In commit 187af954cf there
was a typo that offset all the ecc registers by 4 bytes, fixed that.
Signed-off-by: Ben Goska <goskab@onid.oregonstate.edu>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
This patch fixes the "chip_config" command for I2C bootstrap EEPROM
configuration. First it changes the I2C bootstrap EEPROM address to
0x54 as this is used on Arches (instead of 0x52 on Canyonlands/
Glacier). Additionally, the NAND bootstrap settings are removed
for Arches since Arches doesn't support NAND-booting.
Signed-off-by: Stefan Roese <sr@denx.de>
Current code for the Monahans CPU defined OSCR_CLK_FREQ as 3.250 (MHz)
which caused floating point operations to be used. This resulted in
unresolved references to some FP related libgcc functions when using
U-Boot's private libgcc functions.
Change the code to use fixed point math only.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch updates zlib to the latest stable version.
Only relevant zlib parts were ported to u-boot tree, as already did for the
current zlib (0.95). New zlib guarantees a faster inflate performances
other then others improvements as explained at www.zlib.net.
It also includes Alessandro Rubini's patches to allow 0 as destination pointer
and to call watchdog reset if required by architecture.
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Reviewed-by: Angelo Castello <angelo.castello@st.com>
Reviewed-by: Alessandro Rubini <rubini-list@gnudd.com>
This patch adds an FTMAC100 ethernet driver for Faraday A320 evaluation board.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
For some reason the MPC8544 enabled BEDBUG if PCI was enabled and that
got copied int the MPC8536, MPC8572 and P2020 DS boards. The BEDBUG
support has never been made to work completely on e500/85xx so we
just disable it to save space and match the other FSL 85xx boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is a port of Linux driver for SDHC host controller hardware
found on Freescale's MX2 and MX3 processors. Uses new generic MMC
framework (CONFIG_GENERIC_MMC) and it looks like there are some
problems with a framework (at least on LE cpus). Some of these
problems are addressed in the following patches.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
It is recommended to define the macro CONFIG_SYS_64BIT_VSPRINTF
for NAND specific warning removal, same is done in this patch
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
It was brought to our attention that U-Boot contains code derived from the
IBM OpenBIOS source code originally provided with some of the older PowerPC
4xx development boards. As a result, the original license of this code has
been carried in the various files for a number of years in the U-Boot project.
IBM is dual-licensing the IBM code contributions already present in U-Boot
under either the terms of the GNU General Public License version 2, or the
original code license already present.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
replace variable types in ctrl_structs for omap3 by those with
fixed size (u8, u16, u32).
Additional ifndef-protection is needed by examples which do not
compile when including asm/types.h
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Based on Intel PRO/1000 Network Driver 7.3.20-k2
Add Intel E1000 PCIE card support. The following cards are added:
INTEL_82571EB_COPPER
INTEL_82571EB_FIBER,
INTEL_82571EB_SERDES
INTEL_82571EB_QUAD_COPPER
INTEL_82571PT_QUAD_COPPER
INTEL_82571EB_QUAD_FIBER
INTEL_82571EB_QUAD_COPPER_LOWPROFILE
INTEL_82571EB_SERDES_DUAL
INTEL_82571EB_SERDES_QUAD
INTEL_82572EI_COPPER
INTEL_82572EI_FIBER
INTEL_82572EI_SERDES
INTEL_82572EI
INTEL_82573E
INTEL_82573E_IAMT
INTEL_82573L
INTEL_82546GB_QUAD_COPPER_KSP3
INTEL_80003ES2LAN_COPPER_DPT
INTEL_80003ES2LAN_SERDES_DPT
INTEL_80003ES2LAN_COPPER_SPT
INTEL_80003ES2LAN_SERDES_SPT
82571EB_COPPER dual ports,
82572EI single port,
82572EI_COPPER single port PCIE cards
and
82545EM_COPPER,
82541GI_LF
pci cards are tested on both P2020 board
and MPC8544DS board.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
In the previous enetaddr refactoring, the assumption with commit 56b555a644
was that the eth layer would handle the env -> device enetaddr syncing.
This was not the case as eth_initialize() is called only once and the sync
occurs there. So make sure the eth_init() function does the env -> device
sync with every network init.
Reported-by: Andrzej Wolski <awolski@poczta.fm>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Embedd chip select configuration into struct for gpmc config
instead of having it completely separated as suggested by
Wolfgang Denk on
http://lists.denx.de/pipermail/u-boot/2009-May/052247.html
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
For some reason the AT91rm9200 lowlevel init writes to a bunch of
reserved or read-only addresses. All the boards seem to define the
value-to-be-written values as zero ... but they shouldn't actually
be writing *anything* there.
No documented erratum justifies these accesses. It looks like maybe
some pre-release BDI-2000 setup code has been carried along by cargo
cult programming since at least late 2004 (per GIT history).
Here's a patch disabling what seems to be bogosity. Tested on a
csb337; there were no behavioral changes.
Signed-off-by: David Brownell <david-b@pacbell.net>
on RM9200ek
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch moves the load addresses for kernel, fdt and ramdisk to higher
addresses (>= 16MB). This enables booting of bigger kernel images (e.g.
lockdep enabled).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes CONFIG_SYS_BOOTMAPSZ from 8MB to 16MB which is the
initial TLB on 40x PPC's in the Linux kernel. With this change even bigger
Linux kernels (> 8MB) can be booted.
This patch also sets CONFIG_SYS_BOOTM_LEN to 16MB (default 8MB) to enable
decompression of bigger images.
Signed-off-by: Stefan Roese <sr@denx.de>
These defines have been subplanted by the equivelent defines in
include/twl4030.h
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
Because twl4030 now has its own device files, move and rename
twl4030_mmc_config.
twl4030_mmc_config initializes the twl4030 power setting to
the mmc device. Because it is in the twl4030 power domain, move
it out of drivers/mmc/omap3_mmc.c and into drivers/power/twl4030.c.
The function was renamed to twl4030_power_mmc_init because all
the functions in this file are to have the format
twl4030_power_<device>_<action>
In this case the suffix is mmc_init so
device : mmc
action : init
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
Because twl4030 now has its own device files, move exiting
omap3 power_init_r to a new location.
power_init_r is the only function in board/omap3/common.
It initializes the twl4030 power for the board and enables
the led.
The power part of the the function is moved to twl4030_power_init in
drivers/power/twl4030.c The power compilation is conditional on the
existing config variable CONFIG_TWL4030_POWER.
The led part is moved to twl4030_led_init in the new file
drivers/misc/twl4030_led.c The led compilation is conditional on
the new config variable CONFIG_TWL4030_LED
The directory board/omap3/common was removed because power_init_r
was the only function in it.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
Commit 2b3f12c2 added support for configurable SMC Rx buffer length on
8xx systems. Enable this feature on TQM8xx* based boards.
This fixes the problem that pasting text in the middle of a line
(i. e. inserting in edit mode) did not work - only the first two
characters got inserted, the rest was lost.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The Zoom2 power reset button is on the top right side of the
main board. Press and hold for about to 8 seconds to completely
reset the board.
Some of the beta boards have a hardware problem that prevents
using this feature. If is difficult to further characterize the
boards that fail. So disable resetting for all beta boards.
The Zoom1 reset button is the red circle on the top right,
front of the board. Press and hold the button for 8 seconds to
completely reset the board.
After analyzing beagle, it was determined that other boards
that use the twl4030 for power managment can also make use
this function.
The resetting is done by the power management part of the twl4030.
Since there is no existing drivers/power, add one.
The compilation of power/twl4030.h is controlled by the config
variable CONFIG_TWL4030_POWER
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
The TWL4030 supplies many peripherals for OMAP3 boards. These include
power management, usb and, keyboard.
The product description is found here:
http://focus.ti.com/docs/prod/folders/print/tps65950.html
Product reference document, tps65950.pdf, is found here:
http://www.ti.com/lit/gpn/tps65950
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
This problem is seen on Zoom1 and Zoom2 in the startup and
when i2c probe is used
Before :
In: serial
Out: serial
Err: serial
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_pin: I2C_STAT=1000
I2C read: I/O error
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
Die ID #327c00020000000004013ddd05026013
Hit any key to stop autoboot: 0
OMAP3 Zoom1# i2c probe
Valid chip addresses:timed out in wait_for_bb: I2C_STAT=1000
02 03 04 05 06 07 08 09 0A 0B 0C 0D <snip>
After :
In: serial
Out: serial
Err: serial
Die ID #327c00020000000004013ddd05026013
Hit any key to stop autoboot: 0
OMAP3 Zoom1# i2c probe
Valid chip addresses: 48 49 4A 4B
The addresses are for the twl4030.
The prescalar that converts the function clock to the sampling
clock is hardcoded to 0. The reference manual recommends 7
if the function clock is 96MHz.
Instead of just changing the hardcoded values, the prescalar
is calculated from the value I2C_IP_CLK.
The i2c #defines are in kHz. The speed passed into the
i2c init routine is in Hz. To be consistent, change the
defines to be in Hz.
The timing calculations are based on what is done in the
linux 2.6.30 kernel in drivers/i2c/buses/i2c_omap.c as
apposed to what is done in TRM.
The major variables in the timing caculations are
specified as #defines that can be overriden as required.
The variables and their defaults are
I2C_IP_CLK SYSTEM_CLOCK_96
I2C_INTERNAL_SAMPLING_CLK 19200000
I2C_FASTSPEED_SCLL_TRIM 6
I2C_FASTSPEED_SCLH_TRIM 6
I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM
I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM I2C_FASTSPEED_SCLH_TRIM
I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM
I2C_HIGHSPEED_PHASE_TWO_SCLH I2C_FASTSPEED_SCLH_TRIM
This was runtime verified on Zoom1, Zoom2, Beagle and Overo.
The 400kHz and 3.4M cases were verifed on test Zoom1,
Zoom2, Beagle and Overo configurations.
Testing for omap2 will be done in a second step as Nishanth
and Jean-Christophe commented.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
DDR2 Auto-calibration needs to be disabled on the NAND booting PPC4xx
targets. Otherwise the configured fixed init values for some DDR2
controller registers (e.g. RQDC) are not initialized at all resulting
in a non working SDRAM.
Signed-off-by: Stefan Roese <sr@denx.de>
Board support for the Guntermann & Drunck CompactCenter and
DevCon-Center.
Based on the AMCC Canyonlands board support by Stefan Roese.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the esd VME8349 board equipped with the
MPC8349. It's a VME PMC carrier board equipped with the Tundra
TSI148 VME-bridge.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Up to this point in time, the sbc8349 board was storing the u-boot
image in flash 2x. One for the HRCW value at the beginning of
flash (0xff80_0000), and once close to the end of flash (0xfff8_0000)
for the actual image that got executed.
This moves the TEXT_BASE to be the beginning of flash, which makes
the second copy of the image redundant, and frees up the flash
from the end of the environment storage to the end of the flash
device itself.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Commit 7024aa14 was supposed to fix the #ifdef/#endif pairing in
include/configs/at91cap9adk.h, but did not cate all problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The reordering of include/common.h by commit fcd3c87e49 broke
boards with status LED support, resulting in
error: #error Status LED configuration missing
errors. Undo this reordering to avoid this issue.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 70ebf316 factored out the ROUND() macro into include/common.h,
not realizing that the primary use of this macro on AT91 systems was
in start.S where common.h was not included, and could not be included
because it contains a lot of C code which the assembler doesn't
understand.
This patch wraps such code in common.h in a "#ifndef __ASSEMBLY__"
construct, and then adds an include to cpu/arm926ejs/start.S thus
solving the problem.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch updates the support for EB+MCF-EV123 board and needs
the [PATCH 1/2 V3] new video driver for bus vcxk framebuffers
* remove the board framebuffer driver
* use the common bus_vcxk framebuffer driver
* adds bmp support
* adds splashimage support
* fix serveral cosmetical errors
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
[agust@denx.de: fixed some style issues before applying]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch adds a new video driver
* adds common bus_vcxk framebuffer driver
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
[agust@denx.de: fixed lots of style issues before applying]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
include/lcd.h has different vidinfo for different platforms,
and several extern declaration, but one for the default case was
missing. This makes them a single extern declaration for everyone.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
This patch adds support for the AVR32 LCD controller. This patch is
based off the latest u-boot-video.
A quick summary of what's going on:-
Enable LCDC pixel clock
Enable LCDC port pins
Add framebuffer pointer to global_data struct
Allocate framebuffer
To use the new code, update your board config to include something like
this:-
#define CONFIG_LCD 1
#if defined(CONFIG_LCD)
#define CONFIG_CMD_BMP
#define CONFIG_ATMEL_LCD 1
#define LCD_BPP LCD_COLOR16
#define CONFIG_BMP_16BPP 1
#define CONFIG_FB_ADDR 0x10600000
#define CONFIG_WHITE_ON_BLACK 1
#define CONFIG_VIDEO_BMP_GZIP 1
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE 262144
#define CONFIG_ATMEL_LCD_BGR555 1
#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
#define CONFIG_SPLASH_SCREEN 1
#endif
The standard U-Boot BMP and Splash-screen features should just work.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
[agust@denx.de: fixed some style issues]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This moves some extern declaration from lcd.c to lcd.h, removing
unneeded ifdef around a pair of them. Additionally, since
gunzip_bmp() was declared static in cmd_bmp.c but extern in lcd.c, I
removed the static. The extra "#include <lcd.h>" in cmd_bmp.c is
added to ensure the header is consistent with the source.
This has been compile-tested on both ARM (at91 boards) and PowerPC
(HH405_config, TQM823L_LCD_config, mcc200_config), to test all use
combinations.
Signed-off-by: Alessandro Rubini <rubini@gnudd.it>
[agust@denx.de: removed gunzip_bmp() fixes as commit c01171ea did it]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This reverts commit b201171f2b.
The commit caused problems for example when unpacking kernel images:
Uncompressing Kernel Image ... Error: inflate() returned -2
GUNZIP: uncompress, out-of-mem or overwrite error - must
RESET board to recover
Conflicts:
include/u-boot/zlib.h
lib_generic/zlib.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch removes the "alterpll" command and replaces it with the now
ppc4xx standard "chip_config" command to configure the I2C bootstrap
EEPROM.
Signed-off-by: Stefan Roese <sr@denx.de>
Kilauea has an AT24C02 EEPROM which has an 8 byte page. Without defining
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS to 3 the "eeprom" command doesn't
work correctly.
Additionally the page write delay (CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS)
is set to a more defensive value of 10ms.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds a generic command for programming I2C bootstrap
eeproms on PPC4xx. An implementation for Canyonlands board is
included.
The command name is intentionally chosen not to be PPC4xx specific.
This way other CPU's/SoC's can implement a similar command under
the same name, perhaps with a different syntax.
Usage on Canyonlands:
=> chip_config
Available configurations (I2C address 0x52):
600-nor - NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100
600-nand - NAND CPU: 600 PLB: 200 OPB: 100 EBC: 100
800-nor - NOR CPU: 800 PLB: 200 OPB: 100 EBC: 100
800-nand - NAND CPU: 800 PLB: 200 OPB: 100 EBC: 100
1000-nor - NOR CPU:1000 PLB: 200 OPB: 100 EBC: 100
1000-nand - NAND CPU:1000 PLB: 200 OPB: 100 EBC: 100
1066-nor - NOR CPU:1066 PLB: 266 OPB: 88 EBC: 88 ***
1066-nand - NAND CPU:1066 PLB: 266 OPB: 88 EBC: 88
=> chip_config 600-nor
Using configuration:
600-nor - NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100
done (dump via 'i2c md 52 0.1 10')
Reset the board for the changes to take effect
Other 4xx boards will be migrated to use this command soon
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
The XPedite1000 is an X-ES product thus it can be put in board/xes along
with other X-ES boards. Along with the move, the board was renamed to
XPedite1000 from XPedite1K to fit X-ES's standard naming convention.
Maintainership was also transfered to Peter Tyser.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The XPedite1000 only has 2 available ethernet ports:
ppc_4xx_eth2 (EMAC2) and ppc_4xx_eth3 (EMAC3)
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Previously an I2C EEPROM was used. The EEPROM had size, reliability,
and access issues which are resolved by storing the environment in
flash.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The XPedite1000 can be built with 4 total flashes:
- 512KB AMD socketed
- 16MB Intel soldered
- 2 x 32MB AMD MirrorBit flashes
Add support for the optional 2 32MB CFI-compliant AMD flashes
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
By default, the XPedite1000 comes installed with xMon, a proprietary
bootloader. xMon stores its MAC address in an onboard EEPROM. Rather
than requiring a non-standard location in the EEPROM to be reserved for
MAC addresses, store the MAC addresses in U-Boot's standard environment.
A U-Boot application or OS application can be used to migrate xMon MAC
addresses to U-Boot's environment if necessary.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Using the CFI flash driver will allow write access to the 16MB Intel
StrataFlash present on the XPedite1000. The 512KB socketed (non
CFI-compliant flash) will no longer be writable.
The mapping of the 16MB Strata flash was moved to 0xff000000 and the
512KB AMD socketed flash was moved to 0xfe000000.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds I2C support for mvBC-P and defines flash layout
matching the shipped product.
Signed-off-by: Andr Schwarz <andre.schwarz@matrix-vision.de>
This patch updates zlib to the latest stable version.
Only relevant zlib parts were ported to u-boot tree, as was done for
the previously used version of zlib (0.95). New zlib gives faster
inflate performance and other improvements, see www.zlib.net
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Reviewed-by: Angelo Castello <angelo.castello@st.com>
Edited commit message
Signed-off-by: Wolfgang Denk <wd@denx.de>
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
- changed CONFIG_DRIVER_SMC911X* to CONFIG_SMC911X*
- cleaned up line lengths
- modified all boards that override weak function in this driver
- added
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Tested-by: Mike Frysinger <vapier@gentoo.org>
On 04 Oct 2008 Pieter posted a dns implementation for U-Boot.
http://www.mail-archive.com/u-boot-users@lists.sourceforge.net/msg10216.html
>
> DNS can be enabled by setting CFG_CMD_DNS. After performing a query,
> the serverip environment var is updated.
>
> Probably there are some cosmetic issues with the patch. Unfortunatly I
> do not have the time to correct these. So if anybody else likes DNS
> support in U-Boot and has the time, feel free to patch it in the main tree.
Here it is again - slightly modified & smaller:
- update to 2009-06 (Pieter's patch was for U-Boot 1.2.0)
- README.dns is added
- syntax is changed (now takes a third option, the env var to store
the result in)
- add a random port() function in net.c
- sort Makefile in ./net/Makefile
- dns just returns unless a env var is given
- run through checkpatch, and clean up style issues
- remove packet from stack
- cleaned up some comments
- failure returns much faster (if server responds, don't wait for
timeout)
- use built in functions (memcpy) rather than byte copy.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Pieter Voorthuijsen <pieter.voorthuijsen@prodrive.nl>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The net code is mostly consistent in using 'Packet' rather than 'Pkt', so
rename the minor detractor to follow suite.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This is Marvell's 88F6281_A0 based reference design board
This patch is tested for-
1. Boot from DRAM/NAND flash/NFS
2. File transfer using tftp and loadb
3. NAND flash read/write/erase
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Use the MPC8572's eLBC to access 1 GB (or greater) onboard NAND flash
via the 'nand' command.
Previously, the XPedite5370's NAND chip selects were properly
configured, but NAND support was not enabled.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Increasing CONFIG_SYS_BOOTM_LEN from 8 MB to 16 MB is necessary to
support uncompressing images larger than 8 MB when using the bootm
command.
Note that recent Linux kernels for the 85xx and 86xx map greater than
16MB of memory on bootup, but we use 16MB to maintain compatibility with
older Linux kernels for now.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Buffered writes are possible on the XPedite5200 and XPedite5370 and greatly
improve NOR flash write speeds
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rename sdram_mode_1 to sdram_mode and sdram_cfg_1 to sdram_cfg to match
the 86xx user's manual and other Freescale architectures
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p2020DS, MPC8536DS, MPC8572DS, MPC8544DS boards are capable of
swizzling the upper address bits of the NOR flash we boot out of which
creates the concept of "virtual" banks. This is useful in that we can
flash a test of image of u-boot and reset to one of the virtual banks
while still maintaining a working image in "bank 0".
The PIXIS FPGA exposes registers on LBC which we can use to determine
which "bank" we are booting out of (as well as setting which bank to
boot out of).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8641HPCN board is capable of swizzling the upper address bit of
the NOR flash we boot out of which creates the concept of "virtual"
banks. This is useful in that we can flash a test of image of u-boot
and reset to one of the virtual banks while still maintaining a
working image in "bank 0".
The PIXIS FPGA exposes registers on LBC which we can use to determine
which "bank" we are booting out of (as well as setting which bank to
boot out of).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
