- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
Header file mach/cpu.h already defines MBUS_PCI_MEM_SIZE macro which
defines size of MBUS_PCI_MEM_BASE window. So use global MBUS_PCI_MEM_SIZE
macro instead of locally defined PCIE_MEM_SIZE macro. Both macros have same
definition.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
In the current code, it doesn't reset the cursors of LUT entry and
StreamID at the beginning of the fixup, so it can result in LUT entry
setup and msi-map mismatch and LUT entries and StreamID leaking
when reload and fixup the DTB.
This patch move the initialization of LUT entry and StreamID cursors
to the beginning of the fixup to resolve the issues.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The official bindind of the PCIe controller of the ls1028a has the
following compatible string:
compatible = "fsl,ls1028a-pcie";
Additionally, the resource names and count are different. Update the
driver to support this binding and change the entry in the ls1028a
device tree.
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
According to the Armada 3720 Functional Specification Data Strobe applies
for both read and write config requests.
Data strobe bits configure which bytes from the start address should be
returned for read request. Set value 0xf (all 4 bits) into Data Strobe
register to read all four bytes from specified 32-bit config space
register. Same value for Data Strobe register is programmed by Linux
pci-aardvark.c driver for config read requests.
Without this patch pci-aardvark driver sets data strobe register only
during config write operations. So any followup config read operations
could result with just partial datai returned (if previous write operation
was not 32-bit wide). This patch fixes it and ensures that config read
operations always read all bytes from requested register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a pci driver, not an eth driver.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Root Complex should be the default mode, let's set it explicitly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge is working, U-Boot's CONFIG_PCI_PNP code automatically
enables memory access and bus mastering when it is needed. So do not
prematurely enable memory access and bus mastering.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI Bridge is always accessible also when link is down. So move detection
of link up from mvebu_pcie_of_to_plat() function to mvebu_pcie_valid_addr()
function which is used when accessing PCI config space.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Functions mvebu_pcie_get_local_bus_nr() and mvebu_pcie_get_local_dev_nr()
are not used, so remove them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The mysterious "Memory controller" PCI device which is present in PCI
config space is improperly configured and crippled PCI Bridge which acts
as PCIe Root Port for endpoint PCIe card.
This PCI Bridge reports in PCI config space incorrect Class Code (Memory
Controller) and incorrect Header Type (Type 0). It looks like HW bug in
mvebu PCIe controller but apparently it can be changed via mvebu registers
to correct values.
The worst thing is that this PCI Bridge is crippled and its PCI config
registers in range 0x10-0x34 alias access to internal mvebu registers which
have different functionality as PCI Bridge registers. Moreover,
configuration of PCI primary and secondary bus numbers (registers 0x18
and 0x19) is done via totally different mvebu registers via totally strange
method and cannot be done via PCI Bridge config space.
Due to above fact about PCI config range 0x10-0x34, allocate a private
cfgcache[] buffer in the driver, to which PCI config access requests to
the 0x10-0x34 space will be redirected in mvebu_pcie_read_config() and
mvebu_pcie_write_config() functions. Function mvebu_pcie_write_config()
will also catch writes to PCI_PRIMARY_BUS (0x18) and PCI_SECONDARY_BUS
(0x19) registers and set PCI Bridge primary and secondary bus numbers via
mvebu's own method.
Also, Expansion ROM Base Address register (0x38) is available, but at
different offset 0x30. So recalculate register offset before accessing PCI
config space.
After these steps U-Boot sees working PCI Bridge and CONFIG_PCI_PNP code
can finally start enumerating all PCIe devices correctly, even with more
complicated PCI topology. So update also mvebu_pcie_valid_addr() function
to reflect state of the real device topology.
Each PCIe port is de-facto isolated and every PCI Bridge which is part of
PCIe Root Complex is also isolated, so put them on separate PCI buses as
(local) device 0.
U-Boot already supports enumerating separate PCI buses, real (HW) bus
number can be retrieved by "PCI_BUS(bdf) - dev_seq(bus)" code, so update
config read/write functions to properly handle more complicated tree
topologies (e.g. when a PCIe switch with multiple PCI buses is connected
to the PCIe port).
Local bus number and local device number on mvebu are used for determining
which config request type is used (Type 0 vs Type 1). On normal non-broken
PCIe hardware it is done by primary and secondary bus numbers. So correctly
translate settings between these numbers to ensure that correct config
requests are sent over the PCIe bus.
As bus numbers are correctly re-configured, it does not make sense to print
some initial bogus configuration during probe, so remove this debug code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
When reading 8 or 16 bits from config space, use appropriate readb() or
readw() calls. This ensures that PCIe controller does not read more bits
from endpoint card as asked by read_config() function.
Technically there should not be an issue with reading data from config
space which are not later used as there are no clear-by-read registers.
But it is better to use correct read operation based on requested size.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Current implementation of write_config() is broken for PCI_SIZE_8 or
PCI_SIZE_16 as it always uses writel(), which means that write operation
is always 32-bit, so upper 24 bits for PCI_SIZE_8 and upper 16 bits for
PCI_SIZE_16 are cleared.
Fix this by using writeb() and writew(), respectively.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
As stated in comment above the code, CRS response can be returned to OS
only for 4-byte PCI_VENDOR_ID config read request. So fix the code.
Fixes: 1d7ad68559 ("arm: a37xx: pci: Handle propagation of CRSSVE bit from PCIe Root Port")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI Bridge which represents Aardvark PCIe Root Port does not have
configurable bars.
So ensure that write operation to bars registers on PCI Bridge is noop and
bars registers always contain zero address which indicates that bars are
unsupported.
After this change U-Boot 'pci bar 0.0.0' command does not show any
allocated bars for PCI Bridge device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: cb056005dc ("arm: a37xx: pci: Add support for accessing PCI Bridge on root bus")
Reviewed-by: Stefan Roese <sr@denx.de>
Function dm_pci_hose_probe_bus() expects that bus is valid PCI device with
Bridge header type (0x01). So add check before touching PCI config space to
prevent misconfiguring some non-standard device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI Rom Address is currently supported only for Normal (0x00) and
Bridge (0x01) header types. Fix code accordingly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There were several changes for this structure but the documentation was
not changed at the time. Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge (PCIe Root Port) for Aardvark is emulated in U-Boot,
add support for handling and propagation of CRSSVE bit.
When CRSSVE bit is unset (default), driver has to reissue config
read/write request on CRS response.
CRSSVE bit is supported only when CRSVIS bit is provided in read-only
Root Capabilities register. So manually inject this CRSVIS bit into read
response for that register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge is working for the PCIe Root Port, U-Boot's PCI_PNP
code automatically enables memory access and bus mastering when needed.
We do not need to enable it when setting the HW up.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Aardvark does not have a real PCIe Root Port device on the root bus.
Instead it has PCIe registers of PCIe Root Port device mapped in
internal Aardvark memory space starting at offset 0xc0.
The PCIe Root Port itself is normally available as a PCI Bridge device
on the root bus with bus number zero. Aardvark instead has the
configuration registers of this PCI Bridge at offset 0x00 of Aardvark's
memory space, but the class code of this device is Mass Storage
Controller (0x010400), instead of PCI Bridge (0x600400), which causes
U-Boot to fail to recognize it as a P2P Bridge
Add a hook into the pcie_advk_read_config() / pcie_advk_write_config()
functions to redirect access for root bus from PIO transfer to this
internal Aardvark memory space. This will allow U-Boot to access
configuration space of this PCI Bridge which represents PCIe Root Port.
Redirect access to PCI Bridge registers in range 0x10 - 0x34 to driver's
internal buffer (cfgcache[]). This is because at those addresses
Aardvark has different registers, incompatible with config space of a
PCI Bridge.
Redirect access to PCI Bridge register PCI_ROM_ADDRESS1 (0x38) to
Aardvark internal address for that register (0x30).
When reading PCI Bridge register PCI_HEADER_TYPE, set it explicitly to
value Type 1 (PCI_HEADER_TYPE_BRIDGE) as PCI Bridge must be of Type 1.
When writing to PCI_PRIMARY_BUS or PCI_SECONDARY_BUS registers on this
PCI Bridge, correctly update driver's first_busno and sec_busno
variables, so that pcie_advk_addr_valid() function can check if address
of any device behind the root bus is valid and that PIO transfers are
started with correct config type (1 vs 0), which is required for
accessing devices behind some PCI bridge after the root bus.
U-Boot's PCI_PNP code sets primary and secondary bus numbers as relative
to the configured bus number of the root bus. This is done so that
U-Boot can support multiple PCIe host bridges or multiple root port
buses, when internal bus numbers are different.
Now that root bus is available, update code in pcie_advk_read_config()
and pcie_advk_write_config() functions to correctly calculate real
Aardvark bus number of the target device from U-Boot's bus number as:
busno = PCI_BUS(bdf) - dev_seq(bus)
Stefan: Small fix of header masking as suggested by Pali.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Aardvark reports Disabled and Hot Reset LTSSM states as values >= 0x20.
Link is not up in these states, so fix pcie_advk_link_up() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
On Amlogic A311D, when the PCIe link fails disabling the related clocks
makes USB fail. For an unknown reason, this doesn happen on the S905D3 SoC.
Mimic the Linux behavior by not considering a link failure a probe failure,
and continue even if the PCIe link is down.
Reported-by: Art Nikpal <email2tema@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The function prototype for ft_pci_setup is inside fdt_support.h, we need
to include that header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid a build warning with W=1, provide a function prototype for
dm_pciauto_prescan_setup_bridge, which is a non-static function whose
definition is inside pci_auto.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some PCIe controller's read_config() method support indicating error
directly via return value, but some cannot distinguish all-ones (or
all-zeros) read response from an error.
The current code in pci_bind_bus_devices() interprets all-ones /
all-zeros in PCI_VENDOR_ID register as "nothing connected", and
continues the cycle, but an error returned via return value breaks the
cycle.
This is wrong for the PCIe controllers which return this error via
return value.
Handle all errors when reading PCI_VENDOR_ID the same way.
This fixes enumeration of PCI devices for example when there is a PCI
bridge connected behind another PCI bridge and not all ports are
connected to a device, and the controller (for example Aardvark)
translates the UR error (Unsupported Request) as -EOPNOTSUPP.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Lower 4 bits of PCI_MEMORY_BASE and PCI_MEMORY_LIMIT registers are reserved
and should be zero. So do not set them to non-zero value.
Lower 4 bits of PCI_PREF_MEMORY_BASE and PCI_PREF_MEMORY_LIMIT registers
contain information if 64-bit memory addressing is supported. So preserve
this information when overwriting these registers.
Lower 4 bits of PCI_IO_BASE and PCI_IO_LIMIT register contain information
if 32-bit io addressing is supported. So preserve this information and do
not try to configure 32-bit io addressing (via PCI_IO_BASE_UPPER16 and
PCI_IO_LIMIT_UPPER16 registers) when it is unsupported.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
With legacy PCI code removed and thus DM_PCI also removed, a few places
did not get correctly updated with the merge to next and thus broke.
Remove now extraneous dependencies on DM_PCI.
Signed-off-by: Tom Rini <trini@konsulko.com>
Use dev_dbg() instead of dev_err() in pcie_advk_check_pio_status().
For example CRS is not an error status, it just says that the request
should be retried.
Without this, U-Boot spams the terminal with
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x100000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x108000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x110000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x120000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x128000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x130000
...
when a device is not connected to a PCIe switch (Unsupported Request
from the switch).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
According to PCIe base specification, if CRS Software Visibility is not
enabled, the Root Complex must re-issue the Configuration Request as a new
Request.
Normally this part of Root Complex is implemented in hardware but aardvark
is somehow special and does not implement it in hardware and expect that
handling of config requests are fully implemented in software.
This re-issuing functionality is required also because U-Boot does not
support CRS Software Visibility feature and therefore expects that Root
Complex re-issues requests as is specified in PCIe base specification.
Retry / re-issue config request up to the PIO_MAX_RETRIES, to prevent
infinite loop. After retry count exceed PIO_MAX_RETRIES, returns failure.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There was mistake in commit 4cd61c43fd ("arm: a37xx: pci: Fix handling
PIO config error responses"). U-Boot does not support handling of CRS
return value for PCI_VENDOR_ID config read request and also does not set
CRSSVE bit.
Therefore disable returning CRS response for now.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 4cd61c43fd ("arm: a37xx: pci: Fix handling PIO config error responses")
Reviewed-by: Stefan Roese <sr@denx.de>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
Returning fabricated CRS value (0xFFFF0001) by PCIe Root Complex to OS is
allowed only for 4-byte PCI_VENDOR_ID config read request and only when
CRSSVE bit in Root Port PCIe device is enabled. In all other error PCIe
Root Complex must return all-ones.
So implement this logic in pci-aardvark.c driver properly.
aardvark HW does not have Root Port PCIe device and U-Boot does not
implement emulation of this device. So expect that CRSSVE bit is set as
U-Boot can already handle CRS value for PCI_VENDOR_ID config read request.
More callers of pci_bus_read_config() function in U-Boot do not check for
return value, but check readback value. Therefore always fill readback
value in pcie_advk_read_config() function. On error fill all-ones of
correct size as it is required for PCIe Root Complex.
And also correctly propagates error from failed config write request to
return value of pcie_advk_write_config() function. Most U-Boot callers
ignores this return value, but it is a good idea to return correct value
from function.
These issues about return value of failed config read requests, including
special handling of CRS were reported by Lorenzo and Bjorn for Linux kernel
driver pci-aardvark together with quotes from PCIe r4.0 spec, see details:
https://lore.kernel.org/linux-pci/20210624213345.3617-1-pali@kernel.org/t/#u
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>