Add function to read SD_STATUS information.
According to the information, get erase_timeout/erase_size/erase_offset.
Add a structure sd_ssr to include the erase related information.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Stephen Warren <swarren@nvidia.com>
No need for per-SoC adjustment for this parameter. It should be
determined by the slowest hardware. Currently, no board overrides
this CONFIG, so 3.2 sec is large enough. (If not, we can make it
even larger.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This CONFIG is not configurable since it is not guarded by #ifndef.
Nobody has complained about that, so there is no need to keep it as
a CONFIG option.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_BLK is enabled, add_sdhci() is never called. Move this
quirk handling to sdhci_setup_cfg(), which is now the central place
for hardware capability checks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_BLK is enabled, add_sdhci() is never called. Move this
quirk handling to sdhci_setup_cfg(), which is now the central place
for hardware capability checks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
"Hardware doesn't specify base clock frequency" may not be only the
error case of sdhci_setup_cfg(). It is better to print this where
the corresponding error is triggered.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_BLK is enabled, add_sdhci() is never called.
So, sdhci_reset() is not called, either. This is a problem for
my board as it needs the reset to start from a sane state.
Move the add_sdhci() call to sdhci_init(), which is visited
by both of the with/without CONFIG_BLK cases.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit 90c08d9e08.
I took a closer look at this after the commit was applied, and found
CONFIG_SYS_MALLOC_F_LEN=0x2000 was too much. 8KB memory for SPL is
actually too big for some boards. Perhaps 0x800 is enough, but the
situation varies board by board.
Let's postpone our decision until we come up with a better idea.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Import the latest version from the Diag software.
- Support LD21 SoC (including DDR chips in the package)
- Per-board granule adjustment for both reference and TV boards
- Misc cleanups
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Initialize the DPLL (PLL for DRAM) in SPL, and others in U-Boot
proper. Split the common code into pll-base-ld20.c for easier
re-use.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now PLLs for DRAM controller are initialized in SPL, and the others
in U-Boot proper. Setting up all of them in a single directory will
be helpful when we want to share code between SPL and U-Boot proper.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The PLL for the DRAM interface must be initialized in SPL, but the
others can be delayed until U-Boot proper. Move them from SPL to
U-Boot proper to save the precious SPL memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is the last code in the mach-uniphier/pinctrl/ directory.
Push the remaining code out to delete the directory entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the pin-mux data in the pinctrl drivers by directly calling
pinctrl_generic_set_state().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This will be needed for setting up the System Bus pin-mux via the
LD11/LD20 pinctrl driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The NAND subsystem has not supported the Driver Model yet, but the
NAND pin-mux data are already in the pinctrl drivers. Use them by
calling pinctrl_generic_set_state() directly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now all UniPhier SoCs support a pinctrl driver. Select (SPL_)PINCTRL
since it is mandatory even for base use.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
On LD4 SoC or later, the pin-mux registers are 8bit wide, while 4bit
wide on sLD3 SoC. Support it for the sLD3 pinctrl driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Sinlinx SinA33 has a USB OTG port, but VBUS is controlled manually from
a jumper pad.
Enable OTG in gadget mode, as well as the download gadget and related
functions.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Sinlinx SinA33 has 1 USB host port. Enable EHCI_HCD support for it.
Also enable USB mass storage support so we can access USB sticks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Sinlinx SinA33 uses PB4 for mmc0 card detect.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The NanoPi NEO is a simple h3 board with 512MB RAM, ethernet, one usb
and one usb OTG connector.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
With sunxi-musb musb_lowlevel_init() can fail when a charger; or no cable
is plugged into the otg port.
To avoid leaking the struct musb allocated by musb_init_controller()
on repeated musb_usb_probe() calls, we were caching its result.
But musb_init_controller() does more, such as calling sunxi_musb_init()
which enables the clocks.
Not calling sunxi_musb_init() causes the musb controller to stop working
after a "usb reset" since that calls musb_usb_remove() which disables the
clocks.
This commit fixes this by removing the caching of the struct returned
from musb_init_controller(), it replaces this by free-ing the allocated
memory in musb_usb_remove() and calling musb_usb_remove() on
musb_usb_probe() errors to ensure proper cleanup.
While at it also make musb_usb_probe() and musb_usb_remove() static.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Linux kernel musb driver expects VBUS to be off while initializing
musb. Having it on results in a repeating string of warnings, followed
by an unusable peripheral. The peripheral is only usable after
physically removing the OTG adapter, letting musb reset its state.
This partially reverts commit c9f8947e66 ("sunxi: usb-phy: Never
power off the usb ports")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When cold-booting the ldoio0/1 regulators are always off / the
gpios are always at tristate. But when re-booting from android these
are sometimes on. Disable them at axp_init time (iow as early as possible)
to remove this difference between a cold boot and a reboot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
New CONFIG options should be added via Kconfig. To help prevent new ad-hoc
CONFIGs from being added, give a build error when these are detected.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Add a list of ad-hoc CONFIG options that don't use Kconfig. This can be used
to check that new ones are not being added.
Signed-off-by: Simon Glass <sjg@chromium.org>
