During misc_init_r, make sure to setup the clocks
properly for the USB hub on the pandaboard. With
this in place, the USB hub and the ethernet works
on the pandaboard.
Signed-off-by: Chris Lalancette <clalancette@gmail.com>
Acked-by: Aneesh V <aneesh@ti.com>
Fix:
omap2420h4.c: In function 'dram_init':
omap2420h4.c:196:25: warning: variable 'cpu' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Tom Rini <trini@ti.com>
Fix:
flash.c: In function 'flash_get_offsets':
flash.c:122:10: warning: variable 'pOrgDef' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'flash_erase':
flash.c:263:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:439:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dave Peverley <dpeverley@mpc-data.co.uk>
Acked-by: Tom Rini <trini@ti.com>
Fix:
flash.c: In function 'flash_get_offsets':
flash.c:139:10: warning: variable 'pOrgDef' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'flash_erase':
flash.c:280:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:456:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Tom Rini <trini@ti.com>
The only change of note is that we move from 0x80008000 to 0x80100000
for CONFIG_SYS_TEXT_BASE
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Tested-by: Koen Kooi <k-kooi@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Add Hynix 200MHz timing information to <asm/arch-omap3/mem.h>.
This also changes CONFIG_SYS_TEXT_BASE to 0x80100000.
Signed-off-by: Tom Rini <trini@ti.com>
This introduces 200MHz Micron parts timing information based on x-loader
to <asm/arch-omap3/mem.h> and Numonyx MCFG calculation. The memory init
logic is also based on what x-loader does in these cases. Note that
while previously u-boot would be flashed in with SW ECC in this case it
now must be flashed with HW ECC. We also change CONFIG_SYS_TEXT_BASE to
0x80100000.
Cc: Dirk Behme <dirk.behme@gmail.com>
Beagleboard rev C5, xM rev A:
Tested-by: Tom Rini <trini@ti.com>
Beagleboard xM rev C:
Tested-by: Matt Ranostay <mranostay@gmail.com>
Beagleboard rev B7, C2, xM rev B:
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
TPS power IC is controlled using a GPIO (gpio_wk7).
This GPIO should be maintained at logic 1 always. As
such an internal pull-up on this pin will do the job,
driving the GPIO outuput is not needed. This will avoid
the need of using GPIO library in SPL and also may
save some power.
Signed-off-by: Aneesh V <aneesh@ti.com>
Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.
Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.
OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
It is now responsibility of the board specific init
code to set the environment variable corresponding
to the MAC address.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
gpio_free() should not have the side effect of setting the line to input since this prevents the gpio command from being able to set a line as output.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Not all padconfs are the same between 4430 and 4460, so instead of
working around this with an if, we should have an specific padconf
structure for both chips (like handling the differences between the LEDs
GPIOs and TPS).
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Result of running the following command to address Wolfgang's
comment about camel case:
for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done
Discussion:
http://patchwork.ozlabs.org/patch/84988/
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
omap4: fix pad configuration settings for SDP and Panda
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sebastien Jan <s-jan@ti.com>
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Read the led output state from GPIO instead saving state in memory when it is [re]set
* Added a toggle option to the led command
Previous discussion:
http://lists.denx.de/pipermail/u-boot/2011-May/093068.html
Changes since v1:
Fixed checkpatch errors
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fixed USR0/USR1 to be LED 0/1 respectively
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Based on patches from Syed Mohammed Khasim (khasim@ti.com).
Configures the output of the BeagleBoard DVI to be orange.
Configures the output of the BeagleBoard S-Video to be a colorbar.
Changed display_init to beagle_display_init as suggested by Igor Grinberg:
http://www.mail-archive.com/u-boot@lists.denx.de/msg51446.html
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Based on commit f1099c7c43caf5bac3bf6a65aa266fade4747072
Author: Greg Turner <gregturner@ti.com>
Date: Tue May 25 09:19:06 2010 -0500
New u-boot command for status of USER button on BeagleBoard-xM
Modified bootcmd to check the staus at boot time and set
filename of the boot script.
* Moved to a BeagleBoard specific file.
* Removed changes to default boot command from adding userbutton
command.
* Made to handle pre-xM boards.
* Flipped polarity of the return value to avoid confusion. Success (0)
is when the button is pressed. Failure (1) is when the button is NOT
pressed.
* Used latest revision getting function.
* Used latest macros for board revision.
* Added xM-C revision definition (optional, since it was default)
* updated default configuration with UserButton functionality
* Added a separate bootenv variable to load a user defined .txt file
* Added an example, showing how a different environment file can be loaded with
the user button pressed
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Greg Turner <gregturner@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This fixes display problems in linux
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The below patch reverses the order of two segments in the board file.
Output pins need to have their values initialized, before they are
exposed to the logic outside the chip.
Signed-off-by: Bob Feretich <bob.feretich@rafresearch.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy mmc driver to the
new generic mmc driver.
This patch is based on similar patch for beagle[1].
[1] http://git.denx.de/?p=u-boot.git;a=commitdiff_plain;h=0cd31144240
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Innovator and H2 boards used machine_is_* macros for setting the machine
type. These macros are expanded in compile time and thus leaves
unreachable code (though gcc might optimize it).
Switch them to use common code for machine type setting.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
- Provide alternate implementations of board_init_f()
board_init_r() for OMAP spl.
- Provide linker script
- Initialize global data
- Add serial console support
- Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move
it to board config header from config.mk
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- separate mux settings into essential and non essential parts
- essential part is board independent as of now(so move it
to SoC directory). Will help in having single SPL for all
boards.
- Non-essential part(the pins not essential for u-boot to function)
need to be phased out eventually.
- Correct mux data by aligning to the latest settings in x-loader
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
These functions are not required when CONFIG_CMD_NET
is not defined:
- setup_net_chip()
- reset_net_chip()
- board_eth_init()
This patch wraps them in #ifdef CONFIG_CMD_NET...#endif
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The GPIO pin used for resetting the external LAN chip has
changed for Rev.G board.
The patch uses generic gpio API instead of direct access
to corresponding registers.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In current implementation, the function sets up the ethernet
chip and resets it. The steps to reset depend upon the board
revision.
The patch moves the reset actions to new function reset_net_chip().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
A large number of boards incorrectly used getenv() in their board init
code running before relocation. In some cases this caused U-Boot to
hang when certain environment variables grew too long.
Fix the code to use getenv_r().
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: The LEOX team <team@leox.org>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Georg Schardt <schardt@team-ctech.de>
Cc: Werner Pfister <Pfister_Werner@intercontrol.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Peter De Schrijver <p2@mind.be>
Cc: John Zhan <zhanz@sinovee.com>
Cc: Rishi Bhattacharya <rishi@ti.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
The reset sequence/configuration for ehci is highly board specific,
so this will be done in the source for the board, instead of
introducing several CONFIG_* which would be needed to make those
few lines in beagle.c usable across different OMAP boards.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
It is a low cost reference design based on Sitara AM3517 SoC from Texas Instruments
Please refer to <www.craneboard.org> for more details.
Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Patch was updated by Jason Kridner <jkridner@beagleboard.org>:
* Use tabs to match style of other board revisions
* Only include board revisions that exist
* Default to the same configuration as the latest revision, but
without setting 'beaglerev'
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This allows the reading of EEPROMS on the expansion bus without adding
external pull-ups.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Added LED driver using status_led. USR0 is set to monitor the boot
status. USR1 is set to be the green LED.
Included adding configuration and command to the default configuration.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
It can be optimised out by the compiler otherwise resulting
in obscure errors like a board not booting.
This has been documented in README since 2006 when these were
first fixed up for GCC 4.x.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Fix some additional places.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>
Convert the variable omap3_evm_version to u32 to work around
some broken linkers from older tool chains. E.g. CodeSourcery's
2009q1-203 ld 2.19.51.20090205. Without this, these linkers
stop linking 'omap3_evm' or at least issue a warning. Like
arm-none-linux-gnueabi-ld: section .bss [8003f5e0 -> 8007e337] overlaps section .rel.dyn [8003f5e0 -> 80044e57]
arm-none-linux-gnueabi-ld: section .dynsym [80044e58 -> 80044ef7] overlaps section.bss [8003f5e0 -> 8007e337]
arm-none-linux-gnueabi-ld: u-boot: section .bss vma 0x8003f5e0 overlaps previous sections
CC: Sanjeev Premi <premi@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Add battery charging support twl6030 driver.
Add support for battery voltage and current measurements.
Add command to get battery status and start/stop battery charging from USB.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
Function omap3_evm_get_revision() - to identify the
board revision was called at end of setup_net_chip().
Board revision can be ascertained only by identifying
the Ethernet chipset - but combining setup operations
with revision detection isn't a good idea. So, moved
the function after call to setup_net_chip().
Function setup_net_chip() should be ideally be called
only when CONFIG_CMD_NET is defined. But this leaves
the board revision "undetected". This patch allows
static definition of revision or default fallback to
the latest revision.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The function omap3_evm_need_extvbus() is required
only when USB support is configured.
Wrapped this function in #ifdef CONFIG_USB_OMAP3.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds relocation support for omap3evm.
Content of the patch is based on changes for
Beagleboard.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Beagle expansion boards contain an i2c eeprom to identify themselves.
This patch adds code to read and parse the eeprom contents. It prints
the expansion board name and revision and modifies environment variables
as appropriate. This patch is based on the Overo expansion board code.
Signed-off-by: Koen Kooi <k-kooi@ti.com>
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch switches from the legacy mmc driver to the new generic mmc driver
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
This patch switches from the legacy mmc driver to the new generic mmc driver
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
This patch adds missing pinmux setup for 4 GPIO signals used on the Beagle xM:
- USB hub reset (gpio_56)
- P8 USB hub reset (gpio_63)
- DVI enable (gpio_129)
- P8 DVI enable (gpio_170)
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch corrects the pinmux settings to enable proper functioning
of the wifi/bluetooth module.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Change the implementation for ARM V7 to relocate the code to an
arbitrary address in RAM.
Adapt the Beagle board (Cortex A8) to test the changes.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Correctly set PAD1_FREF_CLK4_REQ and PAD0_FREF_CLK4_OUT to enable and
activate both LEDs while setting pad mux.
Since this increases the line length, this patch also adjusts the white
space in this section of code to allign the pad mux signal description
comments.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@canonical.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the Beagle xM. It uses the board ID
GPIO bits to recognize this revision and perform appropriate setup.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch enhances the revision detection function and adds
support for the C4 revision. The board revision is printed
and approriate revision specific setup is done automatically.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add functional multiplexing support for OMAP4 pads.
Configure all the pads for the OMAP4430 SDP
and OMAP4 Panda boards
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds a gpmc_init function for OMAP4 and adds calls to
gpmc_init for existing OMAP4 boards: panda and sdp4430
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP4 Panda is a reference board based on OMAP4430, an ARMV7 Cortex A9 CPU
This patch adds basic support for booting the board. It includes i2c and mmc
support. It assumes U-boot is loaded to SDRAM with the help of another small
bootloader (x-load) running from SRAM. U-boot currently relies on x-load for
clock, mux, and SDRAM initialization
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP4430 SDP is a reference board based on OMAP4430, an ARMV7 Cortex A9 CPU
This patch adds basic support for booting the board. It includes i2c and mmc
support. It assumes U-boot is loaded to SDRAM with the help of another small
bootloader (x-load) running from SRAM. U-boot currently relies on x-load for
clock, mux, and SDRAM initialization
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Added function to differentiate between the OMAP3EVM revisions. The
chip-id of the ethernet PHY is being used for this purpose.
Rev A to D : 0x01150000
Rev >= E : 0x92200000
CC: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Sandeep Paulraj <s-paulraj@ti.com>
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a
bunch on on-chip integrated peripherals. This patch adds support for the
TNETV107X EVM board.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Not all boards have both LEDs hooked, so enabling both on
boards with single LED will just waste power. Make it
possible to choose LEDs by adding argument to
twl4030_led_init().
Using this turn on only LEDB for pandora, leave both LEDs
on for all other boards, as it was before this patch.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
A previous Commit converted the LAN91C96 Ethernet driver to using the
CONFIG_NET_MULTI API, but did not include full board support. This patch
finishes the job.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Enable the NET MULTI option and remove build warning
Tested: SDP3430
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Start of support of
Texas Instruments Software Development Platform(SDP)
for OMAP3430 - SDP3430
Highlights of this platform are:
Flash Memory devices:
Sibley NOR, Micron 8bit NAND and OneNAND
Connectivity:
3 UARTs and expanded 4 UART ports + IrDA
Ethernet, USB
Other peripherals:
TWL5030 PMIC+Audio+Keypad
VGA display
Expansion ports:
Memory devices plugin boards (PISMO)
Connectivity board for GPS,WLAN etc.
Completely configurable boot sequence and device mapping
etc.
Support default jumpering and:
- UART1/ttyS0 console(legacy sdp3430 u-boot)
- UART3/ttyS2 console (matching other boards,
and SDP HW docs)
- Ethernet
- mmc0
- NOR boot
Currently the UART1 is enabled by default. for
compatibility with other OMAP3 u-boot platforms,
enable the #define of CONSOLE_J9.
Conflicts:
Makefile
Fixed the conflict with smdkc100_config by moving omap_sdp3430_config
to it is alphabetically sorted location above zoom1.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Switch from space-based indentation to tab-based in mux configs, as pointed
out by WD at:
http://lists.denx.de/pipermail/u-boot/2009-September/061241.html
Nothing but whitespace changes in this patch (diff -w gives no output).
Signed-off-by: Olof Johansson <olof@lixom.net>
