Add new sysinfo IDs for R-Car V3H Condor/Condor-I .
Enable support for sysinfo on R-Car V3H Condor/Condor-I. The sysinfo is
used e.g. to access and decode board-specific information and then in
turn used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77980.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Update the commit message, note the new sysinfo IDs.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
Correct the board code ID based on the hardware documentation
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Remove PFC info table entries which are never instantiated,
since there are no drivers for those. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The CLK_RCAR_GEN3 registers two subdrivers, clk_gen3 and rst_gen3.
The former depends on the clock framework, which is always enabled
in this context of clock framework driver, while the later depends
on reset framework which may not always be enabled.
Ensure the reset framework is also always enabled to prevent inobvious
early boot time bind failure of the CPG driver, which leads to system
showing no activity and is difficult to debug.
Note that one possible approach to debug this is to use CONFIG_DEBUG_UART
and add debug printascii()s into the drivers/clk/renesas/clk-rcar-gen3.c .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In case one of the calls in probe fail, trigger a fail path and
undo all the steps done in probe until the point of failure.
The current implementation failed to stop controller clock and
free claimed clock, so fix that. Furthermore, print return code
in error prints for easier debugging.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The prior stage bootloader might have left the SDnCKCR register in completely
arbitrary state before passing control to U-Boot, which includes the register
being populated with incorrect values. Currently the SDHI driver will attempt
to use clock framework to configure SDn clock, which may fail in case SDnCKCR
contains invalid values for the SDnH clock, because the clock framework would
not be able to determine SDnH clock rate and would get -EINVAL instead, which
in turn would not allow the clock framework to determine the correct SDn clock
divider ratio.
This failure occurs specifically in case SDnCKCR reads back 0x209 .
Correct the problem by first setting default SDnH clock rate to 800 MHz, thus
assuring the SDnCKCR SDnH bits are correct, and only afterward set up the SDn
clock rate to default 200 MHz.
Note that the SDHI driver may reconfigure SDnH clock later based on IOS
settings obtained from the attached card, the 800 MHz set up here is only
the default value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This configuration setting is only relevant if the board supports USB.
It should not be in the main menu but in the USB menu.
The setting is only relevant in USB host mode.
Fixes: 5454dea313 ("usb: hub: allow to increase HUB_DEBOUNCE_TIMEOUT")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Ofnode value is not set, so all the DT properties are not being read
and due to this default values are being used.
Find nand node and set chip->flash_node value.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Bad block table option is hardcoded to read from flash with
NAND_BBT_USE_FLASH option. This decision should be done based on DT
property. Remove this hardcoding, to be able to use DT property.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
It was incorrectly using an old priv->regs pointer, which was
initialized to zero. SPI resets won't happen on first call.
Signed-off-by: Jiajie Chen <c@jia.je>
Link: https://lore.kernel.org/r/20230227150938.211820-1-c@jia.je
Signed-off-by: Michal Simek <michal.simek@amd.com>
When using the fpga loads command, the driver is passing the AES encryption
key address is all cases. However, for the authenticated, but not encrypted
use case, there is no AES encryption key, and this value is 0.
When AES encryption is not used on the fpga bitstream, the pmufw assumes that
the AES key address is a bitstream size value like what is used by the
unsecure fpga load command.
To fix the problem, this patch checks to see if the AES key address is zero.
If the AES key address is zero, it means that AES is not being used on the
bitstream and the bitstream size should be passed instead. Thus, matching
the fpga load functionality.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230214131959.40298-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
There are missing Kconfig dependencies in the code which is using
firmware interface.
The commit 71efd45a5f ("arm64: zynqmp: Change firmware dependency")
add option to also disable ZYNQMP_FIRMWARE. But not all Kconfig
dependencies were properly described and also sdhci and gem drivers
didn't protect the code properly.
So, add the missing ZYNQMP_FIRMWARE dependencies.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230201095553.11219-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- support for fonts wider than 1 byte
- use named header for 8x16 font data
- support multiple fonts configuration
- move get_font_size() to truetype driver ops
- support font size configuration at runtime
- add 16x32 Terminus font from linux
- add 12x22 Sun font from linux
- add 12x22 console simple font test
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZAdiLw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXDtGAJ9ZjsnfneJpUjwYJWOw2ibnm9Dh2QCfVCAy+Bxa
YfqV8y7TbOuCQKTEY1s=
=FJhw
-----END PGP SIGNATURE-----
Merge tag 'next-20230307' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- video console refactoring and optimization
- support for fonts wider than 1 byte
- use named header for 8x16 font data
- support multiple fonts configuration
- move get_font_size() to truetype driver ops
- support font size configuration at runtime
- add 16x32 Terminus font from linux
- add 12x22 Sun font from linux
- add 12x22 console simple font test
Modern mobile phones typically have high pixel density.
Bootmenu is hardly readable on those with 8x16 font.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Modern mobile phones typically have high pixel density.
Bootmenu is hardly readable on those with 8x16 font.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow font size configuration at runtime for console_simple.c
driver. This needed for unit testing different fonts.
Configuring is done by `font` command, also used for font
selection in true type console.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since multiple vidconsole drivers exists, vidconsole_get_font_size()
implementation cannot longer live in vidconsole_uclass.c file.
Move current vidconsole_get_font_size logic to truetype driver ops.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This needed for unit testing different fonts.
Configured fonts are placed in an array of fonts.
First font is selected by default upon console probe.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[agust: fixed build error when bmp logo disabled]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Devices with high ppi may benefit from wider fonts.
Current width implementation is limited by 1 byte, i.e. 8 bits.
New version iterates VIDEO_FONT_BYTE_WIDTH times, to process all
width bytes, thus allowing fonts wider than 1 byte.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- move common code to vidconsole_internal.h and console_core.c
- unite probe functions
- get rid of code duplications in switch across bpp values
- extract common pixel fill logic in two functions one per
horizontal and vertical filling
- rearrange statements in put_xy* methods in unified way
- replace types - uint*_t to u*
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As the file spear_sdhci.c file is already removed, delete the associated
configuration CONFIG_MMC_SDHCI_SPEAR.
Fixes: c942fc925e ("mmc: spear: remove the entire spear_sdhci.c file")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
According to the PLL vendor, we should keep the PLL power on, so we
shouldn't toggle the power-down bit during PLL initialization.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
According to the PLL vendor, we should keep the PLL power on, so we
shouldn't toggle the power-down bit during PLL initialization.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
The fttmr010 timer driver was deleted by
commit 29fc6f2492 ("ARM: remove a320evb board support")
The original source file was: arch/arm/cpu/arm920t/a320/timer.c
Return the driver to the codebase in a DM compatible form.
A platform using fttmr010 will be submitted later.
This hardware is described in the datasheet [1], starting from page 348.
According to the datasheet, there is a Revision Register at offset 0x3C,
which is not present in 'struct fttmr010'. Add it and debug() print
revision in probe function.
[1]
https://bitbucket.org/Kasreyn/mkrom-uc7112lx/src/master/documents/FIC8120_DS_v1.2.pdf
Signed-off-by: Sergei Antonov <saproj@gmail.com>
- Partial merge of a series of mine to select some framework options
that shouldn't be prompted for (and remove some unused code related to
that), and a partial merge of a series from Simon to remove some dead
code and address various CONFIG_IS_ENABLED/IS_ENABLED issues in code.
Add a new SPL_PHY_ATHEROS to avoid a build error on am335x_evm with split
config.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
At present we enable the sandbox I2C driver for all builds. Add a separate
Kconfig option to control this, so that it can be disabled in TPL, where
it is not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
At present we enable the sandbox RTC driver for all builds. Add a separate
Kconfig option to control this, so that it can be disabled in TPL, where
it is not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_PHY_FIXED defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_MULTIPLEXER defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_DISPLAY_AER_FULL defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not used since time out of mind.
Drop the driver and Kconfig option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
There are 4 USB controllers on MT8195, the controllers (IP1~IP3,
exclude IP0) have a wrong default SOF/ITP interval which is
calculated from the frame counter clock 24Mhz by default, but
in fact, the frame counter clock is 48Mhz, so we shall set the
accurate interval according to 48Mhz for those controllers.
Note:
The first controller no need set it, but if set it, shall change
tphy's pll at the same time.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The T-PHY controller is designed to use use PLL integer mode, but
in fact use fractional mode for some ones on mt8195 by mistake,
this causes signal degradation (e.g. eye diagram test fail), fix
it by switching PLL to 26Mhz from default 48Mhz to improve signal
quality.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Prefer to make use of FIELD_PREP() macro to prepare bitfield value,
then no need local macros anymore.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Imply means you can turn off the option and expect things to work
- "it's a good idea to have X enabled" is when to use imply
- "you must have X for Y to work" is when to use select
Use "select" here.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Building sandbox_defconfig with CONFIG_SPL_TIMER=y results in an error
include/dm/platdata.h:63:33: error: static assertion failed:
"Cannot use U_BOOT_DRVINFO with of-platdata.
Please use devicetree instead"
Add a missing condition in the sandbox driver.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, pinctrl drivers are getting probed during post-bind, however
that is being reverted, and on A37XX pinctrl driver is the one that
registers the GPIO driver during the probe.
So, if the pinctrl driver doesn't get probed GPIO-s won't get registered
and thus they cannot be used.
This is a problem on the Methode eDPU as it just uses SB pins as GPIO-s
and without them being registered networking won't work as it only has
one SFP slot and the TX disable GPIO is on the SB controller.
So, lets just add a flag only to A37XX driver to probe after binding
in order for the GPIO driver to always get registered.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new Kconfig option CONFIG_MVEBU_SPL_BOOT_DEVICE_NAND which instruct
make to generate kwbimage with NAND header. This image is used for booting
from NAND flash (either SPI or parallel).
Support is very simple, SPL after finishes DDR training returns back to the
BootROM (via CONFIG_SPL_BOOTROM_SUPPORT option) and BootROM then loads and
executes U-Boot proper.
To generate correct kwbimage NAND header, it is required to set following
Kconfig options:
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_MVEBU_SPL_NAND_BADBLK_LOCATION
They are used only by make / mkimage when generating final kwbimage.
CONFIG_MVEBU_SPL_NAND_BADBLK_LOCATION is a new mvebu specific Kconfig
option which is set into kwbimage NAND_BADBLK_LOCATION header field.
Signed-off-by: Pali Rohár <pali@kernel.org>
-----BEGIN PGP SIGNATURE-----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=6a0G
-----END PGP SIGNATURE-----
Merge tag 'tpm-next-28022023' of https://source.denx.de/u-boot/custodians/u-boot-tpm into next
TPM auto startup and testing:
Due to U-Boot's lazy binding we always relied on command line tools to
initialize the TPM subsystem and devices. One exception is the EFI
subsystem. When compiled with TCG2 measured boot support the TPM was
automatically initialized.
However that init was not complete. The TCG specs [0] (and specifically
§12.3 Self-test modes) describe how self-tests on the device should be
performed. This PR is adding an extra API function, that can be used to
initialize the TPM2.0 properly.
Simon added the equivalent for TPM1.2 and refactored the DM tests to
include the new funtion.
[0] https://trustedcomputinggroup.org/wp-content/uploads/TPM-Rev-2.0-Part-1-Architecture-01.07-2014-03-13.pdf
- mark reserved blocks from Ashok Reddy Soma
- backport BRCMNAND changes from Linux from Linus Walleij
- fix display of unknown raw ID from Patrice Chotard
- show reserved block in chip.erase from Michael Trimarchi
-----BEGIN PGP SIGNATURE-----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=0HB0
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20230227' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash into next
Pull request for u-boot-nand-20230227
- mark reserved blocks from Ashok Reddy Soma
- backport BRCMNAND changes from Linux from Linus Walleij
- fix display of unknown raw ID from Patrice Chotard
- show reserved block in chip.erase from Michael Trimarchi
SDHCI driver may attempt to set 26MHz clock, but clk_rk3568
will return error in this case. Apparently, SDHCI silently ignores the
error and as a result eMMC initialization fails.
Add 25 MHz and 26 MHz clk rates for sdmmc and emmc on rk3568 to fix that.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for rk3066a, rk3188, rk322x and rk3288 compatible.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Refactor the driver to use driver data and ops to simplify handling
of SoCs that require a unique read op.
Move handling of the aligned bounce buffer to main read op in order to
keep the SoC unique read op simple.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
