Commit graph

79731 commits

Author SHA1 Message Date
Michael Trimarchi
37a7c374a6 arm: mach-imx: cmd_nandbcb fix bad block handling
The badblock should be skipped properly in reading and writing.
Fix the logic. The bcb struct is written, skipping the bad block,
so we need to read using the same logic. This was tested create
bad block in the area and then flash it and read it back.

Acked-by: Han Xu <han.xu@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
2022-05-20 12:36:48 +02:00
Michael Trimarchi
a222c14792 mtd: nand: mxs_nand_spl: Fix bad block skipping
The specific implementation was having bug. Those bugs are since
the beginning of the implementation. Some manufactures can already
experience this bug in their SPL code. This bug can be more visible on
architecture that has complicated boot process like imx8mn. Older
version of uboot can be affected if the bad block
appear in correspoding of the beginning of u-boot image. In order to
adjust the function we scan from the first erase block.

The problematic part of old code was in this part:

while (is_badblock(mtd, offs, 1)) {
           page = page + nand_page_per_block;
          /* Check i we've reached the end of flash. */
          if (page >= mtd->size >> chip->page_shift) {
                      free(page_buf);
                      return -ENOMEM;
         }
}

Even we fix it adding increment of the offset of one erase block size
, we don't fix the problem, because the first erase block where the
image start is not checked. The code was tested on an imx8mn where
the boot rom api was not able to skip it. This code is used by other
architecures like imx6 and imx8mm

Cc: Han Xu <han.xu@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
2022-05-20 12:36:47 +02:00
Michael Trimarchi
78bf8e802c nand: raw: mxs_nand: Fix specific hook registration
Move the hook after nand_scan_tail is called. The hook must be replaced
to the mxs specific one but those must to be assignment later in the
probe function.

With this fix markbad is working again. Before this change:

nand markbad 0xDEC00
NXS NAND: Writing OOB isn't supported
NXS NAND: Writing OOB isn't supported
block 0x000dec00 NOT marked as bad! ERROR 0

Cc: Han Xu <han.xu@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
2022-05-20 12:36:47 +02:00
Gaurav Jain
1919f58a8f crypto/fsl: fsl_hash: Fix dcache issue in caam_hash_finish
HW accelerated hash operations are giving incorrect hash output.
so add flush and invalidate for input/output hash buffers.

Fixes: 94e3c8c4fd (crypto/fsl - Add progressive hashing support using hardware acceleration.)
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
2022-05-20 12:36:47 +02:00
Gaurav Jain
cad77280c3 i.MX8ULP: add display_ele_fw_version api
implement get f/w version api.
print ele f/w version in spl.

Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@nxp.com>
2022-05-20 12:36:47 +02:00
Ye Li
cda8f87349 caam: Fix crash in case caam_jr_probe failed
If probing caam_jr returns failure, the variable "dev" will not be
initialized, so we can't use dev->name for the error print.
Otherwise it will cause crash.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
2022-05-20 12:36:47 +02:00
Fabio Estevam
5ed4c33f36 kontron-sl-mx8mm: Select the CONFIG_CMD_UNZIP option
Select the CMD_UNZIP option so that the 'gzwrite' command
can be used to flash wic.gz image into the eMMC.

Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2022-05-20 12:36:47 +02:00
Peng Fan
8494fe077c imx: toradex/verdin-imx8mm/p: cleanup board watchdog code
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:29 +02:00
Peng Fan
a6924c95d1 imx: verdin-imx8mm/p: cleanup board watchdog code
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:29 +02:00
Peng Fan
09bf8270cf imx: imx8mn_smm_s2: clean up board watchdog code
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
2022-05-20 09:30:29 +02:00
Peng Fan
0726bdd460 imx: imx8mm-mx8menlo: drop unneeded watchdog settings
pinctrl_wdog as u-boot,dm-spl already marked in imx8mm-verdin-u-boot.dtsi,

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2022-05-20 09:30:29 +02:00
Peng Fan
a38ed61643 imx: imx8mp_evk: enable pinctrl_wdog in SPL
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:29 +02:00
Peng Fan
ba06ea8991 imx: imx8mm_evk: enable pinctrl_wdog in SPL
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:29 +02:00
Peng Fan
6d5cc90670 imx: imx8mn_evk: enable pinctrl_wdog in SPL
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:29 +02:00
Peng Fan
597514e738 imx: imx8mq-phanbell: enable CONFIG_DM_SERIAL
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-05-20 09:30:29 +02:00
Peng Fan
1d8c0c2d7b imx: imx8mq-pico: enable CONFIG_DM_SERIAL
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-05-20 09:30:29 +02:00
Peng Fan
23df340f32 imx: imx8mq-cm: enable CONFIG_DM_SERIAL
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-05-20 09:30:29 +02:00
Peng Fan
56f3888b43 imx: dts: move common changes to imx8mq-u-boot.dtsi
Move some common changes to imx8mq-u-boot.dtsi, so others could reuse it

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-05-20 09:30:29 +02:00
Peng Fan
6ea118ef9a imx: imx8mm_edm_sbc: Enable SPL_DM_SERIAL
Enable CONFIG_SPL_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-05-20 09:30:28 +02:00
Peng Fan
2232d5f5b7 imx: imx8mm_mx8menlo: Enable DM_SERIAL
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-05-20 09:30:28 +02:00
Tim Harvey
d003d89372 board: gateworks: gw_ventana: remove obsolete file
commit 61cf225053 ("board: gateworks: gw_ventana: use comomn GSC driver")
moved to the common GSC driver and moved remaining board-specific
functions to eeprom.c. The functions in gsc.c are no longer used and it
was removed from the Makefile but the file itself was not removed.
Remove it now.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-05-20 09:30:28 +02:00
Tim Harvey
0cba71c1eb board: gateworks: gw_ventana: add support for GPY111 PHY
The MaxLinear GPY111 PHY is being used on some boards due to part
availability. Add support for this PHY which requires a longer reset
post-delay and RGMII delay configuration.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-05-20 09:30:28 +02:00
Tim Harvey
6fc639461b board: gateworks: venice: enable SPL_DM_SERIAL
The uart2 and its pinmux are already marked with u-boot,dm-spl but we
need to move the call to preloader_console_init() after spl_early_init()
to avoid a board hang as dm can't be used until after spl_early_init()
due to the uart driver not enabling the uart clock.

Remove the manual config of the UART pinmux now that it is no longer
needed.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-05-20 09:30:28 +02:00
Tim Harvey
8e3cc42a3f configs: remove FEC_QUIRK_ENET_MAC from imx8m configs
FEC_QUIRK_ENET_MAC is defined in the imx-regs.h include file and thus
does not need to be defined in the various board config includes.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-05-20 09:30:28 +02:00
Tim Harvey
110998f3c6 configs: imx8mp_venice: add FEC_QUIRK_ENET_MAC
The IMX8MP SoC FEC needs to have the FEC_QUIRK_ENET_MAC defined.

Fixes: commit 2395625209 ("board: gateworks: venice: add imx8mp-venice-gw740x support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-05-20 09:30:28 +02:00
Tim Harvey
400eebf10d configs: imx8m{m, n}_venice: remove unneeded CONFIG_FEC_MXC_PHYADDR
The IMX8M based Venice boards all have device-tree fec nodes that
use proper dt with a phy-handle pointing to a phy with reg assigned
to the proper phy address.

There is no need to keep using the CONFIG_FEC_MXC_PHYADDR hack when
a proper dt is used - remove it.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-05-20 09:30:28 +02:00
Peng Fan
a1d675ac77 imx: imx8m: drop uneeded check
All i.MX8M needs TZASC ID SWAP set and locked, no need the check to
waste cpu cycles.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
2022-05-20 09:30:28 +02:00
Peng Fan
5dd9db8f7d imx: imx8m: add rproc_att
With rpoc_att, bootaux able to kick elf file for M core

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:28 +02:00
Peng Fan
40153df63a imx: bootaux: get stack from elf file
To i.MX8, M core stack is pre-coded in source code, so need to get it
before kicking M core. The stack pointer is stored in the first word of
the first PT_LOAD section __isr_vector. So use a num to index the
section loading.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:28 +02:00
Peng Fan
fd60a87e75 imx: bootaux: add missing newline
Add missing newline

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:28 +02:00
Peng Fan
56c2dbdaba imx: bootaux: cleanup code
Use if (CONFIG_IS_ENABLED()) to make code cleaner
Enable elf support for i.MX8M

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:28 +02:00
Rasmus Villemoes
290ffe5788 imx8m: fix reading of DDR4 MR registers
I was trying to employ lpddr4_mr_read() to something similar to what
the imx8mm-cl-iot-gate board is doing for auto-detecting the RAM
type. However, the version in drivers/ddr/imx/imx8m/ddrphy_utils.c
differs from the private one used by that board in how it extracts the
byte value, and I was only getting zeroes. Adding a bit of debug
printf'ing gives me

 tmp = 0x00ffff00
 tmp = 0x00070700
 tmp = 0x00000000
 tmp = 0x00101000

and indeed I was expecting a (combined) value of 0xff070010 (0xff
being Manufacturer ID for Micron). I can't find any documentation that
says how the values are supposed to be read, but clearly the iot-gate
definition is the right one, both for its use case as well as my
imx8mp-based board.

So lift the private definition of lpddr4_mr_read() from the
imx8mm-cl-iot-gate board code to ddrphy_utils.c, and add a declaration
in the ddr.h header where e.g. get_trained_CDD() is already declared.

This has only been compile-tested for the imx8mm-cl-iot-gate
board (since I don't have the hardware), but since I've merely moved
its definition of lpddr4_mr_read(), I'd be surprised if it changed
anything for that board.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-05-20 09:30:28 +02:00
Marek Vasut
c329f9349b ARM: imx: imx31: Introduce and use UART_BASE_ADDR(n)
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-05-20 09:03:01 +02:00
Marek Vasut
be23774ed1 ARM: imx: imx27: Introduce and use UART_BASE_ADDR(n)
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-05-20 09:03:01 +02:00
Marek Vasut
52b6b480db ARM: imx: imx8m: Introduce and use UART_BASE_ADDR(n)
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-05-20 09:03:01 +02:00
Fabio Estevam
16ee0f2afd mx6sllevk: Remove duplicated "mmc dev" command
The "mmc dev ${mmcdev}" command is done twice.

Remove one ocurrence to avoid the duplication.

Signed-off-by: Fabio Estevam <festevam@denx.de>
2022-05-19 21:39:36 +02:00
Fabio Estevam
3df5f19836 mx6slevk: Remove duplicated "mmc dev" command
The "mmc dev ${mmcdev}" command is done twice.

Remove one ocurrence to avoid the duplication.

Signed-off-by: Fabio Estevam <festevam@denx.de>
2022-05-19 21:39:36 +02:00
Gaurav Jain
db74ced5df i.MX8 crypto/fsl: Enable fsl CAAM rng driver
rng driver enabled to read random number using caam.

Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
2022-05-19 21:39:36 +02:00
Marek Vasut
ff04a0944d ARM: dts: imx: Use 100 kHz I2C2 on Data Modul i.MX8M Mini eDM SBC
The I2C2 has SMBus device SMSC USB2514Bi connected to it, the device is
capable of up to 100 kHz operation. Reduce the bus frequency to 100 kHz
to guarantee this I2C device can work correctly.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-05-19 21:39:36 +02:00
Fabio Estevam
d175982c20 imx8mn/8mp: Allow booting via USB
When trying to boot via USB on i.MX8MN it is necessary to specify
the U-Boot environment location, otherwise the boot process simply
hangs.

Specify the environment location when booting from USB.

Tested on a imx8mn-evk.

Suggested-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
2022-05-19 21:39:36 +02:00
Fabio Estevam
7038156447 imx8mn_ddr4_evk: Add USB Mass Storage support
Add USB Mass Storage support, which is a convenient way to flash
the eMMC card, for example.

Signed-off-by: Fabio Estevam <festevam@denx.de>
2022-05-19 21:39:36 +02:00
Gaurav Jain
0c45c77b8a i.MX6SX: crypto/fsl: fix entropy delay value
RNG Hardware error is reported due to incorrect entropy delay

rng self test are run to determine the correct ent_dly.
test is executed with different voltage and temperature to identify the
worst case value for ent_dly. after adding a margin value(1000),
ent_dly should be at least 12000.

Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-05-19 21:39:36 +02:00
Ye Li
9fd406de52 mtd: rawnand: mxs_nand: Fix use_minimum_ecc for spl driver
Because mxs_nand_spl driver does not support DM, to use the minimum ECC
layout, it needs to handle the CONFIG_NAND_MXS_USE_MINIMUM_ECC.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Han Xu <han.xu@nxp.com>
2022-05-19 21:39:36 +02:00
Tom Rini
f83bd23e2a Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- Misc Kconfig cleanups (Chris & Pali)
- turris_omnia: Fix hangup in debug UART (this introduces
  TPL/SPL_DEBUG_UART_BASE) Pali
- mvebu: uDPU: include fixed-phy support (Robert)
- pinctrl: probe pinctrl drivers during post-bind (Robert)
2022-05-18 08:41:13 -04:00
Robert Marko
f9ec791b5e pinctrl: probe pinctrl drivers during post-bind
Currently, pinctrl drivers only get probed if pinconf is actually being
used, however on SoC-s like Armada 3720 pinctrl driver is a also the GPIO
driver.

So, if the pinctrl driver doesn't get probed GPIO-s won't get registered
and thus they cannot be used.

This is a problem on the Methode eDPU as it just uses SB pins as GPIO-s
and without them being registered networking won't work as it only has
one SFP slot and the TX disable GPIO is on the SB controller.

So, probe the pinctrl drivers using DM_FLAG_PROBE_AFTER_BIND like LED
uclass does.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-17 06:44:06 +02:00
Robert Marko
c7111e6ffd mvebu: uDPU: include fixed-phy support
uDPU relies on using fixed-phy for the SFP support, and since the
fixed-phy parsing was moved to the generic driver instead of mvneta
networking stopped working on uDPU with:
uDPU>> dhcp
dm_eth_phy_connect failed

This is due to the conversion commit not enabling fixed-phy support
in defconfig like it did for other boards.

Fixes: 77fcf3cf12 ("net: mvneta: Convert to use PHY_FIXED for fixed-link")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-17 06:44:06 +02:00
Pali Rohár
29dd6e475a arm: mvebu: turris_{omnia,mox}: Enable CONFIG_NETCONSOLE
This allows to use U-Boot console on Turris devices via network.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-17 06:44:06 +02:00
Pali Rohár
5be172819f arm: mvebu: Fix DEBUG_UART_BASE for all 32-bit boards
UART base address is located in internal registers.

Internal registers for 32-bit mvebu boards in SPL are at address 0xd0000000
and in proper U-Boot at address 0xf1000000.

Fix DEBUG_UART_BASE option for all 32-bit mvebu boards.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-17 06:44:06 +02:00
Pali Rohár
2418c1f56f arm: mvebu: turris_omnia: Fix DEBUG_UART_BASE
Internal registers in SPL are at address 0xd0000000 and in proper U-Boot at
address 0xf1000000. UART base address is located in internal registers.

Fix DEBUG_UART_BASE option to correct value for both SPL and proper U-Boot.

This change fixes hangup of proper U-Boot when it is trying to print
something via debug UART.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-17 06:44:06 +02:00
Pali Rohár
d293759d55 serial: ns16550: Add support for SPL_DEBUG_UART_BASE
Use CONFIG_VAL(DEBUG_UART_BASE) instead of CONFIG_DEBUG_UART_BASE, so
proper config value (CONFIG_DEBUG_UART_BASE or CONFIG_SPL_DEBUG_UART_BASE)
is used based on building target.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-17 06:44:06 +02:00