Note this is a tree-wide change affecting multiple architectures.
At present we use __bss_start, but mostly __bss_end__. This seems
inconsistent and in a number of places __bss_end is used instead.
Change to use __bss_end for the BSS end symbol throughout U-Boot. This
makes it possible to use the asm-generic/sections.h file on all
archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
DMM_LISA_MAP registers program whether memory is mapped
on particular EMIF or not. Irrespective of these registers
EMIF is getting configured. Correcting the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Git commit d417d1db5f replaced the
omap-common file reset.S with reset.c, but the Makefile was not
adjusted for that.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Include asm/arch/sys_proto.h for gpmc_init prototype.
Without this we get a warning while building for AM335x.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Add section for the linker-generated lists into all possible linker
files, so that everyone can easily use these lists. This is mostly
a mechanical adjustment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
U-boot should not ignore getting the bootmode passed on from the bootrom.
With this, U-boot SPL knows it was loaded from MMC1 and use this info to
read full U-boot from MMC1 as well.
Cc: pprakash@ti.com
Cc: trini@ti.com
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
We move the spl_nand_load_image function to common/spl. This will allow
for easier integration of SPL-boots-Linux code on other arches.
Signed-off-by: Tom Rini <trini@ti.com>
In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer,
clear the BSS and call board_init_r. We mark this as weak as some
platforms may need to perform additional initalization at this point.
We provide a gd that we know will be in a usable location, once the BSS
has been cleared to help with this as well. Finally, we no longer call
relocate_code so remove that from the armv7 version.
Next, both board_init_f and jump_to_image_linux are going to be
inherently arch-specific, so move these versions to arch/arm/lib/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards. We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave
the NAND one in-place as we plan to replace it later in this series.
We use common/spl to avoid linker problems with respect to merging
constant strings in objects. Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.
Signed-off-by: Tom Rini <trini@ti.com>
This is an OMAP/related-specific function, move calling it to
spl_board_init() and turn on CONFIG_SPL_BOARD_INIT on the boards that
enabled NAND and didn't enable this already.
Signed-off-by: Tom Rini <trini@ti.com>
- Remove includes we don't need
- Switch some printf statements to puts
- Convert some printf statements to debug, introduce new puts statements
- In most cases saying just "No mkimage signature, assuming
u-boot.bin" or similar is sufficient. This also means the non-DEBUG
case doesn't need printf, in the core of SPL.
- The other case here is that PLAIN_VERSION provided what we wanted
already, so just use it.
Signed-off-by: Tom Rini <trini@ti.com>
Move the default omap/related-centric board_mmc_init to
arch/arm/cpu/armv7/omap-common/boot-common.c and move the type defines
to <asm/spl.h>. Also use mmc->read_bl_len rather than MMCSD_SECTOR_SIZE
Signed-off-by: Tom Rini <trini@ti.com>
Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and
add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK.
Signed-off-by: Tom Rini <trini@ti.com>
We can only attempt to setup a malloc pool if
CONFIG_SYS_SPL_MALLOC_START is defined, and not all boards require it.
Make the call depend on the define.
Signed-off-by: Tom Rini <trini@ti.com>
Only omap4/5 currently have a meaningful set of display text and overo
had been adding a function to display nothing. Change how this works to
be opt-in and only turned on for omap4/5 now.
Signed-off-by: Tom Rini <trini@ti.com>
Make the lowlevel_init function that these platforms have which just
sets up the stack and calls a C function available to all armv7
platforms. As part of this we change some of the macros that are used
to be more clear. Previously (except for am335x evm) we had been
setting CONFIG_SYS_INIT_SP_ADDR to a series of new defines that are
equivalent to simply referencing NON_SECURE_SRAM_END. On am335x evm we
should have been doing this initially and do now.
Cc: Sricharan R <r.sricharan@ti.com>
Tested-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch uses the code in omap-common to support gpio modules 1-3
on am33xx based boards.
It adds base address and register definitions, enables clocks to the
modules, and enables building the common gpio code for CONFIG_AM33XX
as well as CONFIG_OMAP
Signed-off-by: Steve Sakoman <steve@sakoman.com>
The external phy is present in the case OMAP5 soc is currently
configured in emif-common.c. This results in having dummy structures
for those Socs which do not have a external phy. So by having a weak
function in emif-common and overriding it in OMAP5, avoids the use
of dummy structures.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Code currently tests for <= 0xff. Micron manufacturer code is 0xff, so
Micron memory will not be detected!
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Some rams (Micron for example) return duplicate mr data on all byte lanes.
Users of the get_mr function currently don't deal with this duplicated
data gracefully. This patch detects the duplicated data and returns only
the expected 8 bit mr data.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Errata ID:i727
Description: The refresh rate is programmed in the EMIF_SDRAM_REF_CTRL[15:0]
REG_REFRESH_RATE parameter taking into account frequency of the device.
When a warm reset is applied on the system, the OMAP processor restarts
with another OPP and so frequency is not the same. Due to this frequency
change, the refresh rate will be too low and could result in an unexpected
behavior on the memory side.
Workaround:
The workaround is to force self-refresh when coming back from the warm reset
with the following sequence:
• Set EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE to 0x2
• Set EMIF_PWR_MGMT_CTRL[7:4] REG_SR_TIM to 0x0
• Do a dummy read (loads automatically new value of sr_tim)
This will reduce the risk of memory content corruption, but memory content
can't be guaranteed after a warm reset.
This errata is impacted on
OMAP4430: 1.0, 2.0, 2.1, 2.2, 2.3
OMAP4460: 1.0, 1.1
OMAP4470: 1.0
OMAP5430: 1.0
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
EMIF and DDR device state are preserved in warmreset. Redoing the full
initialisation would cause unexpected behaviour. Do only partial
initialisation to account for frequency change.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Certain modules are not affected by means of
a warm reset and need not be configured again.
Adding an API to detect the reset reason warm/cold.
This will be used to skip the module configurations
that are retained across a warm reset.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
In OMAP5432 EMIF controlller supports DDR3 device.
This patch adds support for ddr3 device intialization and configuration.
Initialization sequence is done as specified in JEDEC specs.
This also adds support for ddr3 leveling.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
get_ram_size checks the given memory range for valid ram,
but expects the size of memory to be aligned to the power
of 2. In case of OMAP5 evm board the memory available is
2GB - 16MB(used for TRAP section) = 2032MB.
So always ensure that the size of memory used for testing is
aligned to the power of 2.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The DMM sections can be overlapping with each other, with
sections 3 to 0 having the highest to lowest priority in that
order. There could also be a section that is used trap the
unmapped Tiler entries and this trap section could be
overlapping with the actual sdram area.
So take care of the above scenarios while calculating the
size of the actual ram.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Use ENTRY and ENDPROC with assembly functions to ensure
necessary assembler directives for all functions.
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The reset.S has the function to do a warm reset on OMAP
based socs. Moving this to a reset.c file so that this
acts a common layer to add any reset related functionality
for the future.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The nominal opp vdd values as recommended for
ES1.0 silicon is set for mpu, core, mm domains using palmas.
Also used the right sequence to enable the vcores as per
a previous patch from Nishant Menon, which can be dropped now.
http://lists.denx.de/pipermail/u-boot/2012-March/119151.html
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The OMAP5 silicon has new DDR PHY design, which includes a external PHY
as well. So configuring the ext PHY parameters here. Also the EMIF timimg
registers and a couple of DDR mode registers needs to be updated based on
the testing from the actual silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Aligning all the clock related settings like the dpll frequencies, their
respective clock outputs, etc to the ideal values recommended for
OMAP5430 ES1.0 silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
|---------------| (SET1 default 1.4V)
| --------(programmed voltage)
| <- (This switch happens on mux7,pullup)
vdd_mpu(TPS) -----/ (OPP boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -----------------------/ (OPP boot voltage)
Problem 1) |<----- Tx ------>|
timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.
By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
-------- (programmed voltage)
vdd_mpu(TPS) ------------/ (Opp boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -------------/ (OPP boot voltage)
NOTE: This does not attempt to address OMAP5 - Aneesh please confirm
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
OMAP Voltage controller is used to generically talk to
PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code
in multiple SoC code, introduce a common voltage controller
logic which can be re-used from elsewhere.
With this change, we replace setup_sri2c with omap_vc_init which
has the same functionality, and replace the voltage scale
replication in do_scale_vcore and do_scale_tps62361 with
omap_vc_bypass_send_value. omap_vc_bypass_send_value can also
now be used with any configuration of PMIC.
NOTE: Voltage controller controlling I2C_SR is a write-only data
path, so no register read operation can be implemented.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency. While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
