- add more targets for building with buildman:
- avr32
- m68k
and while at it, sort the list alphabetical
Reviewed-by: Roger Meier <r.meier@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Larry Johnson <lrj@acm.org>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Eric Millbrandt <emillbrandt@dekaresearch.com>
They have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Erik Theisen <etheisen@mindspring.com>
They have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stephen Williams <steve@icarus.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We don't want that CONSOLE is redirected to LCD upon init, we rather prefer
that console is still on the serial line.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
The build break was caused by one of my previous commit:
'odroid: defconfig: disable memset at malloc init'
It removes the dts from odroid defconfig - rebase mistake.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Since commit e02ee2548a (kconfig: switch to single .config
configuration), the prefixes in defconfig files such as "+S:",
"+ST:", etc., are meaningless.
This commit was generated by the following command:
find configs -name '*_defconfig' | xargs sed -i 's/^+*S*T*://'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the case of BUILD_NBUILDS > 1, MAKEALL would try to print the size
immediately after the u-boot binary is deleted by the call to:
make -s clean
Move the size print to before the clean
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Panasonic's System LSI products, UniPhier SoC family, have been
transferred to Socionext Inc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Driver Model description in README was removed by commit
65eb659e56 (README: remove description about driver model
configuration options), and was revived by mistake by commit
b79dadf846 when resolving the conflict.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
This should make it more clear why there appear to be C pre-processor
symbols in the file that contain mixed case. They're really error
messages.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When Beagle X15 is connected to Gigabit switch, it takes
more time to finish auto-negotiation than on a 10/100 switch.
The default 4 second limit times-out more often than not. This is
observed when testing with a D-Link DGS-1008A desktop switch.
Increase the auto-negotiation time-out for Beagle-X15 to handle
this case.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
RX51 has a secure logic which uses different parameters compared to
traditional implementation. So, make the generic secure acr write
over-ride-able by board file and refactor rx51 code to use this.
While at it, enable the OMAP3 specific errata code for 454179, 430973,
621766.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the OMAP3 specific errata code for 454179, 430973, 621766
and while at it, remove legacy non-revision checked errata logic.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update to existing recommendation for L2ACTLR configuration to prevent
system instability and optimize performance.
These apply to both OMAP5 and DRA7.
Reported-by: Vivek Chengalvala <vchengalvala@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch enables the workaround for ARM errata 798870 for OMAP5 /
DRA7 which says "If back-to-back speculative cache line fills (fill
A and fill B) are issued from the L1 data cache of a CPU to the
L2 cache, the second request (fill B) is then cancelled, and the
second request would have detected a hazard against a recent write or
eviction (write B) to the same cache line as fill B then the L2 logic
might deadlock."
An l2auxctlr accessor implementation for OMAP5 and DRA7 is introduced
here as well.
Signed-off-by: Praveen Rao <prao@ti.com>
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
omap_smc1 is now generic enough to remove duplicate
omap3_gp_romcode_call logic that omap3 introduced.
As part of this change, move to using the generic lowlevel_init.S for
omap3 as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is in preperation of using generic cross OMAP code.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
set_pl310_ctrl_reg does use the Secure Monitor Call (SMC) to setup
PL310 control register, however, that is something that is generic
enough to be used for OMAP5 generation of processors as well. The only
difference being the service being invoked for the function.
So, convert the service to a macro and use a generic name (same as
that used in Linux for some consistency). While at that, also add a
data barrier which is necessary as per recommendation.
While at this, smc #0 is maintained as handcoded assembly thanks to
various gcc version eccentricities, discussion thread:
http://marc.info/?t=142542166800001&r=1&w=2
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
621766: Under a specific set of conditions, executing a sequence of
NEON or vfp load instructions can cause processor deadlock
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around: Set L1NEON to 1
Based on ARM errata Document revision 20.0 (13 Nov 2010)
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
430973: Stale prediction on replaced inter working branch causes
Cortex-A8 to execute in the wrong ARM/Thumb state
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around: Set IBE to 1
Based on ARM errata Document revision 20.0 (13 Nov 2010)
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
454179: Stale prediction may inhibit target address misprediction on
next predicted taken branch
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around: Set IBE and disable branch size mispredict to 1
Also provide a hook for SoC specific handling to take place if needed.
Based on ARM errata Document revision 20.0 (13 Nov 2010)
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add workaround for Cortex-A15 ARM erratum 798870 which says
"If back-to-back speculative cache line fills (fill A and fill B) are
issued from the L1 data cache of a CPU to the L2 cache, the second
request (fill B) is then cancelled, and the second request would have
detected a hazard against a recent write or eviction (write B) to the
same cache line as fill B then the L2 logic might deadlock."
Implementations for SoC families such as Exynos, OMAP5/DRA7 etc
will be widely different.
Every SoC has slightly different manner of setting up access to L2ACLR
and similar registers since the Secure Monitor handling of Secure
Monitor Call(smc) is diverse. Hence an weak function is introduced
which may be overriden to implement SoC specific accessor implementation.
Based on ARM errata Document revision 18.0 (22 Nov 2013)
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The purpose of this build target is to do SPL over USB RNDIS. We remove
YMODEM, MMC and NAND (and re-set ENV to be built-in) as when those are needed
we can use the other build targets. This brings us well under size limit again.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since commit ad8aae82b2 ("mx6sabre: Enable User Mass Storage") SPL target
does not boot anymore due to the increased spl image size.
Only enable USB Mass Storage for the non-SPL target.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Warp has a DDR eMMC, so enable CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE for better
performance:
reading zImage
5790288 bytes read in 117 ms (47.2 MiB/s)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE should be selected only by boards that really
have a DDR-capable eMMC, so remove this option from common code to avoid
regressions.
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Volodymyr Riazantsev <volodymyr.riazantsev@globallogic.com>
Tested-by: Stefan Roese <sr@denx.de>
By not defining CONFIG_SYS_PROMPT, the standard "=>" prompt is used, so remove
its definition.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Without this patch, the IMX watchdog will not be initialized. And therefor
not active. This patch fixes this by calling hw_watchdog_init() also when
CONFIG_IMX_WATCHDOG is defined.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Disable the warm reset and enable the cold reset for a more reliable
restart ('reset'). This is taken from the Linux kernel, see imx_src_init()
in arch/arm/mach-imx/src.c.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Replace "mmc open/close" with "mmc dev" in mx6sabre_common.h as those commands
were removed with this commit: 614b2bf1c9
cmd_mmc.c: Drop open/close mmc sub-commands
Signed-off-by: Maxin B. John <maxin.john@enea.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Provide instructions on how to upgrade U-boot in the eMMC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Device Firmware Upgrade (DFU) is a very convenient mechanism to upgrade U-boot
on the eMMC.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
