Currently there are 3 different variants of read_id implementation:
1. opcode only. Found in GD5FxGQ4xF.
2. opcode + 1 addr byte. Found in GD5GxGQ4xA/E
3. opcode + 1 dummy byte. Found in other currently supported chips.
Original implementation was for variant 1 and let detect function
of chips with variant 2 and 3 to ignore the first byte. This isn't
robust:
1. For chips of variant 2, if SPI master doesn't keep MOSI low
during read, chip will get a random id offset, and the entire id
buffer will shift by that offset, causing detect failure.
2. For chips of variant 1, if it happens to get a devid that equals
to manufacture id of variant 2 or 3 chips, it'll get incorrectly
detected.
This patch reworks detect procedure to address problems above. New
logic do detection for all variants separatedly, in 1-2-3 order.
Since all current detect methods do exactly the same id matching
procedure, unify them into core.c and remove detect method from
manufacture_ops.
This is a rework of Chuanhong Guo <gch981213@gmail.com> patch
submitted to linux kernel
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/all/20230110115843.391630-1-frieder@fris.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Make that condition more generic by checking if the memory controller
driver is enabled instead of using the EVM's config.
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Update the MAINTAINERS file and propose a new MAINTAINER for j721s2 due
to the previous MAINTAINER not being associated with TI.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The following commit syncs the device tree from Linux tag
v6.6-rc1 to U-boot and fixes the following to be compatible with
the future syncs -
- Include k3-am68-sk-base-board.dts file
Remove the duplicated pinmuxes from r5 and -u-boot.dtsi files and
include k3-am68-sk-base-board.dts for Linux fixes to propagate
to U-boot.
- Fixing the mcu_timer0
Remove timer0 and use the mcu_timer0 defined in mcu-wakeup.dtsi
- Fixing secure proxy nodes
Linux DT now have these nodes defined so remove them and rename to
use the Linux DT ones.
- Remove cpsw node
The compatible is now fixed and the node is not required in
-u-boot specifically
- Remove aliases and chosen node
Use these from Linux and don't override when not required.
- Remove /delete-property/ from sdhci nodes
We have the necessary clock and dev data so remove these.
- Remove dummy_clocks and fs_loader0
These weren't being used anywhere so remove it.
- Remove mcu_ringacc override
All these have been put in a single commit to not break the
bisectability.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The following commit syncs the device tree from Linux tag
v6.6-rc1 to U-boot and fixes the following to be compatible with
the future syncs -
- Include k3-j721s2-common-proc-board.dts file
Remove the duplicated pinmuxes from r5 and -u-boot.dtsi files and
include k3-j721s2-common-proc-board.dts for Linux fixes to propagate
to U-boot.
- Fixing the mcu_timer0
Remove timer0 and use the mcu_timer0 defined in mcu-wakeup.dtsi
- Fixing secure proxy nodes
Linux DT now have these nodes defined so remove them and rename to
use the Linux DT ones.
- Remove cpsw node
The compatible is now fixed and the node is not required in
-u-boot specifically
- Remove aliases and chosen node
Use these from Linux and don't override when not required.
- Remove /delete-property/ from sdhci nodes
We have the necessary clock and dev data so remove these.
- Remove dummy_clocks and fs_loader0
These weren't being used anywhere so remove it.
- Remove mcu_ringacc override
All these have been put in a single commit to not break the
bisectability.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
mcu_timer0 is used by u-boot as the tick-timer. Add it to the soc
devices lsit so it an be enabled via the k3 power controller.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The update causes instability in am68-sk boards so revert the patch in
the meantime till fix is available.
This reverts commit f1edf4bb6a.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The malloc capacity in DRAM at R5 SPL is set to 1MB which isn't
sufficient to load the new tispl.bin to
enable loading of tispl.bin the size is increased by 256KB to 1.25MB.
Cc: Nikhil M Jain <n-jain1@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Sync j7200 dts with Linux 6.6-rc1
- k3-j7200-r5-common-proc-board.dts now inherits from
k3-j7200-common-proc-board.dts instead of k3-j7200-som-p0.dtsi. This
allows us to trim down the r5 file considerably by using existing
properties
- remove pimux nodes from r5 file
- remove duplicate nodes & node properties from r5/u-boot files
- mcu_timer0 now used instead of timer1
mcu_timer0 device id added to dev-data.c file in order to work
- remove cpsw node
This node is no longer required since the compatible is now fixed
- remove dummy_clock_19_2_mhz
This node wasn't being used anyhere, so it was removed
- remove dummy_clock_200mhz
main_sdhci0 & main_sdhci1 no longer need dummy clock for eMMC/SD
- fix secure proxy node
mcu_secproxy changed to used secure_prxy_mcu which is already
defined in k3-j7200-mcu-wakeup.dtsi
- removed &mcu_ringacc property override since they're present in
v6.6-rc1
Signed-off-by: Reid Tonking <reidt@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
mcu_timer0 is now used as the tick timer in u-boot, so this adds the
timer to the soc device list so it can be enabled via the k3 power
controller.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Reid Tonking <reidt@ti.com>
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Drop header files that are no longer needed in am64x_evm.h.
k3_dfu.h is available via k3_dfu.env in am64x.env.
Drop unused macro CFG_SYS_SDRAM_BASE1.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
ti_mmc is not a valid boot_target for standard boot flow so
remove it. Prefer mmc1 (sd-card) over mmc0 (emmc).
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
AVS driver needs to be notified before or after clock change,
depending upon new rate is greater or less than current clock rate.
Fixes: 1e0aa873bc7cd ("clk: clk-ti-sci: Notify AVS driver upon setting clock rate")
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
AVS is enabled at R5 SPL stage, on few platforms like J721E
and J7200 clk-k3 is used instead if clk-sci driver.
Add support in clk-k3 driver as well to notify AVS driver
on setting clock rate so that voltage is changed accordingly.
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
To quote the author:
So far expo only supports menus. These are quite flexible for various
kinds of settings, but cannot deal with free-form input, such as a
serial number or a machine name.
This series adds support for a textline object, which is a single line
of text. It has a maximum length and its value is stored within the expo
structure.
U-Boot already has a command-line editor which provides most of the
features needed by expo. But the code runs in its own loop and only
returns when the line is finished. This is not suitable for expo, which
must handle a keypress at a time, returning to its caller after each
one.
In order to use the CLI code, some significant refactoring is included
here. This mostly involves moving the internal loop of the CLI to a
separate function and recording its state in a struct, just as was done
for single keypresses some time back. A minor addition is support for
Ctrl-W to delete a word, since strangely this is currently only present
in the simple version.
The video-console system provides most of the features needed by
testline, but a few things are missing. This series provides:
- primitive cursor support so the user can see where he is typing
- saving and restoring of the text-entry context, so that expo can allow
the user to continue where he left off, including deleting previously
entered characters correctly (for Truetype)
- obtaining the nominal width of a string of n characters, so that a
suitable width can be chosen for the textline object
Note that no support is provided for clearing the cursor. This was
addressed in a previous series[1] which could perhaps be rebased. For
this implementation, the cursor is therefore not enabled for the normal
command line, only for expo.
Reading and writing textline objects is supported for FDT and
environment, but not for CMOS RAM, since it would likely use too much
RAM to store a string.
In terms of code size, the overall size increase is 180 bytes for
Thumb02 boards, 160 of whcih is the addition of Ctrl-W to delete a word.
[1] https://patchwork.ozlabs.org/project/uboot/list/?series=280178&state=*
ao-secure node can be used to get information about the board,
so, for example, using show_board_info() we can get following
information for board with Meson A1 SoC:
SoC: Amlogic Meson A1 (A113L) Revision 2c:a (1:a)
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Link: https://lore.kernel.org/r/20231010100623.74475-3-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Currently we have all drivers for use USB stack on A1-series
SoC's. Let's enable USB options for the Amlogic AD401 reference A1
SoC board.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-9-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
We use this clocks in dwc3 driver.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-7-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Setting G12A and A1 is similar, so we can use G12A phy
driver with little changes.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-6-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
It is better to use defines instead of write raw
hex values in regmap.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-4-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This patch adds reset support for the Amlogic A1 family.
We add the structure meson_reset_drvdata, which in the future
will allow this driver to be used for other families by declaring
only the correct parameters reg_count and level_offset.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-3-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This patch adds basic clock driver for Amlogic A1 Family which supports
enabling/disabling some gates, getting frequencies and setting rate
with limited reparenting.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230925155209.130671-3-ivprusov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add clock bindings for Amlogic A1 from linux-next next-20230821.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230925155209.130671-2-ivprusov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The boot option automatically created by efibootmgr is identified
by the special guid appended in the optional data of boot option.
The same mechanism is implemented in the EDK II reference
implementation, it uses the different guid from the one currently
U-Boot uses.
The guid indicating auto-created boot option is not defined in the
UEFI specification, but some userspace tools such as 'efivar' package
are aware of the guid used in EDK II as auto-created boot option.
So let's use the same guid as EDK II reference implementation.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The BitBlt test leaves the serial console output in disarray.
* Call ClearScreen() where needed.
* Test CheckEvent() for EFI_SIMPLE_TEXT_INPUT_PROTOCOL.WaitForKey
via adding navigation keys
* Correct timer comment
For testing on the sandbox:
CONFIG_CMD_BOOTEFI_SELFTEST=y
CONFIG_CONSOLE_TRUETYPE=n
$ ./u-boot -T -l
=> setenv efi_selftest block image transfer
=> bootefi selftest
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Some of the information in README.rmobile is obsolete, references
defconfigs which no longer exist in u-boot or has broken links. The
information which is still relevant is moved into the reStructuredText
documentation under `doc/board/renesas`, and `doc/README.rmobile` is
dropped.
The list of boards in `doc/board/renesas` is converted into a table so
it's easier to see which defconfig to use. The list is expanded based on
reviewing the current u-boot code and the contents of the eLinux wiki
[1] [2].
[1]: https://elinux.org/R-Car
[2]: https://elinux.org/RZ-G
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This video covers the basics in a short time, so add a link to it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Cyclic now just print a warning once instead of disabling the cyclic
function when the cyclic function upon exceeding CPU time usage.
Fixes: ddc8d36a74 ("cyclic: Don't disable cylic function upon exceeding CPU time")
Signed-off-by: Weizhao Ouyang <o451686892@gmail.com>
Rephrase the paragraph.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
While not a direct issue for us, urllib3 before 1.26.17 is vulnerable to
CVE-2023-43804 to bump our version up.
Reported-by: GitHub dependabot
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use urllib3 2.0.6
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add textline to the list of objects which tthe expo builder can build.
This allows them to be provided in the description.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present cedit only supports menu keys. For textline objects we need
to insert normal ASCII characters.
We also need to handle backspace, which is ASCII 9.
In fact, expo does not make use of all the menu keys, so partition
them accordingly and update the logic to support normal ASCII
characters, too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide an implementation for textlines in the scene code, so that they
are displayed correctly. Provide a way to have a border around the
textline, with the internal part being the same colour as the
background. This looks more natural.
Signed-off-by: Simon Glass <sjg@chromium.org>
This object needs special handling when it is opened, to set up the CLI
and the vidconsole context. Add special support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
A textline is a line of text which can be edited by the user. It has a
maximum length (in chracters) but otherwise there are no restrictions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the CLI state, a buffer to hold the old value of the text being
edited and a place to save vidconsole entry context. These will be use
by the textline object.
Set an upper limit on the maximum number of characters in a textline
object supported by expo, at least for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
So far only menus have a background. When other object types are
rendered, they may have a background too. Make this code more generic
so it will be usable by new object types.
Signed-off-by: Simon Glass <sjg@chromium.org>
When the devicetree is too small for the property being written, we need
to expand the devicetree and retry the write.
Put this logic into a function so it can be reused.
Signed-off-by: Simon Glass <sjg@chromium.org>
So far only menus can be highlighted. With the coming addition of
text lines we need to be able to highlight other objects. Add a function
to determine whether an object can be highlighted.
Signed-off-by: Simon Glass <sjg@chromium.org>
