Commit graph

12 commits

Author SHA1 Message Date
Marek Vasut
69ea30e688 ARM: dts: stm32: Switch to MCO2 for PHY 50 MHz clock
The LAN8710i PHY currently uses 50 MHz clock direct from PLL4P.
To permit PLL4P to run at faster frequency, use MCO2 as a divider.
The PLL4P runs at 100 MHz, supplies MCO2 which divides it by 2 to
50MHz, and supplies the PHY with 50 MHz via pin PG2. The feedback
clock are fed back in via pin PA1.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: Ia9bf7119785d49b633a3ae761c3dc4a30b92628a
2021-01-13 09:52:58 +01:00
Marek Vasut
75df748b87 ARM: dts: stm32: Disable SDMMC1 CKIN feedback clock
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2020-12-09 10:57:50 +01:00
Marek Vasut
845c6720ec ARM: dts: stm32: Enable internal pull-ups for SDMMC1 on DHCOM SoM
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2020-12-09 10:57:50 +01:00
Marek Vasut
34d573fdab ARM: dts: stm32: Drop QSPI CS2 on DHCOM
The QSPI CS2 is not used on DHCOM, remove the pinmux and flash@1.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-11-25 10:52:09 +01:00
Marek Vasut
64af7c3110 ARM: dts: stm32: Fix uSD card-detect GPIO on DHCOM
The uSD slot card-detect GPIO is connected to PG1, fix it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-11-25 10:50:44 +01:00
Marek Vasut
8791cf0923 ARM: dts: stm32: Move ethernet PHY into SoM DT
The PHY and the VIO regulator is populated on the SoM, move it
into the SoM DT.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-07-28 18:35:01 +02:00
Patrick Delaunay
1b28a5e2b0 ARM: dts: stm32mp1: DT alignment with Linux 5.7-rc2
DT alignment with Linux 5.7-rc2, including the kernel commits

431c89e6f323 ARM: dts: stm32: use correct vqmmc regu for eMMC on stm32mp1 ED1/EV1 boards
79e965053872 ARM: dts: stm32: add disable-wp property for SD-card on STM32MP1 boards
877db62ea516 ARM: dts: stm32: add cd-gpios properties for SD-cards on STM32MP1 boards
7519e95ba5f8 ARM: dts: stm32: Do clean up in stmpic nodes on stm32mp15 boards
f68e2dbc591a ARM: dts: stm32: Rename stmfx joystick pins on stm32mp157c-ev1
d6210da4f8bf ARM: dts: stm32: add cpu clock-frequency property on stm32mp15x
b65b6fc56925 ARM: dts: stm32: add wakeup-source in all I2C nodes of stm32mp157c
1c1cf5996cfb ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp157c-ed1
bef15fc0fad9 ARM: dts: stm32: add i2c2/i2c5 sleep pinctrl on stm32mp157c-ev1
b7fc0a87b9ac ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp15xx-dkx
a5e557655285 ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp15 DK boards
8bc631b650a6 ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp157c-ed1
fccd6a577bb3 ARM: dts: stm32: Correct stmfx node name on stm32mp157c-ev1 board
cc775a83db65 ARM: dts: stm32: add resets property on all DMA nodes on stm32mp151
c5fae093511b ARM: dts: stm32: enable USB OTG Dual Role on stm32mp157c-ev1
9879e2165758 ARM: dts: stm32: add USB OTG pinctrl to stm32mp15
82ac8a81f985 ARM: dts: stm32: add USB OTG full support on stm32mp151
8714b26e2863 ARM: dts: stm32: remove useless properties in stm32mp157a-avenger96 stmpic node
a7959919709e ARM: dts: stm32: Add UART8 pins A pinmux entry on stm32mp1
4d7c53a684da ARM: dts: stm32: Add USART3 pins A pinmux entry on stm32mp1
80ab128332ee ARM: dts: stm32: Add SAI2A pins B pinmux entry on stm32mp1
ab7f98c0c546 ARM: dts: stm32: Add Ethernet0 RMII pins A pinmux entry on stm32mp1

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-05-14 09:02:12 +02:00
Tom Rini
1f47e2aca4 Xilinx changes for v2020.07
common:
 - Align ENV_FAT_INTERFACE
 - Fix MAC address source print log
 - Improve based autodetection code
 
 xilinx:
 - Enable netconsole
 
 Microblaze:
 - Setup default ENV_OFFSET/ENV_SECT_SIZE
 
 Zynq:
 - Multiple DT updates/fixes
 - Use DEVICE_TREE environment variable for DTB selection
 - Switch to single zynq configuration
 - Enable NOR flash via DM
 - Minor SPL print removal
 - Enable i2c mux driver
 
 ZynqMP:
 - Print multiboot register
 - Enable cache commands in mini mtest
 - Multiple DT updates/fixes
 - Fix firmware probing when driver is not enabled
 - Specify 3rd backup RAM boot mode in SPL
 - Add SPL support for zcu102 v1.1 and zcu111 revA
 - Redesign debug uart enabling and psu_init delay
 - Enable full u-boot run from EL3
 - Enable u-boot.itb generation without ATF with U-Boot in EL3
 
 Versal:
 - Enable distro default
 - Enable others SPI flashes
 - Enable systems without DDR
 
 Drivers:
 - Gem:
   - Flush memory after freeing
   - Handle mdio bus separately
 - Watchdog:
   - Get rid of unused global data pointer
   - Enable window watchdog timer
 - Serial:
   - Change reinitialization logic in zynq serial driver
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXoxw9wAKCRDKSWXLKUoM
 IbQxAKCK23yTy4FoN8oTGTYsbmLOA9kVUQCbBx8lg4nBeA8ihSaAnY+HMDF37YI=
 =Lg54
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2020.07' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2020.07

common:
- Align ENV_FAT_INTERFACE
- Fix MAC address source print log
- Improve based autodetection code

xilinx:
- Enable netconsole

Microblaze:
- Setup default ENV_OFFSET/ENV_SECT_SIZE

Zynq:
- Multiple DT updates/fixes
- Use DEVICE_TREE environment variable for DTB selection
- Switch to single zynq configuration
- Enable NOR flash via DM
- Minor SPL print removal
- Enable i2c mux driver

ZynqMP:
- Print multiboot register
- Enable cache commands in mini mtest
- Multiple DT updates/fixes
- Fix firmware probing when driver is not enabled
- Specify 3rd backup RAM boot mode in SPL
- Add SPL support for zcu102 v1.1 and zcu111 revA
- Redesign debug uart enabling and psu_init delay
- Enable full u-boot run from EL3
- Enable u-boot.itb generation without ATF with U-Boot in EL3

Versal:
- Enable distro default
- Enable others SPI flashes
- Enable systems without DDR

Drivers:
- Gem:
  - Flush memory after freeing
  - Handle mdio bus separately
- Watchdog:
  - Get rid of unused global data pointer
  - Enable window watchdog timer
- Serial:
  - Change reinitialization logic in zynq serial driver

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-07 17:13:35 -04:00
Marek Vasut
f19312e5f4 ARM: dts: stm32: Use DT alias for the configuration EEPROM
Use DT /aliases node to establish a stable phandle to the configuration
EEPROM. This permits the configuration EEPROM to be moved e.g. to a
different address or a different bus. Adjust the board code to handle
new phandle lookup.

Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
2020-04-01 11:58:00 +02:00
Patrick Delaunay
1a4f57c895 ARM: dts: stm32mp1: DT alignment with Linux 5.6-rc1
This commit manages diversity for STM32M15x SOCs with:
- dedicated files to support all STM32MP15 SOCs family.
  The differences between those SOCs are:
  -STM32MP151 [1]: common file.
  -STM32MP153 [2]: STM32MP151 + CANs + a second CortexA7-CPU.
  -STM32MP157 [3]: STM32MP153 + DSI + GPU.
- new files to manage security diversity on STM32MP15x SOCs.
  On STM32MP15xY, "Y" gives information:
  -Y = A means no cryp IP and no secure boot.
  -Y = C means cryp IP + secure boot.
- stm32mp157 pinctrl files to better manage package diversity.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
2020-03-24 14:18:36 +01:00
Patrick Delaunay
7915b9914e stm32mp1: pwr: use the last binding for pwr
Update the driver to use the latest binding from kernel v5.5-rc1:
no more use syscon or regmap to access to pwr register and
only one pwr_regulators node with the compatibility "st,stm32mp1,pwr-reg"
is available.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13 17:26:22 +01:00
Marek Vasut
199537309b ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-02-12 19:48:39 +01:00