DMSC can use certain amount of msmc memory available in the
system. Also certain part of msmc memory can be marked as L3
cache using board config. But users might not know what size
is being used and the remaining available msmc memory. In order
to fix this TISCI protocol provides a messages that can query
the available msmc memory in the system. Add support for this
message.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now that NAND is supported on DRA71x include various NAND environment
settings
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In order to fully support SPL_OF_CONTROL, we need BSS to be a bit
larger. This patch relocates BSS to SDRAM instead of SRAM which
is similar to how ARMv7 boards (like OMAP2+) do it.
This means two new variables are required:
CONFIG_SPL_BSS_START_ADDR set to DAVINCI_DDR_EMIF_DATA_BASE
CONFIG_SPL_BSS_MAX_SIZE is set to 0x1080000 which is 1 byte
before the location where U-Boot will load.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch update the behavior introduced by
commit 96907c0fe5 ("dm: spi: Read default speed and mode values from DT")
In case of DT boot, don't read default speed and mode for SPI from
CONFIG_* but instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.
Remove also use in boards of the value speed=0 (no more supported)
for ENV in SPI by using CONFIG_ENV_SPI_MAX_HZ=0.
DT values will be always used when available (full DM support of
SPI slave with available DT node) even if speed and mode are requested;
for example in splash screen support (in splash_sf_read_raw)
or in SPL boot (in spl_spi_load_image).
The caller of spi_get_bus_and_cs() no more need to force speed=0.
But the current behavior don't change if the SPI slave is not
present (device with generic driver is created automatically)
or if platdata is used (CONFIG_OF_PLATDATA).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
mtd_oobavail() returns either mtd->oovabail or mtd->oobsize. Both
values are unsigned 32-bit entities, so there is no reason to pretend
returning a signed one.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The DB-XC3-24G4XG is a switch development board from Marvell. It can
either use and external CPU card such as the db-88f6820-amc or the
internal CPU that is integrated into the switch.
Add support for running U-Boot on the internal CPU and enable the USB,
SPI and NAND peripherals. For now this needs the bin_hdr from the
Marvell U-Boot for this board.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Switch from legacy IDE driver to sata_mv driver.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Following commits abe66b1b5d ("Convert CONFIG_ENV_SPI_* to Kconfig")
and 14453fbfad ("Convert CONFIG_SF_DEFAULT_* to Kconfig") remove
dandling comment lines and empty #ifdef sections.
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The fdtdec_get_carveout() and fdtdec_set_carveout() function can be used
to read a carveout from a given node or add a carveout to a given node
using the standard device tree bindings (involving reserved-memory nodes
and the memory-region property).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function can be used to add subnodes in the /reserved-memory node.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These helpers can be used to unpack variables of type fdt_addr_t and
fdt_size_t into a pair of 32-bit variables. This is useful in cases
where such variables need to be written to properties (such as "reg")
of a device tree node where they need to be split into cells.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These macros are useful for converting the endianness of variables of
type fdt_addr_t and fdt_size_t.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The function dm_ofnode_pre_reloc should be used instead
of the function dm_fdt_pre_reloc and avoid duplicated code.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit 5ff7768892.
As noted in the comment, the function pinctrl_decode_pin_config_dm()
only served as a temporary solution.
Since the function has no users anymore, we can remove it again.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Merge drivers/soc/keystone/ into drivers/soc/ti/
and convert CONFIG_TI_KEYSTONE_SERDES into Kconfig.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The UDMA-P is intended to perform similar (but significantly upgraded) functions
as the packet-oriented DMA used on previous SoC devices. The UDMA-P module
supports the transmission and reception of various packet types.
The UDMA-P also supports acting as both a UTC and UDMA-C for its internal
channels. Channels in the UDMA-P can be configured to be either Packet-Based or
Third-Party channels on a channel by channel basis.
The initial driver supports:
- MEM_TO_MEM (TR mode)
- DEV_TO_MEM (Packet mode)
- MEM_TO_DEV (Packet mode)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Add TI Communications Port Programming Interface (CPPI) 5
interface description and helpers
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Ring Accelerator (RINGACC or RA) provides hardware acceleration to
enable straightforward passing of work between a producer and a consumer.
There is one RINGACC module per NAVSS on TI AM65x SoCs.
The RINGACC converts constant-address read and write accesses to equivalent
read or write accesses to a circular data structure in memory. The RINGACC
eliminates the need for each DMA controller which needs to access ring
elements from having to know the current state of the ring (base address,
current offset). The DMA controller performs a read or write access to a
specific address range (which maps to the source interface on the RINGACC)
and the RINGACC replaces the address for the transaction with a new address
which corresponds to the head or tail element of the ring (head for reads,
tail for writes). Since the RINGACC maintains the state, multiple DMA
controllers or channels are allowed to coherently share the same rings as
applicable. The RINGACC is able to place data which is destined towards
software into cached memory directly.
Supported ring modes:
- Ring Mode
- Messaging Mode
- Credentials Mode
- Queue Manager Mode
TI-SCI integration:
Texas Instrument's System Control Interface (TI-SCI) Message Protocol now
has control over Ringacc module resources management (RM) and Rings
configuration.
The Ringacc driver manages Rings allocation by itself now and requests
TI-SCI firmware to allocate and configure specific Rings only. It's done
this way because, Linux driver implements two stage Rings allocation and
configuration (allocate ring and configure ring) while TI-SCI Message
Protocol supports only one combined operation (allocate+configure).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Texas Instruments' System Control Interface (TI-SCI) Message Protocol
abstracts management of NAVSS resources, like PSI-L pairing and
unpairing, UDMAP tx/rx/flow configuration and Rings.
This patch adds support for requesting and configuring such resources
from TI-SCI firmware.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
The 'u-boot,i2c-transaction-bytes' device tree property provides
information regarding number of bytes transferred by a device in a
single transaction.
This change is necessary to avoid hanging devices after soft reset.
One notable example is communication with MC34708 device:
1. Reset when communicating with MC34708 via I2C.
2. The u-boot (after reboot -f) tries to setup the I2C and then calls
force_idle_bus. In the same time MC34708 still has some data to be sent
(as it transfers data in 24 bits chunks).
3. The force_idle_bus() is not able to make the bus idle as 8 SCL
clocks may be not enough to have the full transmission.
4. We end up with I2C inconsistency with MC34708.
This PMIC device requires 24+ SCL cycles to make finish any pending I2C
transmission.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
LibreTech AC is a single board computer manufactured by Libre Technology
with the following specifications:
- Amlogic S805X ARM Cortex-A53 quad-core SoC @ 1.2GHz
- ARM Mali 450 GPU
- 512MiB DDR4 SDRAM
- 10/100 Ethernet
- HDMI 2.0 4K/60Hz display
- 40-pin GPIO header
- 4 x USB 2.0 Host
- eMMC, SPI NOR Flash
- Infrared receiver
The u-boot specific code is the same as the P212 support,
so use the P212 board support code with a distinct defconfig
and config include files.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The command line is:
ln <interface> <dev[:part]> target linkname
Currently symbolic links are supported only in ext4 and only if the option
CMD_EXT4_WRITE is enabled.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Re-use the functions used to write/create a file, to support creation of a
symbolic link.
The difference with a regular file are small:
- The inode mode is flagged with S_IFLNK instead of S_IFREG
- The ext2_dirent's filetype is FILETYPE_SYMLINK instead of FILETYPE_REG
- Instead of storing the content of a file in allocated blocks, the path
to the target is stored. And if the target's path is short enough, no block
is allocated and the target's path is stored in ext2_inode.b.symlink
As with regulars files, if a file/symlink with the same name exits, it is
unlinked first and then re-created.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix ext4 env code]
Signed-off-by: Tom Rini <trini@konsulko.com>
There is no need to modify the buffer passed to ext4fs_write_file().
The memset() call is not required here and was likely copied from the
equivalent part of the ext4fs_read_file() function where we do need it.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When a file contains extents, U-Boot currently reads extent-related data
for each block in the file, even if that data is located in the same
block each time. This significantly slows down loading of files that use
extents. Implement a very dumb cache to prevent repeatedly reading the
same block. Files with extents now load as fast as files without.
Note: There are many cases where read_allocated_block() is called. This
patch only addresses one of those places; all others still read redundant
data in any case they did before. This is a minimal patch to fix the
load command; other cases aren't fixed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Increase the USB power good delay on Alt, this is required with
certain USB sticks, otherwise they might not be detected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add required Kconfig symbols, Makefile bits and macro fixes in a
few places to support LZO and DT compression in U-Boot. This can
save a lot of space with multi-DTB fitImages.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Split fdtdec_setup_memory_banksize() into fdtdec_setup_memory_banksize_fdt(),
which allows the caller to pass custom blob into the function and the
original fdtdec_setup_memory_banksize(), which uses the gd->fdt_blob. This
is useful when configuring the DRAM properties from a FDT blob fragment
passed in by the firmware.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Split fdtdec_setup_mem_size_base() into fdtdec_setup_mem_size_base_fdt(),
which allows the caller to pass custom blob into the function and the
original fdtdec_setup_mem_size_base(), which uses the gd->fdt_blob. This
is useful when configuring the DRAM properties from a FDT blob fragment
passed in by the firmware.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcrEcDAAoJEB6zHgIOrC/I1dgH/3mHQNW8bqiNCJYcoVQdheHb
e06TqbWHNlOG/NilYybvdeF+LjeCqhX4PzyL/sdcyBf3D/tK4cVvHpZrQyjb2s6K
5IZSKJ+cZznmq6Hv7b//d30Azhx8bi8luxs60kkj+PF0xI1EyU3JteUqAs4Ooxd7
z+HdcRFuAaps6sy0+szB3fTw9HTGrhFvQuHasDGb2uahhpwGzu/P0RchIDksOdzH
3L4EOvgq8MZCiZ3ZtFWMWzQoCjcKf5Fuux41qar8gG/LrkWRfKG+LfWfZtTiTsjf
vC9bYWmdKtkSLFj1PWgLBfGxev5zwPUbqI2EP4OlagfNs3os5pVFCYV5NZ6ovdE=
=kMXf
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.07-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel features and fixes for 2019.07 cycle
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip
AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage.
This patch adds support for this board including SPL support. Therefore
the AT91Boostrap is not needed on this platform any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds the necessary defines to the Siemens AT91SAM based
boards (smartweb, corvus and taurus) to generate the combined binary
image with SPL and main U-Boot image combined (u-boot-with-spl.bin).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
This patch adds some checks, so that the watchdog can be enabled in main
U-Boot proper but can be disabled in SPL.
This will be used by some AT91SAM based boards, which might enable the
watchdog in the main U-Boot proper and not in SPL. It will be enabled in
SPL by default there, so no need to configure it there. This approach
saves some space in SPL.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
Migrate the following options to CONFIG_DM:
CONFIG_DM_GPIO
CONFIG_DM_MMC
CONFIG_DM_ETH
CONFIG_DM_SERIAL
CONFIG_DM_USB
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Those two functions will be used later to re-implement do_bootefi_exec().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
To meet UEFI spec v2.7a section 9.2, we should add
EFI_LOADED_IMAGE_DEVICE_PATH_PROTOCOL to image handle,
instead of EFI_DEVICE_PATH_PROTOCOL.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently, image's image_base points to an address where the image was
temporarily uploaded for further loading. Since efi_loader relocates
the image to final destination, image_base and image_size should reflect
that.
This bug was detected in UEFI SCT, "Loaded Image Protocol Test - test 2,"
which shows that 'Unload' function doesn't fit into a range suggested by
image_base and image_size.
TestCase/UEFI/EFI/Protocol/LoadedImage/BlackBoxTest/
LoadedImageBBTestMain.c:1002
Changes in this patch also includes:
* reverts a patch, "efi_loader: save image relocation address
and size" since newly added fields are no longer needed.
* copy PE headers as well since those information will be needed
for module loading, in particular, at gurb.
(This bug was reported by Heinrich.)
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Rebase patch.
Remove unused fields from struct efi_loaded_image_obj.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
After running tools/moveconfig.py it turned out that for various boards
there are an empty #ifdef statements.
Remove them to clean u-boot source code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
With UUID support, the root can now point to UUID. This makes
swiching between mmc 0 and mmc 1 easier by simplying changing
mmcdev between 0 and 1. From there, the scripts handle the rest.
Signed-off-by: Adam Ford <aford173@gmail.com>
Commit d245059ff7 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
only fixed the superfluous CONFIG_SYS_BOOTMAPSZ for R-Car Gen3, even
though it listed all affected boards. Apply the same fix to Gen2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Fixes: d245059ff7 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
The FIT image is loaded to 0x8700_0000 followed by extracting from that
several large images also into the 0x8x00_0000 range. Large images
can end up overwriting the FIT image as it is being extracted from.
Move the FIT load address clear out to 0x9000_0000, this will require
a board to have at least 256MB of DRAM, if less then more careful
planning will be required for that platform.
Signed-off-by: Andrew F. Davis <afd@ti.com>
This patch series contains a bug fix for a double free in a UEFI unit
test. The other patches are documentation only (except for the definition
of two additional constants).
-----BEGIN PGP SIGNATURE-----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=UiND
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-04-rc5-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI system for v2019.04-rc5-2
This patch series contains a bug fix for a double free in a UEFI unit
test. The other patches are documentation only (except for the definition
of two additional constants).
On AXS10x boards we have non-standard NAND controller
which was never really used a lot as there're other much more
convenient [as they are standard & removable] persistent media
like SD-card and USB mass storage.
Moreover after recent changes we face with some NAND controller
runtime issues. So instead of keeping support of yet another
non-standard peripheral we're dropping its support for good.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We currently only support EFI_FILE_PROTOCOL_REVISION while
UEFI specs 2.4 - 2.7 prescribe EFI_FILE_PROTOCOL_REVISION2.
Add a todo.
Add missing constants for the EFI file protocol revision.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED
I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Replace CONFIG_ENV_SPI_BASE by the better CONFIG_SYS_SPI_BASE
(it is not the location for environment but the location for U-Boot)
and, as it is the only platform with use this define, remove
it from whitelist.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Move some configurations in defconfig file
- CONFIG_CMD_I2C
- CONFIG_CMD_SPI
This allow correct dependency handling in Kconfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Move some configurations in defconfig file
- CONFIG_DM_SPI (removed by syncing defconfigs )
- CONFIG_CMD_SF
- CONFIG_CMD_SPI
- CONFIG_CMD_SF_TEST
This allow correct dependency handling in Kconfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
U-Boot doesn't support metadata_csum feature. Writing to filesystem with
metadata_csum feature makes the filesystem corrupted and unbootable by
Linux:
[ 2.527495] EXT4-fs (mmcblk0p2): ext4_check_descriptors: Checksum for group 0 failed (52188!=0)
[ 2.537421] EXT4-fs (mmcblk0p2): ext4_check_descriptors: Checksum for group 1 failed (5262!=0)
...
[ 2.653308] EXT4-fs (mmcblk0p2): ext4_check_descriptors: Checksum for group 14 failed (42611!=0)
[ 2.662179] EXT4-fs (mmcblk0p2): ext4_check_descriptors: Checksum for group 15 failed (21527!=0)
[ 2.687920] JBD2: journal checksum error
[ 2.691982] EXT4-fs (mmcblk0p2): error loading journal
[ 2.698292] VFS: Cannot open root device "mmcblk0p2" or unknown-block(179,2): error -74
Don't write to filesystem with meatadata_csum feature to not corrupt the
filesystem.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
This patch adds a comment to the header with the PCI_foo macros related
to DEVFN to explain the difference in U-Boot vs Linux.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_SYS_HELP_CMD_WIDTH is used to format the output of help without any
arguments.
CONFIG_SYS_HELP_CMD_WIDTH = 8 is too narrow to fit all our commands.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
To boot from fpga on socfpga gen5, we need to set CONFIG_SPL_TEXT_BASE to
0xC0000000 (hps2fpgaslaves base address).
Since converting CONFIG_SPL_TEXT_BASE to Kconfig hasn't been successful so
far, let's make this value overridable in socfpga_common.h, so that we can
have different board configs override this in socfpga_common.h.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
A few scripts reference 'fdt_addr' when they should reference
'fdt_addr_r' so this patch fixes those broken references.
Signed-off-by: Adam Ford <aford173@gmail.com>
Combined with watchdog board reset mechanism, this can be used as recovery
boot option after bootlimit exceeds the configured value.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Currently the command "saveenv" is not available.
The CONFIG_ENV_IS_IN_MMC symbol has been converted to Kconfig,
so fix the problem by moving it to the defconfig.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Convert to use DM_PMIC for the PFUZE3000. Since this PMIC is
under an I2C bus, conver to DM_I2C as well.
Also, since I2C is not used in SPL, remove CONFIG_SPL_I2C_SUPPORT
to avoid build warnings.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Various places in the code set "boardname" env property. It was used
for booting from ITB images and choosing proper DTB file name. Instead
of duplicating it, use existing U-Boot wide - "board_name".
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
File mixed space and tab indentation. Unify it.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When including other header from configs, use consistent <> syntax.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Changing voltage and enabling regulator might require delays so the
regulator stabilizes at expected level.
Add support for "regulator-ramp-delay" binding which can introduce
required time to both enabling the regulator and to changing the
voltage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Detection of board revision is done early - before power setup. In case of
Odroid XU3/XU4/HC1 family, the detection is done using ADC which
is supplied by LDO4/VDD_ADC regulator. This regulator could be turned
off (e.g. by kernel before reboot). If ADC is used early, the
regulators are not yet available and the detection won't work.
Split the revision detection out of set_board_type() into separate
function called later - either when displaying board info (in late mode)
or during misc_init_r. The idea is that set_board_type() will be called
early so its method of detection are limited to flattened device tree
(exynos5-dt-types.c for Exynos5) or GPIO (odroid.c for Exynos4412). The
newly added set_board_revision() can be called only later, when
resources like regulator are available.
This is necessary to fix the detection of Odroid HC1 after reboot, if
kernel turned off the LDO4 regulator.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The SPL size on Gen5 is 4*64kiB, but on A10 it is 4*256kiB.
Handle the difference.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
This is not used anywhere, so drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The bootrom seems to leave the D-cache in messed up state, make sure
the SPL disables it so it can not interfere with operation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
v2019.01 commit 07a8060a12 ("ARM: rmobile: Convert to bootm_size")
attempted converting to bootm_size of 256 MiB below targets:
- include/configs/alt.h
- include/configs/gose.h
- include/configs/koelsch.h
- include/configs/lager.h
- include/configs/porter.h
- include/configs/rcar-gen3-common.h
- include/configs/silk.h
- include/configs/stout.h
The update didn't fully work on R-Car3 due to the
CONFIG_SYS_BOOTMAPSZ=8MiB definition left by v2016.09 commit
e525d34b47 ("ARM: rmobile: Add support salvator-x board"),
which is explained in below README excerpt:
----8<----
CONFIG_SYS_BOOTMAPSZ:
[..] If CONFIG_SYS_BOOTMAPSZ is undefined,
then the value in "bootm_size" will be used instead.
----8<----
Allow the original commit to accomplish its purpose on R-Car3 targets
by removing the CONFIG_SYS_BOOTMAPSZ definition.
Fixes: 07a8060a12 ("ARM: rmobile: Convert to bootm_size")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Enable DM_SPI and DM_SPI_FLASH in U-Boot on H2 Stout, M2W Porter and E3 Silk.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
With this patch which adds a removable USB mass storage to a list
of bootable devices, USB boot is supported in distro boot if UEFI is
configured.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
On Layerscape architectures the SEC memory map is 1MB and the
register blocks contained in it are 64KB aligned, not 4KB as
the ccsr_sec structure currently assumes. Fix the layout of
the structure for these architectures.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
dhcp boot is a useful feature and works out-of-the-box on these
platforms. Enable it as a boot source.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Default environment variable is more complete. Also scans for efi
binaries for example.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
dhcp boot is a useful feature and works out-of-the-box on these
platforms. Enable it as a boot source.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Default environment variable is more complete. Also scans for efi
binaries for example.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
dhcp boot is a useful feature and works out-of-the-box for ls2088a
platforms. Moreover, no solid reason is given for disabling it.
Revert the patch to re-enable it.
This reverts commit aea5cd75e6.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Default environment variable is more complete. Also scans for efi
binaries for example.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
dhcp boot is a useful feature and works out-of-the-box for ls1088a
platforms. Moreover, no solid reason is given for disabling it.
Revert the patch to re-enable it.
This reverts commit 863e42e8b1.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch adds SiFive FU540 board support. For now, only
SiFive serial, SiFive PRCI, and Cadance MACB drivers are
only enabled. The SiFive FU540 defconfig by default builds
U-Boot for S-Mode because U-Boot on SiFive FU540 will run
in S-Mode as payload of BBL or OpenSBI.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add driver code for the SiFive FU540 PRCI IP block. This IP block
handles reset and clock control for the SiFive FU540 device and
implements SoC-level clock tree controls and dividers.
Based on code written by Wesley Terpstra <wesley@sifive.com>
found in commit 999529edf517ed75b56659d456d221b2ee56bb60 of:
https://github.com/riscv/riscv-linux
Boot and PLL rate change were tested on a SiFive HiFive Unleashed
board.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
"env [print|set] -e" allows for handling uefi variables without
knowing details about mapping to corresponding u-boot variables.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is the same migration path as commit b6251db8c3 ("Kconfig:
Introduce USE_BOOTCOMMAND and migrate BOOTCOMMAND").
I also moved the description in README to the Kconfig help.
I ripped off the sentence about 'LWMON' since it is gone already.
I only let my boards migrate, leaving the rest to platform maintainers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Add support for sound.
Albeit the big changeset, changes are pretty limited to x86 only and a
few new sound drivers used by x86 so I think it would be good to have
this in the next release.
The CONFIG_KEYBOARD does nothing as it's legacy and unused
so just drop it from the config.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Migrate TEGRA_KEYBOARD from headers to Kconfig, only the seaboard uses it but we
drop CONFIG_KEYBOARD as the driver doesn't use the legacy drv_keyboard_init.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Migrate USB_EHCI_TEGRA from headers to Kconfig
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peter.Chubb@data61.csiro.au
Cc: Lucas Stach <dev@lynxeye.de>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Migrate SYS_I2C_TEGRA from headers to Kconfig
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peter.Chubb@data61.csiro.au
Cc: Lucas Stach <dev@lynxeye.de>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Booting recently Linux -next kernels on 32-bit Tegra devices has been
failing when using the 'multi_v7_defconfig' kenrel configuration because
the size of has grown such that it is overwriting the FDT blob.
Current Linux -next kernels built with the 'multi_v7_defconfig' have a
total size of ~19.5MB (where .text is ~12.5MB, .data is ~6.5MB and .bss
is ~0.5MB). Therefore, increase the memory location reserved for the
Linux kernel to 32MB from 16MB for 32-bit Tegra devices.
This change has been boot tested on Tegra20 Ventana, Tegra30 Cardhu and
Tegra124 Jetson TK1 with the Linux next tree (20190212).
Signed-off-by: Jonathan Hunter <jonathanh@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
All other Tegra devices that define USB_EHCI_TXFIFO_THRESH use hex
representation, fix tegra20 to be the same format.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There's a number of dangling comments in various tegra configs post migrations
of various configs so lets clean them up.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Peter.Chubb@data61.csiro.au
Cc: Lucas Stach <dev@lynxeye.de>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Allen Martin <amartin@nvidia.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Intel High-definition Audio is a newer-generation audio system which
provides for transfer of a large number of audio stream, each containing
up to 16 channels.
Add support for HDA as a library which can be used by other drivers.
U-Boot currently uses only two channels (stereo).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some audio codecs such as Intel HDA do not need to use digital data to
play sounds, but instead have a way to emit beeps. Add this interface as
an option. If the beep interface is not supported, then the sound uclass
falls back to the I2S interface.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This method in the sound API is optional since some drivers can do this
when probing or as part of SoC init. Mark it as such.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a way check to whether HD audio is enabled. Use ioctl() to avoid
adding too many unusual operations to PCH.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the PCH has 4 operations and these are reasonably widely used
in the drivers. But sometimes we want to add rarely used operations, and
each of these currently adds to the size of the PCH operations table.
Add an ioctl() method which can be easily expanded without any more impact
on the operations table.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a few IDs for common HDA blocks and the ADSP used on samus.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is platdata, not private data, so the comment is currently incorrect.
Fix it to avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is not used outside this file so make it static.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present it is possible to '#define DEBUG' at the top of a file which
causes all debug() statements in that file to become active. There is
currently no equivalent with logging, but this is a useful function.
Add a LOG_DEBUG define along with documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The log level numbers in the Kconfig are not actually correct. Fix them
and also add a missing space in the header-file comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The other OMAP3 based Logic PD boards have Falcon Mode enabled,
so this patch makes it possible on the AM3517-evm as well.
Signed-off-by: Adam Ford <aford173@gmail.com>
Current Hikey configuration allows us to store u-boot environment on uSD
card. But this will be useless if uSD card is not inserted, hence use
the onboard eMMC memory for storing environment at Boot1 partition.
While we are at it, let's increase the boot delay to 10s also.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
SPL currently does not check uImage CRCs when loading U-Boot.
This patch adds checking the uImage CRC when SPL loads U-Boot. It does
this by reusing the existing config option SPL_CRC32_SUPPORT to allow
leaving out the CRC check on boards where the additional code size or
boot time is a problem (adding the CRC check currently adds ~1.4 kByte
to flash).
The SPL_CRC32_SUPPORT config option now gets enabled by default if SPL
support for legacy images is enabled to check the CRC on all boards
that don't actively take countermeasures.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit converts the brxre1 board to DM,
for this we have todo following things:
- add a devicetree-file for this board
- drop all obsolete settings from board header-file
- use dm_i2c_xxx calls for read/write to the resetcontroller
- request gpios before operate them
Serues-cc: trini@konsulko.com
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Moves FSL_TZASC_400 and FSL_TZPC_BP147 configs to Kconfig
for LS1088A and LS2088A platforms.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Due to the new layout of Layerscape series, move the QE
firmware to address (512*4A00) in SD Card.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
nand_bootcmd doest not exist, it should be support
for nand auto boot up.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Adds esbc validate command for verification of MC and DPC
firmware, along with secure boot defconfig.
Also enable distro boot.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[PK: squash "enable DM support for SATA patch" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-----BEGIN PGP SIGNATURE-----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=BbQI
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-04-rc2' of https://github.com/xypron2/u-boot
The patches fix multiple errors. Mentionable are:
- EFI unit tests (bootefi selftest) can run on i386.
- `make tests` executes the Unicode unit tests.
The LoadImage patch is preparing for further rework to be delivered
in v2019.07.
Poll for iDMAC TX/RX interrupt before disable DMA.
This to prevent disable DMA before data is transfer
completed.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Older kernel versions or systems which do not connect eMMC reset line
properly may not be able to handle situations where either the eMMC
is left in HS200/HS400 mode or SD card in UHS modes by the bootloader
and may misbehave. Downgrade the eMMC to HS/HS52 mode and/or SD card
to non-UHS mode before booting the kernel to allow such older kernels
to work with modern U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Remove the duplicate code in efi_do_enter() and use efi_start_image() to
start the image invoked by the bootefi command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Up to now efi_load_pe() returns the entry point or NULL in case of an
error. This does not allow to return correct error codes from LoadImage().
Let efi_load_pe() return a status code and fill in the entry point in the
corresponding field of the image object.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If we want to properly unload images in Exit() the memory should always be
allocated in the same way. As we allocate memory when reading from file we
should do the same when the original image is in memory.
A further patch will be needed to free the memory when Exit() is called.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
All options have been moved to Kconfig and there is no need to have
board header files. Mini configurations require them that's why they are
still there.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPD autodetection hasn't been enabled that's why there is zero size
difference if that options are enabled/disabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace SDHCI controller listing by Kconfig symbol to let SPL know that
this board is using multiple SDHCIs controllers.
Kconfig help message should explain why this is needed.
Origin symbols were used in full u-boot but with moving to distro boot
this was fixed already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.
zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.
DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
All these board have also eeprom enabled that's why it is also enabled
via defconfig.
There is also no need to have zc70x specific config file that's why also
remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Boards have only one controller enabled that's why move to DM_I2C is
easy.
Add also i2c alias for not to be shown as i2c bus -1 because alias
doesn't exist.
Config file points to MAC stored in eeprom but it is not listed that's
why I have added 24c08 part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds new mini target for versal.
This configuration is very minimal in size which runs
from OCM. It contains support for mtest which can be
used for running DDR memory tests.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds distro boot commands for qspi, ospi and mmc.
The distro boot commands now reads the script from flash offset
of 63.5MB for qspi and ospi and executes it. For mmc its same
as generic distro boot command. As either one of the qspi or ospi can
exist on hardware, defined a single distroboot command as xspi
that works for both.
Setup default location via script_offset_f to 63.5MB to match the most
xilinx reference boards for qspi, ospi for now.
512kB allocated space for script size (script_size_f) should be more
than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds distro boot commands for qspi, nand and nor.
The distro boot commands now reads the script from flash offset
of 15.75MB and executes it.
Setup default location via script_offset_f to 15.75MB to match the most
xilinx reference boards for qspi, nand and set the same using
script_offset_nor to 0xE2EC0000 for nor.
256kB allocated space for script size (script_size_f) should be more
than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds mini eMMC configuration which has only
emmc0 and emmc1 functionalities and can run from small
amount of memory. This is required for memory constraint
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq and ZynqMP are sharing similar code and there is no reason to do
code duplication. Move zynq_board_read_rom_ethaddr() to common file for
easier conversion to DM.
Use ZynqMP version that's why also add CONFIG_ZYNQ_EEPROM_BUS to Syzygy
which is only one Zynq board which is using this feature.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds distro boot commands for qspi and nand. The
distro boot commands now reads the script from flash offset
of 63.5MB and executes it.
Setup default location via script_offset_f to 63.5MB to match the most
xilinx reference boards. 512kB allocated space for script size
(script_size_f) should be more than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is doing two things.
1. Exchanging order of boot commands. distro_bootcmd is run first
followed by Xilinx boot command.
2. Remove CONFIG_BOOTCOMMAND from configs (and follow mainline) by
creating Xilinx distribution bootcommand and wiring it as the last
bootcommand.
QSPI, NAND distribution boot command will be added later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is a place holder for HII configuration routing protocol and
HII configuration access protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Allow for handling keyboard layout package in HII database protocol.
A package can be added or deleted in HII database protocol, but
we don't set 'current' keyboard layout as there is no driver that
requests a keyboard layout.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Allow for handling GUID package in HII database protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch provides enough implementation of the following protocols to
run EDKII's Shell.efi and UEFI SCT:
* EfiHiiDatabaseProtocol
* EfiHiiStringProtocol
Not implemented are:
* ExportPackageLists()
* RegisterPackageNotify()/UnregisterPackageNotify()
* SetKeyboardLayout() (i.e. *current* keyboard layout)
HII database protocol in this patch series can handle only:
* GUID package
* string package
* keyboard layout package
(The other packages, except Device path package, will be necessary
for interactive and graphical UI.)
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Remove duplicate definition o EFI_SIMPLE_FILE_SYSTEM_PROTOCOL_GUID.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
UTF-16 strings in our code should all be u16 *. Fix an inconsistency for
file names which may lead to a warning for printf("%ls", ).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Refactor the switch from supervisor to hypervisor to a new function called
at the beginning of do_bootefi().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The SetVariable() runtime service does not change the data passed to it.
So mark the parameter as constant.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The runtime variable services never change GUIDs. So we should declare
the GUID parameters as constant.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The function, efi_init_obj_list(), can be shared in different pseudo efi
applications, like bootefi/bootmgr as well as my efishell. Moreover, it
will be utilized to extend efi initialization, for example, my "removable
disk support" patch and "capsule-on-disk support" patch in the future.
So with this patch, it will be moved to a new file, efi_setup.c, under
lib/efi_loader and exported, making no changes in functionality.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Remove lines deactivated by #if 1 #else
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We use u16* for Unicode strings and efi_uintn_t for UINTN. Correct the
signature of efi_exit() and efi_start_image().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The aim of this patch is not to have temporary variables used in
distro_bootcmd left as environment variables after run something.
See the discussion[1].
Without this patch, saveenv command also saves those variables, too.
While they are apparently safe, scsi_need_init can be harmful.
Please note that, in most cases, a variable should be converted to
hush's local variable, while "devplist" cannot because it is created
by "part" command as an environment variable.
[1] https://lists.denx.de/pipermail/u-boot/2018-December/350209.html
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Some boards support NVME drives. We should be able to use them as boot
devices.
NVME access requires running 'nvme scan'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add u16_strcpy() and u16_strdup(). The latter function will be
used later in implementing efi HII database protocol.
Signed-off-by: Akashi Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 393fccdf6c73 ("efi_loader: efi_guid_t must be 64-bit aligned")
has changed the alignment of efi_guid_t. This changed the size of
struct efi_configuration_table on 32-bit systems form 20 to 24 bytes. As
an array of this type is pointed to by the system table this breaks
compatibility with existing versions of GRUB and Linux. Let's get back the
original size by using the attribute __packed.
Fixes: 393fccdf6c73 ("efi_loader: efi_guid_t must be 64-bit aligned")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The UEFI Specification Version 2.7 Errata A defines:
"EFI_GUID
128-bit buffer containing a unique identifier value.
Unless otherwise specified, aligned on a 64-bit boundary."
Before this patch efi_guid_t was 8-bit aligned.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Common sound support
buildman environment support
of-platdata documentation improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlxf7igRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYKfggApQiL0Gv6NdGAQN+zfpjKY5a2QyjKsAxa
KLm3q8XyXIQXufMWOEPoW1iWm0iixpIFgChy8ff3m/OPDzsx99UXDTyvjitsSxtQ
5tFu8K78nUZT6OOE3HNhhlyW/xK442oKBzGt4MUt3kUZOELsCNuftgbJUWksHuO3
6pPrgt36E0uRGbUA4ioYCU336viJRPOOCdqb8hHViEihFj/IEv5T82RdE5y97YxG
dT7BZxjPkBH5ZN1uD/tdxG1k6IZBagZiYoDAsYp4YqNwmVsm5sLrZ9QVSf7EcH/y
qX8butZesiMd7xm7RROlrIImh7fb36N3zsoRiUWZDo1Al3IRkmZyVA==
=tdut
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10feb19' of git://git.denx.de/u-boot-dm
Samsung sound patches (applied for Samsung maintainer)
Common sound support
buildman environment support
of-platdata documentation improvements
regulator_set_enable() api throws an error in the following three cases:
- when requested to disable an always-on regulator
- when set_enable() ops not provided by regulator driver
- when enabling is actually failed.(Error returned by the regulator driver)
Sometimes consumer drivers doesn't want to track the first two scenarios
and just need to worry about the case where enabling is actually failed.
But it is also a good practice to have an error value returned in the
first two cases.
So introduce an api regulator_set_enable_if_allowed() which ignores the
first two error cases and returns an error as given by regulator driver.
Consumer drivers can use this api need not worry about the first two
error conditions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This enum still exists but we can shrink it a little based on recent
driver-model conversions with samsung. Update it to remove unused items.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
At present the model is shown twice, once in the generic code and once
in the exynos code. Drop the latter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
This converts the following to Kconfig:
CONFIG_BOARD_TYPES
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Bootm will fail to load kernels over 8MB, this is not enough
for our 64bit kernel images. Increase this to 64MB.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.
This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The board_r init function was complaining that we are looping through
an array, calling all our tiny init stubs sequentially via indirect
function calls (which can't be speculated, so they are slow).
The solution to that is pretty easy though. All we need to do is inline
the function that loops through the functions and the compiler will
automatically convert almost all indirect calls into direct inlined code.
With this patch, the overall code size drops (by 40 bytes on riscv64)
and boot time should become measurably faster for every target.
Signed-off-by: Alexander Graf <agraf@suse.de>
- Add st,digbypass on clk_hse node (needed for board rev.C)
- MLAHB/AHB max frequency increased from 200 to 209MHz, with:
- PLL3P set to 208.8MHz for MCU sub-system
- PLL3Q set to 24.57MHz for 48kHz SAI/SPI2S
- PLL3R set to 11.29MHz for 44.1kHz SAI/SPI2S
- PLL4P set to 99MHz for SDMMC and SPDIFRX
- PLL4Q set to 74.25MHz for EVAL board
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The content between these guards was removed in commit 9baa2bce28
("Removed unused references to CONFIG_SERIALx"). Remove the now
empty #ifdef/#endif block and the accompanying comment.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Memory functions may have architecture specific implementations. These
should be tested.
Provide unit tests for memset(), memcpy(), memmove().
Provide a 'ut lib' sub-command to execute the tests.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is wrapper for calling of_alias_get_highest_id() when live tree is
enabled and fdtdec_get_alias_highest_id() if not.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Find out the highest alias ID used for certain subsystem.
This call will be used for alocating IDs for i2c buses which are not
described in DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The same functionality was added to Linux for i2c bus registration with this
commit message:
"
of: base: add function to get highest id of an alias stem
I2C supports adding adapters using either a dynamic or fixed id. The
latter is provided by aliases in the DT case. To prevent id collisions
of those two types, install this function which gives us the highest
fixed id, so we can then let the dynamically created ones come after
this highest number.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
"
Add it also to U-Boot for DM I2C support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
SF_DUAL_FLASH claims to enable support for SF_DUAL_STACKED_FLASH and
SF_DUAL_PARALLEL_FLASH. But, in current U-Boot code, grepping for above
enums yield no user and therefore support seems to be incomplete. Remove
these configs so as to avoid confusion.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD
layer. Fix up sf_dataflash to work in legacy way. And update sandbox to
use new interfaces/definitions
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
