Commit graph

127 commits

Author SHA1 Message Date
Ilya Yanok
7ac2fe2da2 OMAP: networking support for SPL
This patch adds support for networking in SPL. Some devices are
capable of loading SPL via network so it makes sense to load the
main U-Boot binary via network too. This patch tries to use
existing network code as much as possible. Unfortunately, it depends
on environment which in turn depends on other code so SPL size
is increased significantly. No effort was done to decouple network
code and environment so far.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-01 10:02:14 -07:00
Tom Rini
a4a99fffd8 am335x evm: Enable support for spi0
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:19 +02:00
Tom Rini
6bfca5031b am335x evm: Enable MMC1 pinmux
MMC1 is available in profile 2 on the GP EVM and is exposed on the
expansion header on beaglebone.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:18 +02:00
Tom Rini
036fd65a8c am335x evm: Initial support for AM335x GP EVM Profiles
The AM335x GP EVM can have one of 8 different profiles selected.  Each
profile has a different set of peripherals and requires different pinmux
configurations that conflict with other profiles.  i2c1 is an example of
a conflicted mux currently.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:18 +02:00
Tom Rini
db7dd8109c am33xx: Rework pinmux functions
- Move definition of the EEPROM contents to <asm/arch/sys_proto.h>
  - Make some defines a little less generic now.
- Pinmux must be done by done by SPL now.
- Create 3 pinmux functions, uart0, i2c0 and board.
- Add pinmux specific to Starter Kit EVM for MMC now.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
65d750be59 am33xx: Add support for TI AM335x StarterKit EVM
- Board requires gpio0 #7 to be set to power DDR3.
- Board uses DDR3, add a way to determine which DDR type to call
  config_ddr with.
- Both of the above require filling in the header structure early, move
  it into the data section.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
973b663820 am33xx: Remove board/ti/am335x/evm.c
The intention has always been (and boards are to support) an i2c EEPROM
that will identify what hardware they are, allowing a single binary to
support multiple boards.  As such, remove the 'evm.c' file as there is
nothing EVM centric in it currently, only SoC peripheral configuration.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Chandan Nath
9304296044 am335x_evm: CPSW support
This patch adds board-specific initialization for CPSW on
TI AM335X based boards. Tested on BeagleBone.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split board-specific part into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:11 +02:00
Ilya Yanok
c59a6a0dac am335x_evm: read the on-board EEPROM
Read the on-board EEPROM during startup to detect the version
of the board we are running on (as for now only BeagleBone vs
EVM detection is supported).

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:11 +02:00
Chandan Nath
89017e150e am33xx: pin mux defintions for CPSW switch
This patch adds pin mux settings for CPSW switch found on
TI AM335X based boards (MII and RGMII modes).

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split pinmux into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:11 +02:00
Peter Meerwald
2c30c18487 beagle: only call DSS code when #defined CONFIG_VIDEO_OMAP3
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-09-01 14:58:10 +02:00
Steve Sakoman
d3decdebde omap: am335x_evm: enable i2c1 channel
This patch sets up pinmux, enables fclk, and
defines CONFIG_I2C_MULTI_BUS

Signed-off-by: Steve Sakoman <steve@sakoman.com>
2012-09-01 14:58:10 +02:00
Peter Meerwald
71a271c654 beagle: removed unused pr_debug #define
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
2012-09-01 14:58:10 +02:00
Peter Meerwald
fff1a57208 beagle: make get_expansion_id(), get_board_revision(), beagle_display_init() static
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-09-01 14:58:10 +02:00
Steve Sakoman
28adc91a28 omap: am335x_evm: remove unused definitions
UART_RESET, UART_CLK_RUNNING_MASK, and UART_SMART_IDLE_EN
are defined inn evm.c but not used. Also removes unnecessary
include of serial.h

PHYS_DRAM_1_SIZE is defined in am335x_evm.h but never used.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
2012-09-01 14:58:09 +02:00
Wolfgang Denk
b98b611502 Merge branch 'next' of git://git.denx.de/u-boot
* 'next' of git://git.denx.de/u-boot:
  MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
  doc: cleanup - move board READMEs into respective board directories
  net: sh_eth: add support for SH7757's GETHER
  net: sh_eth: modify the definitions of regsiter
  net: sh_eth: add SH_ETH_TYPE_ condition
  net: sh_eth: clean up for the SH7757's code
  net: fec_mxc: Fix MDC for xMII
  net: fec_mxc: Fix setting of RCR for xMII
  net: nfs: make NFS_TIMEOUT configurable
  net: Inline the new eth_setenv_enetaddr_by_index function
  net: allow setting env enetaddr from net device setting
  net/designware: Consecutive writes to the same register to be avoided
  CACHE: net: asix: Fix asix driver to work with data cache on
  net: phy: micrel: make ksz9021 phy accessible
  net: abort network initialization if the PHY driver fails
  phylib: phy_startup() should return an error code on failure
  net: tftp: fix type of block arg to store_block

Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-07-30 20:39:52 +02:00
Wolfgang Denk
702e6014f1 doc: cleanup - move board READMEs into respective board directories
Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2012-07-29 15:42:02 +02:00
SRICHARAN R
d2ebaa41ed ARM: OMAP4: PANDA: Add rest of the USB module pads to essentials
In commit 1a89a217f5 we moved most of the
required pads and mux data for USB to the essential list so that later
on we could NOT enable anything that wasn't essential unless otherwise
configured.  This was however missing a few pandaboard-specific parts
which left for example USB ethernet non-functional.

Tested this on OMAP4430 ES2.2, OMAP4460 ES1.1 PANDA boards.

(Reworded by Tom Rini to be more precise about what the problem was)

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Tested-by: Tom Rini <trini@ti.com>
2012-07-20 14:24:08 +02:00
Peter Meerwald
ef88e60902 beagle: add eeprom expansion board info for bct brettl4
this is for a prototyping board

vendor/product ids have been added to
http://elinux.org/BeagleBoardPinMux#List_of_Vendor_and_Device_IDs

Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-07-09 22:44:32 +02:00
SRICHARAN R
1a89a217f5 ARM: OMAP4/5: Move USB pads to essential list.
USB module pads are getting enabled under non-essential
group. These will be required for fastboot, tftp support.
So move this to essential list to have them working when
non-essential pads are no more muxed.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07 14:07:36 +02:00
Tom Rini
2ab2810375 am33xx: Do not call init_timer twice
We do not need to call init_timer both in SPL and U-Boot itself, just
SPL needs to initialize the timer.

Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07 14:07:21 +02:00
Tero Kristo
954211cb8c omap4: panda: disable uart2 pads during boot
If uart2 is enabled during boot, spurious wifi chip transmission will
hang the module and it is impossible to recover from this situation
without hard reset. This will prevent any l4_per domain idle
transitions.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
2012-05-15 08:31:40 +02:00
Tom Rini
60bd10df8a omap730p2: Remove empty misc_init_r
We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R

Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:27 +02:00
Tom Rini
b8f4a728e6 omap5912osk: Remove empty misc_init_r
We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R

Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:27 +02:00
SRICHARAN R
2114429896 power: twl6035: add palmas PMIC support
palmas/TWL6035 is power IC for omap5 evm boards

Signed-off-by: Balaji T K <balajitk@ti.com>
2012-05-15 08:31:25 +02:00
SRICHARAN R
84b16af29f OMAP5: board: Add pinmux data for omap5_evm board.
Adding the full pinmux data for OMAP5430 sevm board.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15 08:31:23 +02:00
Nishanth Menon
3acb553439 OMAP4460: TPS Ensure SET1 is selected after voltage configuration
TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
                           |---------------| (SET1 default 1.4V)
                           |               --------(programmed voltage)
                           | <- (This switch happens on mux7,pullup)
vdd_mpu(TPS)         -----/ (OPP boot voltage)
                                             --------- (programmed voltage)
vdd_core(TWL6030)    -----------------------/ (OPP boot voltage)
Problem 1)                |<----- Tx ------>|
   timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.

By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
                                  -------- (programmed voltage)
vdd_mpu(TPS)         ------------/ (Opp boot voltage)
                                   --------- (programmed voltage)
vdd_core(TWL6030)    -------------/ (OPP boot voltage)

NOTE: This does not attempt to address OMAP5 - Aneesh please confirm

Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2012-05-15 08:31:22 +02:00
Jonathan Solnit
bbbc1ae921 ARM:OMAP+:MMC: Add parameters to MMC init
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency.  While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board.  The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.

Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
2012-05-15 08:31:22 +02:00
Joel Fernandes
aae58b954b BeagleBoard: Remove userbutton command and use gpio command instead
Remove userbutton command and do the detection in board config file using the gpio command

Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2012-04-16 14:47:58 +02:00
Tom Rini
76e2c169a5 OMAP: Remove omap1610inn-based boards
The CS_AUTOBOOT configurations have been broken for a long time.
Kshitij Gupta is no longer at TI making these broken and orphaned
boards, so remove.

Signed-off-by: Tom Rini <trini@ti.com>
2012-03-29 08:19:29 +02:00
Anatolij Gustschin
3fbc6931a4 board/ti/beagle/beagle.c: Fix build warnings
Fix:
beagle.c:257:13: warning: function declaration isn't a prototype
[-Wstrict-prototypes]
beagle.c:257:13: warning: function declaration isn't a prototype
[-Wstrict-prototypes]

Also make beagle_dvi_pup() checkpatch clean, fix:
ERROR: open brace '{' following function declarations go on the
next line

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
2012-03-29 08:19:29 +02:00
Simon Glass
578ac1e9ba bootstage: Make use of BOOTSTAGE_ID_RUN_OS in show_boot_progress()
This changes the number 15 as used in boot_stage_progress() to use the
new name provided for it. This is a separate patch because it touches
so many files.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-03-18 20:45:57 +01:00
Peter Meerwald
4258aa62fb beagle: enable DVI_PUP
this patch addresses the issue that there is no DVI output on beagleboard-xm in
u-boot; the TFP410 is not powered on, DVI_PUP needs to be set high

this is done differently on beagleboard-xm rev. B/C versus earlier boards:
beagleboard-xm B/C need to set GPIO2 of the TWL4030
earlier boards need to set GPIO170

note that the change occured somewhere inbetween beagleboard-xm rev. A2 and A3

note that beagleboard-xm rev. A and rev. B cannot be distinguished using
get_board_revision(), REVISION_XM_A/REVISION_XM_B is bogus

due to this glitch, the patch cannot work correctly on some beagleboard-xm
rev A/B boards

tested on beagleboard-xm rev. C (you should see orange color on a monitor)

note that the framebuffer is NOT yet set up, this could be done along the
lines below (for 800x480 resolution and RGB24) before calling omap3_dss_enable()

static void configure_frame_buffer() {
	writel(0x80500000, (uint *) 0x48050480); // address
	writel(0x80500000, (uint *) 0x48050484);
	writel(0x01df031f, (uint *) 0x4805048c); // size
	writel(0x00000091, (uint *) 0x480504a0); // RGB24
}

Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-02-27 21:19:24 +01:00
Peter Meerwald
66327eb359 beagle: fix typos
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-02-12 10:11:32 +01:00
Govindraj.R
49be71c475 OMAP4: ehci-omap: enable ehci-omap for panda boards
For panda initialise the mux pins for ehci usage and
enable ehci in omap4_panda config file.

Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Stefano Babic <sbabic@denx.de>
2012-02-12 10:11:31 +01:00
Govindraj.R
43b62393da ehci-omap: Clean up added ehci-omap.c
Clean up added ehci-omap.c and make it generic for re-use across
omap-soc having same ehci ip block. Also pass the modes to be configured
from board file and configure the ports accordingly. All usb layers
are not cache aligned, till then keep cache off for usb ops as ehci will use
internally dma for all usb ops.

* Add a generic common header ehci-omap.h having common ip block
  data and reg shifts.
* Rename and modify ehci-omap3 to ehci.h retain only conflicting
  sysc reg shifts remove others and move to common header file.
* pass the board data for beagle/panda accordinly to use
  ehci ports.

Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
2012-02-12 10:11:31 +01:00
Ilya Yanok
29321c0518 ehci-omap: driver for EHCI host on OMAP3
Taken from Beagle code. Tested on mcx board (AM3517-based).

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Tested-by: Stefano Babic <sbabic@denx.de>
2012-02-12 10:11:30 +01:00
robertcnelson@gmail.com
223b8aa42c Beagleboard: Correct memory size on rev C4
The logic for the rev C4 boards was missing one of the cases
(variant with Micron NAND and 2x128MB).

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
2012-02-12 10:11:23 +01:00
Patil, Rachna
b4116ede36 ARM: AM33XX: Add i2c support
Add i2c driver board hookup for AM335X EVM

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Patil, Rachna <rachna@ti.com>
2012-01-23 11:57:31 +01:00
Chandan Nath
8a8f084e4f ARM:AM33XX: Add SPL support for AM335X EVM
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:12 +01:00
Chandan Nath
876bdd6d46 ARM:AM33XX: Add mmc/sd support
This patch add supports for mmc/sd driver on AM335X platform.
PLL and pinmux configurations for mmc/sd are configured in this
patch.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:12 +01:00
Peter Meerwald
6cce55047c beagle: add eeprom expansion board info for bct brettl3
this is for a prototyping board

vendor/product ids have been added to
http://elinux.org/BeagleBoardPinMux#List_of_Vendor_and_Device_IDs
2012-01-16 08:40:10 +01:00
Chris Lalancette
df65a3fe35 omap4_panda: Initialize the USB phy
During misc_init_r, make sure to setup the clocks
properly for the USB hub on the pandaboard.  With
this in place, the USB hub and the ethernet works
on the pandaboard.

Signed-off-by: Chris Lalancette <clalancette@gmail.com>
Acked-by: Aneesh V <aneesh@ti.com>
2011-12-19 17:52:44 +01:00
Wolfgang Denk
6bef783310 board/ti/omap2420h4/omap2420h4.c: Fix GC 4.6 build warning
Fix:
omap2420h4.c: In function 'dram_init':
omap2420h4.c:196:25: warning: variable 'cpu' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Tom Rini <trini@ti.com>
2011-12-12 14:26:17 +01:00
Wolfgang Denk
f23b7ea0e6 board/ti/omap730p2/flash.c: Fix GCC 4.6 build warnings
Fix:
flash.c: In function 'flash_get_offsets':
flash.c:122:10: warning: variable 'pOrgDef' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'flash_erase':
flash.c:263:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:439:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dave Peverley <dpeverley@mpc-data.co.uk>
Acked-by: Tom Rini <trini@ti.com>
2011-12-10 23:12:40 +01:00
Wolfgang Denk
2ccf26da5e board/ti/omap1610inn/flash.c: Fix GCC 4.6 build warnings
Fix:
flash.c: In function 'flash_get_offsets':
flash.c:139:10: warning: variable 'pOrgDef' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'flash_erase':
flash.c:280:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:456:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Tom Rini <trini@ti.com>
2011-12-10 23:11:48 +01:00
Tom Rini
d067cc464f AM3517 CraneBoard: Add SPL support
The only change of note is that we move from 0x80008000 to 0x80100000
for CONFIG_SYS_TEXT_BASE

Cc: Nagendra T S <nagendra@mistralsolutions.com>
Tested-by: Koen Kooi <k-kooi@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:39 +01:00
Tom Rini
673283f3fc OMAP3: Add SPL support to omap3_evm
Add Hynix 200MHz timing information to <asm/arch-omap3/mem.h>.
This also changes CONFIG_SYS_TEXT_BASE to 0x80100000.

Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:38 +01:00
Tom Rini
75c57a3570 OMAP3: Add SPL support to Beagleboard
This introduces 200MHz Micron parts timing information based on x-loader
to <asm/arch-omap3/mem.h> and Numonyx MCFG calculation.  The memory init
logic is also based on what x-loader does in these cases.  Note that
while previously u-boot would be flashed in with SW ECC in this case it
now must be flashed with HW ECC.  We also change CONFIG_SYS_TEXT_BASE to
0x80100000.

Cc: Dirk Behme <dirk.behme@gmail.com>
Beagleboard rev C5, xM rev A:
Tested-by: Tom Rini <trini@ti.com>
Beagleboard xM rev C:
Tested-by: Matt Ranostay <mranostay@gmail.com>
Beagleboard rev B7, C2, xM rev B:
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:38 +01:00
Ilya Yanok
ad2a7909a1 AM3517: move AM3517 specific mux defines to generic header
AM3517 specific CONTROL_PADCONF_* defines moved from board-specific
files to <asm/arch-omap3/mux.h>

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2011-12-06 23:59:36 +01:00