Move board/revision specific dt fixups for WDOG and UHS-I features
so that we can call them early for U-Boot control dt as well.
Additionally drop a deprected non-mainline dt-prop fixup regarding
HDMI input format.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable driver model support for FEC ethernet which allows us to remove
the iomux and board_eth_init function. Replace the toggling of the ethernet
phy reset with dt configuration.
Enable driver model support for PCI which allows us to remove the
eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
PCI devices on init such as the e1000 that is present on the GW552x.
Convert board_pci_fixup to use dm callback and remove pcidisable env
variable which is not supported for DM_PCI and thus leave PCI always
enabled during init.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable dm support for USB (which also requires dm support for fixed
regulators used for vbus enable) and remove usb iomux which is no
longer needed.
We can remove the handling of otgpwr_en gpio as this is defined in
dt as usbotg vbus-supply but we need to keep the handling of
USB_HUB_RST# for boards that have a USB HUB as that isn't defined in
the dt's currently.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Do not setup I2C3 in the SPL for Ventana as some devices on that bus
(aic3x codecs) can hang the bus causing i2c_setup to spin endlessly until
they are put into reset. Removing the setup of I2C3 from the SPL allows
the board-specific GPIO to be configured to take care of putting codecs
in reset prior to U-Boot setting up I2C3.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
UHS-I support is available on Ventana boards with micro-SD sockets depending
on the board revision. For backwards compatibility to not break users
who have old bootloaders and newer kernels the device-tree on boards with
microSD disables UHS-I support by default by defining the no-1-8-v property
in the esdhc controller node. For models/revisions that support switchable
1.8V/3.3V I/O which is detectable by the presence of a pull-down on the
SD3_VSELECT pin we remove that property to enable support in the kernel.
Additionally we add SD3_VSELECT to the pinmux for clarity (even though U-Boot
does not currently support UHS-I modes requiring 1.8V I/O).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The MSATA feature is a board-specific feature on Gateworks Ventana boards.
In most cases a 2:1 mux will steer either PCIe or SATA to a miniPCIe socket
through an MSATA_EN gpio. In these such cases assign the gpio in the board
specific struct and use its presence to determine if we default the GPIO to
PCIe and if we later steer it according to hwconfig.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
- Added iomux for CAN_STBY and RS484_TEN (GW52xx/GW53xx/GW54xx/GW551x)
- Moved iomux of USBHUB_RST# out of board_ehci_hcd_init so that it is
done regardless of USB being initialized in bootloader
- Added usb_sel iomux/hwconfig for GW552x
- Fixed mezzanine DIO for GW54xx
- Fixed PANLEDR# for GW54xx
- Fixed dio iomux/hwconfig for GW552x
- Fixed dio iomux for GW551x
- removed redundant #define
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Avoid requiring board-model and probe pmic by its i2c address.
This is in preparation for being able to call pmic_setup() from SPL
and not need board type.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Move shared functions used by both SPL and U-Boot to common.c:
- setup_iomux_uart() and uart pad config
- gpio pad config
In the process also moved the following to common.c in preparation for
calling it from the SPL:
- split i2c setup into a shared function
- move pmic init to setup_pmic() function to call directly from
power_init_board()
- split gpio setup into early (iomux and default pin config)
and late (output configuration based on env)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
