When converting test/py from " to ', I missed a few places (or added a
few inconsistencies later). Fix these.
Note that only quotes in code are converted; double-quotes in comments
and HTML are left as-is, since English and HTML use " not '.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Python's coding style docs indicate to use " not ' for docstrings.
test/py has other violations of the coding style docs, since the docs
specify a stranger style than I would expect, but nobody has complained
about those yet:-)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The existing net test executes a list of commands supplied by boardenv
variable env__net_pre_commands. The idea was that boardenv would know
whether the Ethernet device was attached to USB, PCI, ... and hence was
the best place to put any commands required to probe the device.
However, this approach doesn't scale well when attempting to use a single
boardenv across multiple branches of U-Boot, some of which require "pci
enum" to enumerate PCI and others of which don't, or don't /yet/ simply
because various upstream changes haven't been merged down.
This patch updates the test to require that the boardenv state which HW
features are required for Ethernet to work, and lets the test itself map
that knowledge to the set of commands to execute. Since this mapping is
part of the test script, which is part of the U-Boot code/branch, this
approach is more scalable. It also feels cleaner, since again boardenv
is only providing data, rather than test logic.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The DFU test requests U-Boot configure its USB controller in device mode,
then waits for the host machine to enumerate the USB device and create a
device node for it. However, this wait can be fooled if the USB device
node already exists before the test starts, e.g. if some previous software
stack already configured the USB controller into device mode and never
de-configured it. This "previous software stack" could even be another
test/py test, if U-Boot's own USB teardown does not operate correctly. If
this happens, dfu-util may be run before U-Boot is ready to serve DFU
commands, which may cause false test failures.
Enhance the dfu test to fail if the device node exists before it is
expected to.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
test/py contains logic to detect the target crashing and rebooting by
searching the console output for a U-Boot signon message, which will
presumably be emitted when the system boots after the crash/reset.
Currently, this logic only searches for the exact signon message that
was printed by the U-Boot version under test, upon the assumption that
binary is written into flash, and hence will be the version booted after
any reset. However, this is not a valid assumption; some test setups
download the U-Boot-under-test into RAM and boot it from there, and in
such a scenario an arbitrary U-Boot version may be located in flash and
hence run after any reset.
Fix the reset detection logic to match any U-Boot signon message. This
prevents false negatives.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
find_ram_base() is a shared utility function, not a core part of the
U-Boot console interaction.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a test of DFU functionality to the Python test suite. The test
starts DFU in U-Boot, waits for USB device enumeration on the host,
executes dfu-util multiple times to test various transfer sizes, many
of which trigger USB driver edge cases, and finally aborts the DFU
command in U-Boot.
This test mirrors the functionality previously available via the shell
scripts in test/dfu, and hence those are removed too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enhance the UMS test to optionally mount a partition and read/write a file
to it, validating that the content written and read back are identical.
This enhancement is backwards-compatible; old boardenv contents that don't
define the new configuration data will cause the test code to perform as
before.
test/ums/ is deleted since the Python test now performs the same testing
that it did.
The code is also re-written to make use of the recently added utility
module, and split it up into nested functions so the overall logic of
the test process can be followed more easily without the details
cluttering the code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add various common utility functions. These will be used by a forthcoming
re-written UMS test, and a brand-new DFU test.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Sometimes it's useful to run shell commands and ignore any errors. One
example might be cleanup logic; if a test-case experiences an error, the
cleanup logic might experience an error too, and we don't want that error
to mask the original error, so we want to ignore the subsequent error.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Write a note to the log file when a test sends CTRL-C to U-Boot. This
makes it easier to follow what's happening in the logs, especially since
U-Boot doesn't echo the character back to its output, so there's no other
signal of what's going on.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tests may fail for a number of reasons, and in particular for reasons
other than a timeout waiting for U-Boot to print expected data. If the
last operation that a failed test performs is not waiting for U-Boot to
print something, then any trailing output from U-Boot during that test's
operation will not be logged as part of that test, but rather either
along with the next test, or even thrown away, potentiall hiding clues
re: the test failure reason.
Solve this by explicitly draining (and hence logging) the U-Boot output
in the case of failed tests.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Prior to this change, U-Boot was lazilly (re-)spawned if/when a test
attempted to interact with it, and no active connection existed. This
approach was simple, yet had the disadvantage that U-Boot might be
spawned in the middle of a test function, e.g. after the test had already
performed actions such as creating data files, etc. In that case, this
could cause the log to contain the sequence (1) some test logs, (2)
U-Boot's boot process, (3) the rest of that test's logs. This isn't
optimally readable. This issue will affect the upcoming DFU and enhanced
UMS tests.
This change converts u_boot_console to be a function-scoped fixture, so
that pytest attempts to re-create the object for each test invocation.
This allows the fixture factory function to ensure that U-Boot is spawned
prior to every test. In practice, the same object is returned each time
so there is essentially no additional overhead due to this change.
This allows us to remove:
- The explicit ensure_spawned() call from test_sleep, since the core now
ensures that the spawn happens before the test code is executed.
- The laxy calls to ensure_spawned() in the u_boot_console_*
implementations.
The one downside is that test_env's "state_ttest_env" fixture must be
converted to a function-scoped fixture too, since a module-scoped fixture
cannot use a function-scoped fixture. To avoid overhead, we use the same
trick of returning the same object each time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently, Spawn.expect() imposes its timeout solely upon receipt of new
data, not on its overall operation. In theory, this could cause the
timeout not to fire if U-Boot continually generated output that did not
match the expected patterns.
Fix the code to additionally impose a timeout on overall operation, which
is the intended mode of operation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
We have a way to find a regmap by its syscon driver data value. Add the same
for syscon itself.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a test for the 'bmp' command. Test both the uncompressed and compressed
versions of the file, since they use different code paths.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Test that text is displayed correctly when the console is rotated.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add tests that check that the video console is working correcty. Also check
that text output produces the expected result. Test coverage includes
character output, wrapping and scrolling.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Execute "sleep", and validate that it sleeps for approximately the correct
amount of time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This test invokes the "ums" command in U-Boot, and validates that a USB
storage device is enumerated on the test host system, and can be read
from.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Migrate all most tests from command_ut.c into the Python test system.
This allows the tests to be run against any U-Boot binary that supports
the if command (i.e. where hush is enabled) without requiring that
binary to be permanently bloated with the code from command_ut.
Some tests in command_ut.c can only be executed from C code, since they
test internal (more unit-level) features of various U-Boot APIs. The
migrated tests can all operate directly from the U-Boot console.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This tests whether the following features of the U-Boot shell:
- Execution of a directly entered command.
- Compound commands (; delimiter).
- Quoting of arguments containing spaces.
- Executing commands from environment variables.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This tests whether md/mw work, and affect each-other.
Command repeat is also tested.
test/cmd_repeat.sh is removed, since the new Python-based test does
everything it used to.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This tests basic environment variable functionality.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Test the sandbox port's implementation of the reset command and SIGHUP
handling. These should both cause the U-Boot process to exit gracefully.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This tool aims to test U-Boot by executing U-Boot shell commands using the
console interface. A single top-level script exists to execute or attach
to the U-Boot console, run the entire script of tests against it, and
summarize the results. Advantages of this approach are:
- Testing is performed in the same way a user or script would interact
with U-Boot; there can be no disconnect.
- There is no need to write or embed test-related code into U-Boot itself.
It is asserted that writing test-related code in Python is simpler and
more flexible that writing it all in C.
- It is reasonably simple to interact with U-Boot in this way.
A few simple tests are provided as examples. Soon, we should convert as
many as possible of the other tests in test/* and test/cmd_ut.c too.
The hook scripts, relay control utilities, and udev rules I use for my
own HW setup are published at https://github.com/swarren/uboot-test-hooks.
See README.md for more details!
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org> #v3
- Use "mkdir -p" to avoid errors when intermediate directories are
missing.
- Fall back to "dd" when "fallocate" fails. For example, fallocate isn't
supported on ext4.
- Add error checking for test image generation. Without this, the test
simply plows on spewing all kinds of errors which are hard to
immediately root-cause.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Due to a limitation removed in an earlier patch, USB tests were not seeing
all the devices. Update the tests to pass now that all devices are visible.
Signed-off-by: Simon Glass <sjg@chromium.org>
This subsystem has been broken since commit:
4efad20a sf: Update status reg check in spi_flash_cmd_wait_ready
There has so far been no response from the maintainer, and a release is
imminent. For now, let's just disable the tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we may compile (but not link) code calling fixup_cmdtable when
this is not set, we need to always have the declaration available. We
should also make sure that anyone calling the function includes
<command.h> as that's where the function declaration is.
Signed-off-by: Tom Rini <trini@konsulko.com>
Subcommands contain pointers to functions which are not updated when
MANUAL_RELOC is enabled. This patch fix it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test that verifies that USB keyboards work correctly on sandbox.
This verifies some additional parts of the USB stack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add tests that this command produces the right output, even when a rescan
results in a device disappearing from the bus.
Signed-off-by: Simon Glass <sjg@chromium.org>
When running sandbox tests, silence the console to avoid unwanted output.
Also, record the console in case tests want to check it.
The -v option can be used to enable stdout during tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently the USB tests take around two seconds to run. Remove these
unnecessary time delays so that the tests run quickly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a sandbox timer which get time from host os and a basic
test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
Check the result code of all command that are executed. Without this,
if the fallocate invocation fails (this feature is not supported on ext3
filesystems for example) then a zero-length output file will be created,
and subsequent the mkfs and mount invocations will fail, which will cause
the subsequent dd invocation to attempt to fill up the host's entire free
disk space. That's not a nice user experience!
Related, if fallocate does fail, try to create the test disk image using
dd instead. That should work everywhere.
Fixes: 4a28274227 ("test: fat: add test of non-contiguous file reads")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
U-Boot crashes when doing a 'ping' with the following test scenario:
- All ethernet devices are not probed
- "ethaddr" for all ethernet devices are not set
- "ethact" is set to a valid ethernet device name
Add a new test case 'dm_test_eth_act' to hit such scenario.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In the following snippet:
if [ ! -x `which $prereq` ]; then
When $prereq does not exist, `which $prereq` evaluates to the empty string,
which results in *no* argument being passed to the -x operator, which then
evaluates to true, which is the equivalent of the prereq having been found. In
order for this to fail as expected, we must pass an empty argument, which then
causes -x to fail. Do this by wrapping the `` in quotes so there's always an
argument to -x, even if the value of the argument is zero-length.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
In my patch series to replace fs/fat with "ff.c", I enhanced ff.c to
optimize file reading, so that reads of contiguous clusters are submitted
to the IO device as a single read. This test attempts to torture-test
edge-cases of that enhancement.
BTW, the only way I found to validate that this script actually does
create non-contiguous files was to manually inspect the FAT bitmap in a
hex dump of the FAT image. hdparm --fibmap doesn't work on loop-mounted
filesystems. filefrag -v -e seems to lie about files being contiguous
when they aren't.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The current name is inconsistent with other driver model data access
functions. Rename it and fix up all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Use the sandbox environment for the basic tests.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
With the changes in 7a3e70c we now get read(2) behavior so trying to
read 2MB with 1MB left in the file results in 1MB read and a warning.
We update the test logic here to make sure we read back 1MB as expected.
This change however changes the overall summary as while EXT4 continues
to not have offset support the test now fails when expected to pass
rather than fails when expected to fail (and we report that as pass).
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds support for LZ4-compressed FIT image contents. This
algorithm has a slightly worse compression ration than LZO while being
nearly twice as fast to decompress. When loading images from a fast
storage medium this usually results in a boot time win.
Sandbox-tested only since I don't have a U-Boot development system set
up right now. The code was imported unchanged from coreboot where it's
proven to work, though. I'm mostly interested in getting this recognized
by mkImage for use in a downstream project.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Adjust the memory leak tests to show the amount of memory leaked. This can
be a useful signal as to what is wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add one more ethernet device node in the sandbox test device tree,
with name 'sbe5'. This is to support a new test case for testing
network device rotation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
dfu-util allows filtering on USB device vendor:product ID by using
the -d flag (-d 0451:d022).
Such option is very handy when many DFU devices are connected to a single
host PC. This commit allows testing when above situation emerges.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Lukasz Majewski <l.majewski@majess.pl>
Test HW - AM335x Beagle Bone Black
NOTE: Max size of file to transfer: 2MiB
- Re-direct stderr into the log files, so any errors U-Boot emits are
visible in the logs. This is relevant if the "reset" shell command
attempts to report that it's not supported on the sandbox board.
- Fix test_fs_nonfs() to name the files it created differently for each
invocation. Otherwise, the logs from different tests overwrite
each-other.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Suriyan Ramasami <suriyan.r@gmail.com>
This new command can dump all device resources associated to
each device. The fields in every line shows:
- The address of the resource
- The size of the resource
- The name of the release function
- The stage in which the resource has been acquired (BIND/PROBE)
Currently, there is no driver using devres, but if such drivers are
implemented, the output of this command should look like this:
=> dm devres
- root_driver
- soc
- extbus
- serial@54006800
bfb541e8 (8 byte) devm_kmalloc_release BIND
bfb54440 (4 byte) devm_kmalloc_release PROBE
bfb54460 (4 byte) devm_kmalloc_release PROBE
- serial@54006900
bfb54270 (8 byte) devm_kmalloc_release BIND
- gpio@55000000
- i2c@58780000
bfb5bce8 (12 byte) devm_kmalloc_release PROBE
bfb5bd10 (4 byte) devm_kmalloc_release PROBE
- eeprom
bfb54418 (12 byte) devm_kmalloc_release BIND
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a test to confirm that we can probe this device. Since there is no
MMC stack support in sandbox at present, this is as far as the test goes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add tests that confirm that the drivers work as expected, and we can walk
through the available reset types trying to reset the board.
Signed-off-by: Simon Glass <sjg@chromium.org>
All driver model tests have a dm_test_ prefix. Ignore it when matching a
test name. This makes it easier to run individual tests, like this:
./sandbox/u-boot -d ./sandbox/arch/sandbox/dts/test.dtb \
-c "ut dm clk_periph"
We can use 'clk_periph' instead of 'dm_test_clk_periph'.
Also print a message if the requested test is not found.
Signed-off-by: Simon Glass <sjg@chromium.org>
The regulator_autoset() function mixes printf() output and PMIC adjustment
code. It provides a boolean to control the output. It is better to avoid
missing logic and output, and this permits a smaller SPL code size. So
split the output into a separate function.
Also rename the function to have a by_name() suffix, since we would like
to be able to pass a device when we know it, and thus avoid the name
search.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
In SPL it is sometimes useful to be able to obtain a dump of the current
driver model state. Since commands are not available, provide a way to
directly call the functions to output this information.
Adjust the existing commands to use these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 9cc36a2 'dm: core: Add a flag to control sequence numbering' changed
the default uclass behaviour to not support bus numbering. This is incorrect
for PCI and that commit should have enabled the flag for PCI.
Enable it so that PCI buses can be found and the 'pci' command works again.
Also add a test for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Nothing too fancy. A simple test that attmpts to load two loadables and
verify that they are properly unpacked in the u-boot sandbox.
Signed-off-by: Karl Apsite <Karl.Apsite@dornerworks.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The behavior of the env attrs depends on CONFIG_REGEX. Add an additional
test if that variable is set.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new "env" subcommand to the ut command.
This will run unit tests on the env code. This should be targetable to
any device that supports the env features needed for the tests.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Put the driver model for the system back into a good state after
completing the DM testing.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
There's not much point in having a failure count if we always give up on
the first failure. Also stop clearing the entire state between tests.
Make sure that any failures are still passed out to the command line.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make all unit tests selectable as a menu of test suites instead of just
sitting in the top-level menu individually.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify the command for running unit tests further by moving the "ut_time"
command over to "ut time".
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Unify the command for running unit tests further by moving the "dm test"
command over to "ut dm".
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a command that all other unit tests should be a sub-command of.
Also include a command that will run all tests.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Separate the ability to define tests and assert status of test functions
from the dm tests so they can be used more consistently throughout all
tests.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use a regular expression to apply the default formatting flags for all
ethaddr env vars.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The file test.dts from driver model test directory,
was compiled by call dtc in script: test/dm/test-dm.sh.
This doesn't allow for including of dtsi files and using
of C preprocessor routines in this dts file.
Since the mentioned script builds U-Boot before tests,
then moving the test.dts file into sandbox dts directory
is reasonable.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
This change adds new file to sandbox driver model test environment.
The file is: test/dm/power.c, and it includes tests for PMIC framework,
which includes PMIC uclass and REGULATOR uclass.
All tests are based od Sandbox PMIC emulated device. Some test constants for
this device are defined in the header: include/power/sandbox_pmic.h
PMIC tests includes:
- pmic get - tests, that pmic_get() returns the requested device
- pmic I/O - tests I/O by writing and reading some values to PMIC's registers
and then compares, that the write/read values are equal.
The regulator tests includes:
- Regulator get by devname/platname
- Voltage set/get
- Current set/get
- Enable set/get
- Mode set/get
- Autoset
- List autoset
For the regulator 'get' test, the returned device pointers are compared,
and their names are also compared to the requested one.
Every other test, first sets the given attribute and next try to get it.
The test pass, when the set/get values are equal.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
Sometimes the time functions are incorrect due to bad time support on a
board. Add a unit test which tries to detect this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sort these aliases to avoid confusion as to what is present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
At present this driver has a few test features. They are needed for running
the driver model unit tests but are confusing and unnecessary if using
sandbox at the command line. Add a flag to enable the test mode, and don't
enable it by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Indicate to the emulated sandbox Ethernet driver when we expect a
timeout and tell it to leap forward.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
We must not clear global_data even in tests, since the ram_buffer (which
is used by malloc()) will also be lost, and subsequent tests will fail.
Zero only the global_data fields that are required for the test to function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Joe Hershberger <joe.hershberger@ni.com>
This commit introduces simple tests for functions:
- uclass_find_device_by_name()
- uclass_get_device_by_name()
Tests added by this commit:
- Test: dm_test_uclass_devices_find_by_name: for uclass id: UCLASS_TEST_FDT
* get uclass's devices by uclass_find_first/next_device() each as 'testdev',
* for each returned device, call: uclass_find_device_by_name(),
with previously returned device's name as an argument ('testdev->name').
* for the found device ('founddev') check if:
* founddev != NULL
* testdev == founddev
* testdev->name == founddev->name (by strcmp)
- Test: dm_test_uclass_devices_get_by_name: for uclass id: UCLASS_TEST_FDT
* get uclass's devices by uclass_get_first/next_device() each as 'testdev',
* for each returned device, call: uclass_get_device_by_name(),
with previously returned device's name as an argument ('testdev->name').
* for the found device ('founddev') check if:
* founddev != NULL
* founddev is active
* testdev == founddev
* testdev->name == founddev->name (by strcmp)
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit introduces simple tests for functions:
- uclass_find_first_device()
- uclass_find_next_device()
- uclass_first_device()
- uclass_next_device()
Tests added by this commit:
- Test: dm_test_uclass_devices_find:
* call uclass_find_first_device(), then check if: (dev != NULL), (ret == 0)
* for the rest devices, call uclass_find_next_device() and do the same check
- Test: dm_test_uclass_devices_get:
* call uclass_first_device(), then check if:
-- (dev != NULL), (ret == 0), device_active()
* for the rest devices, call uclass_next_device() and do the same check
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This test introduces new test structure type:dm_test_perdev_uc_pdata.
The structure consists of three int values only. For the test purposes,
three pattern values are defined by enum, starting with TEST_UC_PDATA_INTVAL1.
This commit adds two test cases for uclass platform data:
- Test: dm_test_autobind_uclass_pdata_alloc - this tests if:
* uclass driver sets: .per_device_platdata_auto_alloc_size field
* the devices's: dev->uclass_platdata is non-NULL
- Test: dm_test_autobind_uclass_pdata_valid - this tests:
* if the devices's: dev->uclass_platdata is non-NULL
* the structure of type 'dm_test_perdev_uc_pdata' allocated at address
pointed by dev->uclass_platdata. Each structure field, should be equal
to proper pattern data, starting from .intval1 == TEST_UC_PDATA_INTVAL1.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Finish eliminating CamelCase from net.c and other failures
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch is simply clean-up to make the IPv4 type that is used match
what Linux uses. It also attempts to move all variables that are IP
addresses use good naming instead of CamelCase. No functional change.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds a simple test for probing and a functional test using the flash
stick emulator, which tests a large chunk of the USB stack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
As well as running all tests, it is useful to be able to run a selected test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The uclass pre-probe functions may end up calling back into the device in
some circumstances. This can fail if recursion takes place. Adjust the
ordering so that we mark the device as active early, then retract this
later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Take a pass at plumbing errors through to the users of the network stack
Currently only the start() function errors will be returned from
NetLoop(). recv() tends not to have errors, so that is likely not worth
adding. send() certainly can return errors, but this patch does not
attempt to plumb them yet. halt() is not expected to error.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The effect of the "netretry" env var was recently changed. This test
checks that behavior.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure that the ethrotate behavior occurs as expected.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ethprime env var is used to indicate the starting device if none is
specified in ethact. Also support aliases specified in the ethprime var.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow network devices to be referred to as "eth0" instead of
"eth@12345678" when specified in ethact.
Add tests to verify this behavior.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test for the eth uclass using the sandbox eth driver. Verify basic
functionality of the network stack / eth uclass by exercising the ping
function.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the case where the arch defines a custom map_sysmem(), make sure that
including just mapmem.h is sufficient to have these functions as they
are when the arch does not override it.
Also split the non-arch specific functions out of common.h
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Both of these values are useful for understanding what is going on, so show
them both.
The requested number comes from a device tree alias. The allocated one is
set up when the device is activated, and is unique throughout the uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some uclasses want to set up a device before it is probed. Add a method
for this.
An example is with PCI, where a PCI uclass wants to set up its private
data for later use. This allows the device's uclass() method to make calls
whcih use that data (for example, read PCI memory regions from device
tree, set up bus numbers).
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a convenience function to access the private data that a uclass stores
for each of its devices. Convert over most existing uses for consistency
and to provide an example for others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a file to control driver model test features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
As with i2c_read() and i2c_write(), add a dm_ prefix to the driver model
versions of these functions to avoid conflicts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
At present we go through various contortions to store the SPI slave's chip
select in its private data. This only exists when the slave is active so
must be set up when it is probed. Until the device is probed we don't
actually know what chip select it will appear on.
However, now that we can support per-child platform data, we can use that
instead. This allows us to set up the chip select when the child is bound,
and avoid the messy contortions.
Unfortunately this is a fairly large change and it seems to be difficult to
break it down further.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some buses need to set up their devices before they can be used. This setup
may well be common to all buses in a particular uclass. Support a common
pre-probe method for the uclass, called before any bus devices are probed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
For buses, after a child is bound, allow the uclass to perform some
processing. This can be used to figure out the address of the child (e.g.
the chip select for SPI slaves) so that it is ready to be probed.
This avoids bus drivers having to repeat the same process, which really
should be done by the uclass, since it is common.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
In many cases the per-child private data for a device's children is defined
by the uclass rather than the individual driver. For example, a SPI bus
needs to store information about each of its children, but all SPI drivers
store the same information. It makes sense to allow the uclass to define
this data.
If the driver provides a size value for its per-child private data, then use
it. Failng that, fall back to that provided by the uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
At present we try to use the 'reg' property and device tree aliases to give
devices a sequence number. The 'reg' property is often actually a memory
address, so the sequence numbers thus-obtained are not useful. It would be
better if the devices were just sequentially numbered in that case. In fact
neither I2C nor SPI use this feature, so drop it.
Some devices need us to look up an alias to number them within the uclass.
Add a flag to control this, so it is not done unless it is needed.
Adjust the tests to test this new behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This is useful to check which uclass a device is in.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Allow parent drivers to be called when a new child is bound to them. This
allows a bus to set up information it needs for that child.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
In many cases the child platform data for a device's children is defined by
the uclass rather than the individual devices. For example, a SPI bus needs
to know the chip select and speed for each of its children. It makes sense
to allow this information to be defined the SPI uclass rather than each
individual driver.
If the device provides a size value for its child platdata, then use it.
Failng that, fall back to that provided by the uclass.
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
For buses it is common for parents to need to know the address of the child
on the bus, the bus speed to use for that child, and other information. This
can be provided in platform data attached to each child.
Add driver model support for this, including auto-allocation which can be
requested using a new property to specify the size of the data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
When using allocated platform data, allocate it when we bind the device.
This makes it possible to fill in this information before the device is
probed.
This fits with the platform data model (when not using device tree),
since platform data exists at bind-time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Rather than assuming that the chip offset length is 1, allow it to be
provided. This allows chips that don't use the default offset length to
be used (at present they are only supported by the command line 'i2c'
command which sets the offset length explicitly).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Add a dm_ prefix to driver model I2C functions so that we can keep the old
ones around.
This is a little unfortunate, but on reflection it is too difficult to
change the API. We can undo this rename when most boards and drivers are
converted to use driver model for I2C.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present U-Boot sort-of supports the standard way of reading GPIOs from
device tree nodes, but the support is incomplete, a bit clunky and only
works for GPIO bindings where #gpio-cells is 2.
Add new functions to request GPIOs, taking full account of the device
tree binding. These permit requesting a GPIO with a simple call like:
gpio_request_by_name(dev, "cd-gpios", 0, &desc, GPIOD_IS_IN);
This will request the GPIO, looking at the device's node which might be
this, for example:
cd-gpios = <&gpio TEGRA_GPIO(B, 3) GPIO_ACTIVE_LOW>;
The GPIO will be set to input mode in this case and polarity will be
honoured by the GPIO calls.
It is also possible to request and free a list of GPIOs.
Signed-off-by: Simon Glass <sjg@chromium.org>
The dumpimage is able to extract components contained in a FIT image:
$ ./dumpimage -T flat_dt -i CONTAINER.ITB -p INDEX FILE
The CONTAINER.ITB is a regular FIT container file. The INDEX is the poisition
of the sub-image to be retrieved, and FILE is the file (path+name) to save the
extracted sub-image.
For example, given the following kernel.its to build a kernel.itb:
/dts-v1/;
/ {
...
images {
kernel@1 {
description = "Kernel 2.6.32-34";
data = /incbin/("/boot/vmlinuz-2.6.32-34-generic");
type = "kernel";
arch = "ppc";
os = "linux";
compression = "gzip";
load = <00000000>;
entry = <00000000>;
hash@1 {
algo = "md5";
};
};
...
};
...
};
The dumpimage can extract the 'kernel@1' node through the following command:
$ ./dumpimage -T flat_dt -i kernel.itb -p 0 kernel
Extracted:
Image 0 (kernel@1)
Description: Kernel 2.6.32-34
Created: Wed Oct 22 15:50:26 2014
Type: Kernel Image
Compression: gzip compressed
Data Size: 4040128 Bytes = 3945.44 kB = 3.85 MB
Architecture: PowerPC
OS: Linux
Load Address: 0x00000000
Entry Point: 0x00000000
Hash algo: md5
Hash value: 22352ad39bdc03e2e50f9cc28c1c3652
Which results in the file 'kernel' being exactly the same as '/boot/vmlinuz-2.6.32-34-generic'.
Signed-off-by: Guilherme Maciel Ferreira <guilherme.maciel.ferreira@gmail.com>
Some image types, like "KeyStone GP", do not have magic numbers to
distinguish them from other image types. Thus, the automatic image
type discovery does not work correctly.
This patch also fix some integer type mismatches.
Signed-off-by: Guilherme Maciel Ferreira <guilherme.maciel.ferreira@gmail.com>
Use each compression method (including uncompressed). Test for normal
operation, insufficient space and corrupted data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Prior to commit d455d87 there was an inconsistency between the position of
the 'address' parameter in 'sb load' and 'sb save'. This was corrected but
it broke some tests. Fix the tests and also the help for 'sb save'.
Signed-off-by: Simon Glass <sjg@chromium.org>
This change helps to run script on machines with quite long uptime.
Without this the following error emerges:
File: ./dat_14M.img
umount: /mnt/tmp-ums-test: device is busy.
(In some cases useful info about processes that use
the device is found by lsof(8) or fuser(1))
TX: md5sum:083d3d22b542d3ecba61b12d17e03f9f
mount: /dev/sdd6 already mounted or /mnt/tmp-ums-test busy
mount: according to mtab, /dev/sdd6 is already mounted on /mnt/tmp-ums-test
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
run_command() returns success even if the command had a syntax error;
correct this behaviour.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Simon Glass <sjg@chromium.org)
Attempting to run:
- an empty string
- a string with just spaces
returns different error codes, 1 for the empty string and 0
for the string with just spaces. Make both of them return
0 for consistency.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Simon Glass <sjg@chromium.org)
These types are problematic because they are typically declared in a
non-standard way in U-Boot. For example, U-Boot uses 'long long' for
int64_t even on a 64-bit machine whereas stdint.h uses 'long'.
Similarly, U-Boot always uses 'long' for intptr_t whereas stdint.h mostly
uses 'int'.
This simple test script runs a few toolchains on a few archs to check for
warnings.
Signed-off-by: Simon Glass <sjg@chromium.org>
The run command treats each argument an an environment variable. It gets the
value of each variable and executes it as a command. If an environment
variable contains a newline and the hush cli is used, it is supposed to
execute each line one after the other.
Normally a newline signals to hush to exit - this is used in normal command
line entry - after a command is entered we want to return to allow the user
to enter the next one. But environment variables obviously need to execute
to completion.
Add a special case for the execution of environment variables which
continues when a newline is seen, and add a few tests to check this
behaviour.
Note: it's not impossible that this may cause regressions in other areas.
I can't think of a case but with any change of behaviour with limited test
coverage there is always a risk. From what I can tell this behaviour has
been around since at least U-Boot 2011.03, although this pre-dates sandbox
and I have not tested it on real hardware.
Reported-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Check the state of the malloc() heap before each test is run, so that tests
can verify that all is well at the end. Provide helper functions to mark
the heap and to check that it returns to its initial state.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple test for SPI that uses SPI flash. It operates by creating a
SPI flash file and using the 'sf test' command to test that all
operations work correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
These tests use SPI flash (and the sandbox emulation) to operate.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
