Store the environment in eMMC, at the end of the second boot sector.
This should not conflict with any other eMMC usage: U-Boot is stored
well below this location, and the kernel only uses the general area
of the eMMC once booted, not the boot sectors.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This allows MMC drivers to perform cache flusing on the bufffers
without issue.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a device tree for Ventana; the Seaboard file no longer represents
the HW present on Ventana.
Enable USB on Ventana.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The SMSC95xx series may exist either directly on a main board, or as a USB
to Ethernet dongle. However, dongles containing these chips are very rare.
Hence, remove this config option, except on Harmony where such a chip is
actually present on the board.
The asix option remains, since it's a popular chip, and I actively use a
dongle containing this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Override -march setting for tegra to -march=armv4t for files that are
necessary for low level init on tegra.
The recent change to use -march=armv7-a for armv7 caused a regression
on tegra because tegra starts boot on a arm7tdmi processor before
transferring control to the cortex-a9. While still executing on the
arm7tdmi there are calls to getenv_ulong() and memset() that cause an
illegal instruction exception if compiled for armv7.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Correct this warning seen by Albert:
ap20.c:44:18: warning: array subscript is above array bounds
There is a subtle bug here which currently causes no errors, but might
in future if people use PCI or the 32KHz clock. So take the opportunity
to correct the logic now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
... to enable USB host support, which enables Ethernet support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
... to enable USB host support, which enables Ethernet support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is based on top of:
tegra: add alternate UART1 funcmux entry
tegra: add UART1 on GPU funcmux entry
v2: remove enum change
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Tom Warren <twarren@nvidia.com>
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
CONFIG_CMD_PING/NFS aren't required for Whistler to boot.
Add some comments.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This implements a useful bootcmd for Tegra. The boot order is:
* If USB enabled, USB storage
* Internal MMC (SD card or eMMC)
* If networking is enabled, BOOTP/TFTP
When booting from USB or MMC, the boot script is assumed to be in
partition 1 (although this may be overridden via the rootpart variable),
both ext2 and FAT filesystems are supported, the boot script may exist
in either / or /boot, and the boot script may be named boot.scr.uimg or
boot.scr.
When booting over the network, it is assumed that boot.scr.uimg exists
on the TFTP server. There is less flexibility here since those setting
up network booting are expected to need less hand-holding.
In all cases, it is expected that the initial file loaded is a U-Boot
image containing a script that will load the kernel, load any required
initrd, load any required DTB, and finally bootm the kernel.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
console isn't used by anything, and the kernel should be set appropriately
by whatever script is booting the kernel, not imposed by the bootloader.
mem might be useful, but the current value is pretty bogus, since it
includes nvmem options that make no sense for an upstream kernel, and
equally should not be required for any downstream kernel. Either way, this
is also best left to the kernel boot script.
smpflag isn't used by anything, and again was probably intended to be a
kernel command-line option better set by the kernel boot script.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:
E1120 motherboard
E1108 CPU board
E1116 PMU board
The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.
Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
(In at least some configurations) Whistler uses UART1 on pingroups
UAA, UAB.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass's proposal to fix this on Seaboard was NAK'd, so I
removed his NS16550 references and added a small delay before
SPI/UART muxing. Tested on my Seaboard with large SPI reads/writes
and saw no corruption (crc's matched) and no spurious comm chars.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jimmy Zhang <jimmzhang@nvidia.com>
Use the POSIX variant of basename due to BSD systems (e.g. OS X) do not provide
GNU version of basename(3). It is save to use the POSIX variant here cause we do
never use argv[0] later on which may be modified by the basename(3) POSIX
variant.
On systems providing GNU variant the GNU variant should be used since string.h
is included before libgen.h. Therefore let the _GNU_SOURCE as is.
This patch fixes following warning (on OS X):
---8<---
mkenvimage.c: In function ‘main’:
mkenvimage.c:105: warning: implicit declaration of function ‘basename’
mkenvimage.c:105: warning: assignment makes pointer from integer without a cast
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Keith Mok <ek9852@gmail.com>
The value of ET0_ERXD6 and GPSR1_INIT was wrong.
This fixes them.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch dramatically drops the amount of time u-boot needs to read a
file from an ext2 partition. On a typical 2 to 5 MB file (kernels and
initrds) it goes from tens of seconds to a couple seconds.
All we are doing here is grouping contiguous blocks into one read.
Boot tested on Globalscale Technologies Dreamplug (Kirkwood ARM SoC)
with three different files. sha1sums were calculated in Linux
userspace, and then confirmed after ext2load.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Add a new command "sysboot" which parses syslinux menu files and boots
using kernel and initrd specified by menu files. The operation is similar
to "pxe boot" except local files on ext2 or fat filesystem are parsed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
For syslinux, the initrd can be set in the append string as
"initrd=<file>", so try to find it there if we haven't already set the
initrd.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
If the file path starts with a '/', then don't pre-pend the bootfile path.
This fixes a problem with running 'pxe boot' multiple times where the
bootfile path gets pre-pended to itself each time.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Kernels can be specified using "linux" or "kernel" entry. The difference
is kernel is supposed to detect the type of file, but for u-boot both are
treated the same.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Make the menu timeout apply only when prompt flag is set and after the
menu is displayed. This allows auto boot to work no matter whether prompt
is set or cleared. Use the default selection if the menu times out.
This also fixes the timeout value given to readline_into_buffer to be
seconds instead of 10th of seconds.
Old behavior:
if prompt
display menu and wait for choice
else
wait for timeout
if key pressed
display menu and wait for choice
else
exit command
New behavior:
if prompt
display menu
if key pressed
wait for choice
else
boot default entry on timeout
else
boot default entry
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file. This is used when a board has not set its
own table.
Signed-off-by: Tom Rini <trini@ti.com>
patman shouts when it couldn't find a $(HOME)/.patman file.
Handle it in a sane way by creating a new one for the user.
It looks for a user.name and user.email in the global .gitconfig
file, waits for the user input if it can't find there. Update the
same in the README
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Move the config file from ~/.config/patman to ~/.patman as it is
more appropriate to have it there. Update the same in the README.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Compressing the logos with lzma rather than gzip saves ~9kb with the
Blackfin 24bit images and ~3kb with the 16bit images.
Add a new -l option to easylogo so people can pick lzma as their
decompression routine.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Simplify the code slightly by using a for() loop since this is
basically what we're already doing -- incrementing "ngood" to
the value in "count".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Not only does the source code get simpler, but it also shrinks the
compiled object code too.
While we're here, tweak the summary message to avoid the plural
issue. It isn't that big of a deal, and it's currently wrong
anyways in the single (1 byte) case:
Total of 1 byte were the same
Grammar wise, that should be "was" rather than "were". The new
output people should be able to easily figure out:
Total of 1 byte(s) were the same
Total of 10 byte(s) were the same
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-mpc83xx:
km/common: check test_bank and testpin for testboot
powerpc/83xx/km: readout dip_switch on kmcoge5ne
powerpc/83xx: configure CONFIG_POST for kmcoge5ne
powerpc/83xx/km: added missing enable of application buffer
km/common: increase bootlimit to 3
km/common: fixed error in ethaddr (1-byte-shift)
MAINTAINERS: cleanup for keymile boards
powerpc/83xx: add kmcoge5ne board support
km/common: add support for second flash
powerpc83xx/km: remove unneeded CONFIG_PCI for kmeter1
powerpc83xx/km: lock the window size to 2GiB befor fixing sdram size
powerpc/83xx/km: use tuxx1.h for kmsupx5 target
powerpc/83xx: increment malloc heap size for the MPC832x MDS boards
Signed-off-by: Wolfgang Denk <wd@denx.de>
If the testpin is asserted, first check if a test_bank
variable is defined before trying to boot this
test_bank.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
On kmcoge5ne we have a dip switch present. If this switch
was switched on the actual_bank is set to 0 and this SW
will be booted.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
kmcoge5ne starts the post tests if the testpin on
the board was enabled. Currently it does simply a memory
test.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Enabled application buffers in uboot to allow application chipselect
access in uboot.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
