Currently, on imx6sabresd and gwventana boards, the company logo
and U-Boot logo are shown.
The correct behavior is to show only the company logo, if available,
and not both logos.
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com> #gw_ventana
commit 7c84319af9c7 ("dm: gpio: Correct use of -ENODEV in drivers")
changed the return code for an I2C NAK from -ENODEV to -EREMOTEIO.
Update the gsc_i2c_read and gsc_i2c_write functions for this change
to properly retry the transaction on a NAK meaning the GSC is busy.
Fixes: 7c84319af9 ("dm: gpio: Correct use of -ENODEV in drivers")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The 2x256 MiB SF variant of this system has 192 MiB rootfs MTD partition
containing UBI on SF0, use the correct size in U-Boot environment, else
U-Boot cannot mount UBI and boot on this variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: Tom Rini <trini@konsulko.com>
Enable ONFI detection to fix NAND chip configuration. Without this
the NAND oobsize will be wrong which leads to invalid ECC strength and
incompatibility with the previous configuration.
Fixes: 777f333c37 ("imx: ventana: enable dm for MTD and NAND")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Previous u-boot code changed the default bch setting behavior and caused
backward compatible issue. This fix choose the legacy bch geometry back
again as the default option. If the minimum ecc strength that NAND chips
required need to be chosen, it can be enabled by either adding DT flag
"fsl,use-minimum-ecc" or CONFIG_NAND_MXS_USE_MINIMUM_ECC in configs. The
unused flag "fsl,legacy-bch-geometry" get removed.
Fixes: 51cdf83eea (mtd: gpmi: provide the option to use legacy bch geometry)
Fixes: 616f03daba (mtd: gpmi: change the BCH layout setting for large oob NAND)
Tested-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
The code was mistakenly initializing the input buffer twice.
Tested to be working on BeagleBone by adjusting CONFIG_SYS_BOOTM_LEN to
64MiB (probably works with less) and preparing uImage with:
cat arch/arm/boot/Image \
| zstd --ultra -22 --zstd=windowLog=22 \
> linux.bin.zst
mkimage -A arm -T kernel uImage -C zstd -d linux.bin.zst \
-a 0x80008000 -e 0x80008000
Without the windowLog restriction, bootm fails with a zstd decompression
error 7 (window too large), which I haven't troubleshooted.
There should be a bit more documentation on the feature...
Reviewed-by: Simon Glass <sjg@chromium.org>
Fixes: 458b30af66 image: Update image_decomp() to avoid ifdefs
make sandbox_defconfig
make mrproper
make tests
fails with
../drivers/video/u_boot_logo.S: Assembler messages:
../drivers/video/u_boot_logo.S:5: Error: file not found: drivers/video/u_boot_logo.bmp
We have to delete the generated file.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current approach for setting the environment variables that
describe the memory layout runs the risk of overlapping with
reserved memory regions. Use the lmb code to derive the addresses
for these variables instead.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The firmware on larger NVMe drives needs more than 100ms to come up.
Change the timeout to 1s.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documentation:
* man-page for the wdt command
UEFI:
* Unit test for boot manager
-----BEGIN PGP SIGNATURE-----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=n5MM
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc5-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc5-2
Documentation:
* man-page for the wdt command
UEFI:
* Unit test for boot manager
When calling efi_dp_from_name() we are not interested in the device part.
Just pass NULL as an argument.
Suggested-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Provide a unit test for
* efidebug boot add
* efidebug boot order
* bootefi bootmgr
* initrd via EFI_LOAD_FILE2_PROTOCOL
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Up to now the initrddump.efi application has drained the input after
showing the prompt. This works for humans but leads to problems when
automating testing. If the input is drained, this should be done before
showing the prompt.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
initrddump.efi uses colored output and clear the screen. This is not
helpful for integration into Python tests. Allow specifying 'nocolor' in
the load option data to suppress color output and clearing the screen.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Commit f11513d997 ("net: phy: realtek: Add tx/rx delay config for
8211e") made the Realtek PHY driver honour the phy-mode DT property,
to set up the proper delay scheme for the RX and TX lines. A similar
change in the kernel revealed that those properties were mostly wrong.
The kernel DTs got updated over the last few months, but we were missing
out on the U-Boot version.
Just sync in the phy-mode properties from the mainline kernel,
v5.17-rc7, to avoid the breaking DT sync that late in the cycle.
This fixes Ethernet operation on the affected boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Commit 5bc4cd05d7 ("sunxi: move non-essential code out of s_init()")
moved the call to eth_init_board() from s_init() into board_init_f().
This means it's now only called from the SPL, which makes sense for
most of the other moved low-level functions. However the GMAC pinmux and
clock setup in eth_init_board() was not happy about that, so it broke
the sun7i GMAC.
Since Ethernet is of no use in the SPL anyway, just move the call into
board_init(), which is only run in U-Boot proper.
This fixes Ethernet operation for the A20 SoCs, which broke in
v2022.04-rc1, with the above mentioned commit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Petr Štetiar <ynezz@true.cz> [a20-olinuxino-lime2]
Commit 0934dddc64 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke SPI support on some Espressobin boards and results in
following U-Boot error:
Loading Environment from SPIFlash... jedec_spi_nor flash@0: unrecognized JEDEC id bytes: f7, 30, 0b
*** Warning - spi_flash_probe_bus_cs() failed, using default environment
Before that commit DT node for SPI was called 'spi-flash@0' and after
that commit it is called 'flash@0'. Before that commit 'spi-max-frequency'
was set to 50000000 and after it is 104000000.
Rename DT node 'spi-flash@0 in armada-3720-espressobin-u-boot.dtsi to
'flash@0' and set custom U-Boot 'spi-max-frequency' back to 50000000.
With this change SPI is working on Espressobin again and it is detected
with JEDEC ids ef, 60, 16 on our tested unit.
Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
Note that it is unknown why spi-max-frequency with value 104000000 does not
work in U-Boot as it works fine with Linux kernel. Also note that in
defconfig file configs/mvebu_espressobin-88f3720_defconfig is set option
CONFIG_SF_DEFAULT_SPEED=40000000 which is different value than in DT.
Fixes: 0934dddc64 ("arm: a37xx: Update DTS files to version from upstream Linux kernel")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
i2c changes for fixes-for-2022.04
- atsha204a-i2c.c
DTS and I2C fixes for Atmel ATSHA204 from Adrian
- i2c: fix always-true condition in i2c_probe_chip()
from Nikita
- eeprom: Do not rewrite EEPROM I2C bus with DM I2C enabled
from Marek
- clarify bootcount documentation fix from Michael
Commit 0934dddc64 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke USB port on Turris MOX, because in Linux' DTS the bus
voltage supply is described as a `phy-supply` property of connector
node, a mechanism that is not supported in U-Boot yet.
For now, fix this by adding `vbus-supply` to usb3 node.
Fixes: 0934dddc64 ("arm: a37xx: Update DTS files to version from upstream Linux kernel")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
With DM I2C, the EEPROM bus has been correctly configured in
eeprom_execute_command() already. Do not reconfigure it here
with hard-coded bus number again.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch replaces use fdtdec_get_addr with simpler dev_read_addr().
fdtdec_get_addr doesn't work properly on ZynqMP-based (64bit) system. Although
not confirmed, it could be related to the fact, that quoting the documentation,
"This variant hard-codes the number of cells used to represent the address and
size based on sizeof(fdt_addr_t) and sizeof(fdt_size_t)".
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Once request is sent, and before receiving a response, the delay is required.
This patch fixes missing delay for before first response try.
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
If the maximum number of wake-up attempts is exceeded, return -ETIMEDOUT.
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Documentation:
* Fix documentation of FIP creation for Amlogic boards
* Update Nokia RX-51 QEMU documentation
* Add Raspberry Pi documentation
UEFI:
* Fix booting via short form device paths
* Support short form device paths in 'efidebug boot add'
* Fix ESP detection for capsule updates
* Allow ACPI table usage even if device-tree exists - ignore DT
* OP-TEE based GetVariable(): return attributes when buffer too small
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmI3UAIACgkQxIHbvCwF
GsRopA/7BLiFUFayMnVL3qCLZKrceKSbz76zSs18zMab4U7FWEiWTLfqhV4PSgT+
SfcpOCFsodRIGvNKwm/RpVSpwj7NPINUL29Hn70ojN0ckuJZNBj8ILflr7y6iuCX
OI48rezhvnOMKk0F2JNFCQDzPYJVKm7Ej1M+CfVCuL+iQNEk4l9FI/pgnT8at5D/
TcmUQIvqEj6wTv2XaT59AKm85R0r14NJHNRgNEEwgeReiZZ/cxK9I/jYTMFxWK0r
uOEB1jrsRKnTMq3fgg9fOZRQvjavqoqe0evVtBfrkBpYP48AK9c9vXSBfCSUnygl
lM+JS6keWaKeOH4605UHhxaFjAoW7VEH+a6jubbDoNNTUspRGpY6UViAc7O16DDK
AjZN6uoUkeREFMokvHsgsh63cRj2WkKnildAIcnRyLhqQuHe+QS8ndiOSV4Q0peO
ifT8BFF4loN2ttAViKNYeM6ydBabjmwJiuzuUG0tyxiYDXLS0/ErNp7aUwTgc/qP
1E46PS+f6sZG2oiNk5L2MP689wEBgZpjSck4aH3ba+UrtGXSh/YC5ERaN1Zm7K5M
GJ3UOL+G+o0Is4gYgp7tvizVfu+8FIC/ilOndmgtwdRoUYrUA2ePx7WPvArnHLc3
rymR7IJ1yCD5RjVB3lA6eL76ORKNRBe3Gs7zGRK5jg55pw3MFSo=
=Kn/h
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc5
Documentation:
* Fix documentation of FIP creation for Amlogic boards
* Update Nokia RX-51 QEMU documentation
* Add Raspberry Pi documentation
UEFI:
* Fix booting via short form device paths
* Support short form device paths in 'efidebug boot add'
* Fix ESP detection for capsule updates
* Allow ACPI table usage even if device-tree exists - ignore DT
* OP-TEE based GetVariable(): return attributes when buffer too small
The tools dtbdump.efi and initrddump.efi are useful for Python testing even
if CONFIG_EFI_SELFTEST=n.
Don't clear the screen as it is incompatible with Python testing.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The block IO protocol may be installed on any handle. We should make
no assumption about the structure the handle points to.
efi_disk_is_system_part() makes an illegal widening cast from a handle
to a struct efi_disk_obj. Remove the function.
Fixes: Fixes: 41fd506842 ("efi_loader: disk: add efi_disk_is_system_part()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The GUID of partitions is sufficient for identification and will stay
constant in the lifetime of a boot option. The preceding path of the
device-path may change due to changes in the enumeration of devices.
Therefore it is preferable to use the short-form of device-paths in load
options. Adjust the 'efidebug boot add' command accordingly.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The boot manager must support loading from boot options using a short-form
device-path, e.g. one where the first element is a hard drive media path.
See '3.1.2 Load Options Processing' in UEFI specification version 2.9.
Fixes: 0e074d1239 ("efi_loader: carve out efi_load_image_from_file()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Let function efi_dp_find_obj() additionally check if a given protocol is
installed on the handle relating to the device-path.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
efi_dp_find_obj() should not return any handle with a partially matching
device path but the handle with the maximum matching device path.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Starting UEFI Spec 2.8 we must fill in the variable attributes when
GetVariable() returns EFI_BUFFER_TOO_SMALL and Attributes is non-NULL.
This code was written with 2.7 in mind so let's move the code around a
bit and fill in the attributes EFI_BUFFER_TOO_SMALL is returned
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For targets that enable ACPI, we should not pass Device Trees into
the payload. However, our distro boot logic always passes the builtin
DT as an argument.
To make it easy to use ACPI with distro boot, let's just ignore the DT
argument to bootefi when ACPI is enabled. That way, we can successfully
distro boot payloads on ACPI enabled targets.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add documentation about the different configuration files for the
RaspberryPi board family.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
There is no CONFIG_UEFI_SECURE_BOOT, and there was never any.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add section how to run U-Boot in n900 qemu machine.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
It add documentation on licencing & provides links to the amlogic-boot-fip
pre-built files collections.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
