows, etc.) can be done after
using the 83XX_GENERIC_PCI code to set up the PCI bus.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- According to ARM Dual-Timer Module (SP804) TRM (ARM DDI0271),
-- Timer Value Register @ TIMER Base + 4 is Read-only.
-- Prescale Value (Bits 3-2 of TIMER Control register)
can only be one of 00,01,10. 11 is undefined.
-- CFG_HZ for Versatile board is set to
#define CFG_HZ (1000000 / 256)
So Prescale bits is set to indicate
- 8 Stages of Prescale, Clock divided by 256
- The Timer Control Register has one Undefined/Shouldn't Use Bit
So we should do read/modify/write Operation
Signed-off-by: Gururaja Hebbar <gururajakr@sanyo.co.in>
During recent PCI-E tests it has been found that current
driverl level and de-emphasis values are not set correctly.
After sweeping throgh all de-ephasis values, it was found that
0x130 is a right value. Where 0x13 is driver level and 0 is
de-emphasis.
Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes some minor issues introduced with the patch:
ppc4xx: Optimize PLB4 Arbiter... from Prodyut Hazarika:
- Rework memory-queue and PLB arbiter optimization code, that the
local variable is not needed anymore. This removes one #ifdef.
- Use consistant spacing in ppc4xx.h header (XXX + 0x01 instead
of XXX+ 0x01). This was not introduced by Prodyut, just a
copy-paste problem.
Signed-off-by: Stefan Roese <sr@denx.de>
PPC405EX and PPC460EX/GT/SX
- Read pipeline depth set to 4 for PPC440SP/SPE, PPC405EX, PPC460EX/GT/SX
processors
- Moved PLB4 Arbiter register definitions to ppc4xx.h since it is shared
across processors (405 and 440/460)
- Optimize Memory Queue settings for PPC440SP/SPE and PPC460EX/GT/SX
processors
- Add register bit definitions for Memory Queue Configuration registers
Signed-off-by: Prodyut Hazarika <phazarika@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Move to using the environment variables 'ethaddr', 'eth1addr', etc..
instead of bd->bi_enetaddr, bi_enet1addr, etc.
This makes the code a bit more flexible to the number of ethernet
interfaces.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is no point in disabling the icache on 7xx/74xx/86xx parts and not
also flushing the icache. All callers of invalidate_l1_instruction_cache()
call icache_disable() right after. Make it so icache_disable() calls
invalidate_l1_instruction_cache() for us.
Also, dcache_disable() already calls dcache_flush() so there is no point
in the explicit calls of dcache_flush().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Incorrect CFG_HZ value, change 1000000 to 1000.
Rename #waring to #warning. RAMBAR1 uses twice
in start.S, rename the later to FLASHBAR. Insert
nop for DRAM setup. And, env_offset in linker file.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Note that with older board revisions, NAND boot may only work after a
power-on reset, and not after a warm reset. I don't have a newer board
to test on; if you have a board with a 33MHz crystal, please let me know
if it works after a warm reset.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Here comes a trivial patch to cpu/arm926ejs/davinci/nand.c. Unfortunately I
don't have hardware handy so I can not test it at the moment but changes are
rather trivial so it should work. It would be nice if somebody with a
hardware checked it anyways.
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
This patch changes the 4xx NAND driver ndfc.c to match the new
infrastructure from the updated NAND subsystem. This NAND
subsystem was recently synced again with the Linux 2.6.22 MTD/NAND
subsystem.
Tested successfully on AMCC Sequoia and Bamboo.
Signed-off-by: Stefan Roese <sr@denx.de>
- Fixing leading white spaces
- Fixing indentation where 4 spaces are used instead of tab
- Removing C++ comments (//), wherever I introduced them
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.
This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.
MAKEALL ppc/arm has some issues:
* DOC/OneNand/nand_spl is not building (I have not tried porting
these parts, and since I do not have any HW and I am not familiar
with this code/HW I think its best left to someone else.)
Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
cpu/ppc4xx/ndfc.c
cpu/arm926ejs/davinci/nand.c
board/delta/nand.c
board/zylonite/nand.c
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use CONFIG_NUM_CPUS to match existing define used by 86xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
This is needed because we will be possibly be locating
devices at physical addresses above 32bits, and the asm
preprocessing does not appear to deal with ULL constants
properly. We now call write_bat in lib_ppc/bat_rw.c.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Correct the mx31_gpio_mux() function to allow changing all i.MX31 IOMUX
contacts instead of only the first 256 ones as is the case prior to
this patch.
Add missing MUX_* macros and update board files to use the new macros.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
On ADS5121 when booting linux the following errors are seen:
Unable to update property /soc5121@80000000:bus-frequency, err=FDT_ERR_NOTFOUND
Unable to update property /soc5121@80000000/ethernet@2800:local-mac-address, err=FDT_ERR_NOTFOUND
Unable to update property /soc5121@80000000/ethernet@2800:address, err=FDT_ERR_NOTFOUND
This is caused by ft_cpu_setup trying to deal with
both old and new soc node naming. This patch
fixes this by being smarter about what to
fixup.
Also do soc node fixups by compatible instead of by path.
A new board config called OF_SOC_COMPAT defined
to be "fsl,mpc5121-immr" replaces the old
OF_SOC node path that was defined to be "soc@80000000".
Old device trees still work, but the compatiblity
is conditional on CONFIG_OF_SUPPORT_OLD_DEVICE_TREES
which is on by default in include/configs/ads5121.h.
Signed-off-by: John Rigby <jrigby@freescale.com>
The Hammerhead platform is built around a AVR32 32-bit microcontroller
from Atmel. It offers versatile peripherals, such as ethernet, usb
device, usb host etc.
The board also incooperates a power supply and is a Power over Ethernet
(PoE) Powered Device (PD).
Additonally, a Cyclone III FPGA from Altera is integrated on the board.
The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two
DDR2 SDRAM interfaces, which will cover even the most exceptional need
of memory bandwidth. Together with the onboard video decoder the board
is ready for video processing.
For more information see: http:///www.miromico.com/hammerhead
Signed-off-by: Julien May <mailinglist@miromico.ch>
[haavard.skinnemoen@atmel.com: various small fixes and adaptions]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Support for the adsvix was originally provided by Applied Data
Systems (ADS), inc., now EuroTech, Inc.
The board never shipped aside from some sample boards.
Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
Use CFG_MIPS_TIMER_FREQ when computing the baudrate divisor
on alchemy cpus.
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
This patch fixes a problem with incorrect MODTx (On Die Termination)
setup for a configuration with multiple DIMM's and multiple ranks.
Without this change Katmai was unable to boot Linux with DDR2 frequency
>= 533MHz and mem>=3GB. With this patch Katmai successfully boots Linux
with DDR2 frequency = 640MHz and mem=4GB.
Signed-off-by: Stefan Roese <sr@denx.de>
-This patchs gives support for the embbedded ppc440
on the Virtex5 FPGAs
-interrupts.c divided in uic.c and interrupts.c
-xilinx_irq.c for xilinx interrupt controller
-Include modifications propossed by Stefan Roese
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Acked-by: Stefan Roese <sr@denx.de>
The L2 size detection code was a bit confusing and we kept having to add
code to it to handle new processors. Change the sense of detection so we
look for the older processors that aren't changing.
Also added support for 1M cache size on 8572.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some boards that have external 16550 UARTs don't have a direct
tie between bi_busfreq and the clock used for the UARTs. Boards
that do have such a tie should set CFG_NS16550_CLK to be
get_bus_freq(0) -- which most of them do already.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
With a page size of BOOKE_PAGESZ_16M, both the real and effective
addresses must be multiples of 16MB. The hardware silently truncates
them so the code happens to work. This patch clarifies the situation
by establishing addresses that the hardware doesn't need to truncate.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Delete the crypto node if not on an E-processor. If on 8360 or 834x family,
check rev and up-rev crypto node (to SEC rev. 2.4 property values)
if on an 'EA' processor, e.g. MPC8349EA.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch removes some ft_board_setup() functions from some 4xx boards.
This can be done since we now have a default weak implementation for this
in cpu/ppc4xx/fdt.c. Only board in need for a different/custom
implementation like canyonlands need their own version.
Signed-off-by: Stefan Roese <sr@denx.de>
Remove all CFG_CSn_RO in cpu/mcf52x2/cpu_init.c. If
CFG_CSn_RO is defined as 0, the chipselect will not
be assigned.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Rename CONFIG_MCFTMR to CONFIG_MCFRTC to include real time
clock module in cpu/<cf arch>/cpu_init.c
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
This patch now moves common.h to the top of the inlcude list. This
is needed for boards with CONFIG_PHYS_64BIT set (e.g. katmai), so that
the phys_size_t/phys_addr_t are defined to the correct size in this
driver.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch reworks the 440GX interrupt handling so that the common 4xx
code can be used. The 440GX is an exception to all other 4xx variants
by having the cascading interrupt vectors not on UIC0 but on a special
UIC named UICB0 (UIC Base 0). With this patch now, U-Boot references
the 440GX UICB0 when UIC0 is selected. And the common 4xx interrupt
handling is simpler without any 440GX special cases.
Also some additional cleanup to cpu/ppc4xx/interrupt.c is done.
Signed-off-by: Stefan Roese <sr@denx.de>
This 2nd patch now removes all UIC mask bit definition. They should be
generated from the vectors by using the UIC_MASK() macro from now on.
This way only the vectors need to get defined for new PPC's.
Also only the really used interrupt vectors are now defined. This makes
definitions for new PPC versions easier and less error prone.
Another part of this patch is that the 4xx emac driver got a little
cleanup, since now the usage of the interrupts is clearer.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is the first step to consolidate the UIC related defines in the
4xx headers. Move header from asm-ppc/ppc4xx-intvec.h to
asm-ppc/ppc4xx-uic.h as it will hold all UIC related defines in the next
steps.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes some ft_board_setup() functions from some 4xx boards.
This can be done since we now have a default weak implementation for this
in cpu/ppc4xx/fdt.c. Only board in need for a different/custom
implementation like canyonlands need their own version.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for placing the RGMII bridge on the
PPC405EX(r) into MII/GMII mode and allows a board-specific
configuration to specify the bridge mode at compile-time.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch completes the preprocessor mneomics for the IBM DDR2 SDRAM
controller registers (MODT and INITPLR) used by the
PowerPC405EX(r). The MMODE and MEMODE registers are unified with their
peer values used for the INITPLR MR and EMR registers,
respectively. Finally, a spelling typo is correct (MANUEL to MANUAL).
With these mnemonics in place, the CFG_SDRAM0_* magic numbers for
Kilauea are replaced by equivalent mnemonics to make it easier to
compare and contrast other 405EX(r)-based boards (e.g. during board
bring-up).
Finally, unified the SDRAM controller register dump routine such that
it can be used across all processor variants that utilize the IBM DDR2
SDRAM controller core. It produces output of the form:
PPC4xx IBM DDR2 Register Dump:
...
SDRAM_MB0CF[40] = 0x00006701
...
which is '<mnemonic>[<DCR #>] = <value>'. The DCR number is included
since it is not uncommon that the DCR values in header files get mixed
up and it helps to validate, at a glance, they match what is printed
in the user manual.
Tested on:
AMCC Kilauea/Haleakala:
- NFS Linux Boot: PASSED
- NAND Linux Boot: PASSED
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Stefan Roese <sr@denx.de>
ADS5121 Rev 3 board is now the default config
config targets are now
ads5121_config
Rev 3 board with
PCI
M41T62 on board RTC
512MB DRAM
ads5121_rev2_config
Rev 2 board with
No PCI
256MB DRAM
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: John Rigby <jrigby@freescale.com>
This patch fixes ppc4xx related printf format warning. Those warnings are
now visible since patch dc4b0b38d4
[Fix printf errors.] by Andrew Klossner has been applied. Thanks, this is
really helpful.
Signed-off-by: Stefan Roese <sr@denx.de>
Newer PPC's like 440SPe, 460EX/GT can be equipped with more than 2GB of SDRAM.
To support such configurations, we "only" map the first 2GB via the TLB's. We
need some free virtual address space for the remaining peripherals like, SoC
devices, FLASH etc.
Note that ECC is currently not supported on configurations with more than 2GB
SDRAM. This is because we only map the first 2GB on such systems, and therefore
the ECC parity byte of the remaining area can't be written.
Signed-off-by: Stefan Roese <sr@denx.de>
This is particularly problematic now that non-NAND-specific code is
including <nand.h>, and thus all debugging code is being compiled
regardless of whether it was requested, as reported by Scott McNutt
<smcnutt@psyent.com>.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This makes it easier to use the driver on other platforms.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
After we move the atmel_mci driver into drivers/mmc, we can't select
it with CONFIG_MMC anymore. Introduce a new symbol specifically for
this driver so that there's no ambiguity.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The compiler will help find mismatches between printf formats and
arguments if you let it. This patch adds the necessary attributes to
declarations in include/common.h, then begins to correct the resulting
compiler warnings. Some of these were bugs, e.g., "$d" instead of
"%d" and incorrect arguments. Others were just annoying, like
int-long mismatches on a system where both are 32 bits. It's worth
fixing the annoying errors to catch the real ones.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
By Cleanup out-or-tree building for some boards (.depend)
(commit:c8a3b109f07f02342d097b30908965f7261d9f15)
because filse ware changed, some SH-boards have compile error.
I revised this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The watchdog on 8610 board is enabled by setting sw[6]
to on. Once enabled, the watchdog can not be disabled
by software. So feed the dog in u-boot is necessary for
normal operation.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Remove duplicate code in cpu/arm926ejs/davinci/lxt972.c.
Remove duplicate code in a if/else block in
cpu/arm926ejs/davinci/lxt972.c.
Fixed style issues.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Remove duplicate definitions in include/lxt971a.h.
Remove duplicate registers and bits definitions in
include/lxt971a.h for standard MII registers, and
use values in include/miiphy.h instead.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This change helps with better handling with others
Xilinx based platform.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stefan Roese <sr@denx.de>
This patch is the first step in cleaning up net/eth.c, by moving Ethernet
initialization to CPU or board-specific code. Initial implementation is
only on the Freescale TSEC controller, but others will be added soon.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Conflicts:
board/amirix/ap1000/serial.c
board/exbitgen/exbitgen.c
board/exbitgen/flash.c
board/ml2/serial.c
board/xilinx/ml300/serial.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
The Register URXD contains status information in bits [15..8].
With status bit 15 set, CTRL-C was reported as 0x8003 instead
of 0x03. Therefore CTRL-C was not detected.
To solve this, bits [15..8] were masked out now.
Signed-off-by: Juergen Kilb <J.Kilb@gmx.de>
Acked-by: Felix Radensky <felix@embedded-sol.com>
This patch fixes a bug where the 460EX/GT PCIe UTLSET1 register was
configured incorrectly. Thanks to Olga Buchonina from AMCC for pointing
this out.
Signed-off-by: Stefan Roese <sr@denx.de>
